DL12/13/14/18 Owner’s Manual BILLY GOAT DL TRUCK LOADER VACUUM Owner's Manual DL1201L, DL1301H, DL1401SE, DL1801V, DL1801VE Accessories INTAKE EXHAUST HOSE REPLACEMENT KIT *EXHAUST HOSE KIT HANGING EXTENSION KIT *EXHAUST EXTENSION KIT Standard on DL units. [8"(203mm) x 10' (3.0m)] [10”(254mm) X 10’(3.0m)] [7"(203mm) x 5' (1.5m)] flexible hose increases exhaust distance. Allows the Debris loader to hang from a vertical side panel.
DL12/13/14/18 Owner’s Manual CONTENTS SPECIFICATIONS AND SOUND/VIBRATION 3 INSTRUCTION LABELS 4 PACKING CHECKLIST ____________ 5 ASSEMBLY AND MOUNTING 6 OPERATION 7 MAINTENANCE________________________________ 8-9 TROUBLE SHOOTING__________________________________________________10 ILLUSTRATED PARTS & PART LISTS 11-13 Go to http://www.billygoat.com for French-Canadian translations of the product manuals. Visitez http://www.billygoat.
DL12/13/14/18 Owner’s Manual Specifications DL1201L Engine: HP DL1301H DL1401SE DL1801V DL1801VE 12 (8.95 kW) 13 (9.69 kW) 14 (9.69 kW) Engine: Model HK291150124P-BPQE2 GX390U1QA2 EX400DE5030 3564420186EI 3564470288B1 Engine: Type LCT OHV HONDA SUBARU BRIGGS AND STRATTON BRIGGS AND STRATTON 6 qt. (5.68 L) 6.9 qt. (6.5 L) 7.4 qt. (7.0 L) 9qt. (8.52 L) 9qt. (8.52 L) Engine: Fuel Capacity 18 (13.4 kW) 18 (13.4 kW) Engine: Oil Capacity 0.875 qt. (0.8 L) 1.16 qt. (1.1 L) 1.3 qt.
DL12/13/14/18 Owner’s Manual INSTRUCTION LABELS ® The labels shown below were installed on your BILLY GOAT DL Vacuum. If any labels are damaged or missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The correct position for each label may be determined by referring to the Figure and Item numbers shown.
DL12/13/14/18 Owner’s Manual PACKING CHECKLIST Your Billy Goat is shipped from the factory in one carton and is completely assembled except for the exhaust elbow, nozzle, handle loop for nozzle, hose booms, hose bands, hose coupler, hose clamps and related hardware. READ all safety instructions before assembling unit. TAKE CAUTION when removing the unit from the box.
DL12/13/14/18 Owner’s Manual ASSEMBLY 1. SECURELY ATTACH unit to the bed of a truck, trailer, or use the hanging brackets, so that the exhaust discharges into an enclosed container. NOTE: This unit must be securely mounted to the bed of a truck or to a trailer before operating. See page 14 for parts diagram to assemble 2. ATTACH hose to housing intake, using hose quick clamp (item 8) making sure to place the safety switch under the clamp (see interlock page 12.
DL12/13/14/18 Owner’s Manual VACUUMING OPERATION IMPORTANT: With the machine off and spark plug disconnected check the condition of the replaceable liner before every use and replace if necessary. EXHAUST DIRECTION & DISTANCE: Exhaust direction and distance are controlled by the rotation of the exhaust elbow. Typically debris is aimed to discharge to the rear of the container. The direction of discharge is adjusted by rotating the exhaust elbow on the housing and securing with the hardware provided.
DL12/13/14/18 Owner’s Manual MAINTENANCE PERIODIC MAINTENANCE Periodic maintenance should be performed at the following intervals: Maintenance Operation Every use Every 5 hours (daily) Every 10 Hours Every 25 Hours Inspect for loose, worn or damaged parts.
DL12/13/14/18 Owner’s Manual Battery Care (For Electric-Starting Models) Proper care can extend the life of a battery. Follow these recommendations to ensure your battery’s best performance and long life: • Do not allow the battery charge to get too low. If the machine is not used, charge the battery every 4 – 6 weeks. Operate the engine for at least 45 minutes to maintain proper battery charge. • Store an unused battery in a dry area that does not freeze. • Do not charge an already charged battery.
DL12/13/14/18 Owner’s Manual Troubleshooting Problem Abnormal vibration. Engine will not start. Possible Cause Loose or out of balance impeller or loose engine · Nozzle buried in debris. Clogged hose or exhaust. Excessive quantity of debris. · Throttle & / or stop switch in off position. Out of gasoline. Bad or old gasoline. Spark plug wire disconnected. Harness wire is bad or disconnected from interlock switch. Hose not installed, allowing interlock wire to ground. Dirty air cleaner.
DL12/13/14/18 Owner’s Manual PARTS DRAWING DL 56 79 53 57 60 43 40 63 80 75 72 46 73 27 9 10 59 14 65 36 DL18VE MODEL 47 12 11 48 53 1 71 46 31 52 18 77 69 43 30 26 6 54 13 68 42 67 70 17 20 21 7 19 8 76 63 21 23 44 27 55 DL18V MODEL 47 36 35 33 * TO ENGINE 66 34 88 43 22 46 16 48 1 39 71 46 69 29 68 31 77 41 24 40 45 67 70 50 51 35 ON 28 103 DL18V MODEL 43 30 26 5 64 49 3 61 28 40 41 25 41 38 46 4 47 2 32 15
DL12/13/14/18 Owner’s Manual PARTS LIST ITEM NO.
DL12/13/14/18 Owner’s Manual SCREWCAP 5/16-18 X 2" HCS ZP WASHER 1/4" ZP KEY 1/4 SQ X 2 3/4" KEY 1/4 SQ X 3 1/4 BOLT CARRIAGE 3/8 -16 X 1" ZP WASHER 3/8 FLAT CUT NUT LOCK 3/8-16 HEX ZP BOLT CARRIAGE 5/16" - 18 X 3 1/2" ZP NUT LOCK 5/16-18 HEX ZP NUT FLANGE 5/16-18 HEX ZP SCREWCAP 3/8-16 X 3" HCS ZP SCREWCAP 3/8-16 X 1 3/4" HCS ZP WASHER 5/16 FLAT ZP SCREWCAP 5/16-18 X 1 3/4" HCS ZP SCREW SM 1/4 X 3/4" TYPE AB HX WF HEX WASHER FACE BOLT 3/8-16 X 3/4 SCREWCAP 3/8-16 X 1" HCS ZP WASHER 3/8 SAE SCREWCAP 1/4"-2
