FORCE BLOWER PUSH Owner’s Manual Patent #6,253,416 and other patents pending F902S, F902H, F1302H, F1802V BILLY GOAT FORCE BLOWER Owner's Manual Accessories HOLD DOWN KIT To secure blower for transportation on trailer floors. P/N 440120 Part No 440313 SOLID FRONT TIRE Solid flat-free front tire. PARKING BRAKE Effective and Easy to use to prevent blower from rolling. CASTER KIT For greater maneuverability on hard surfaces.
FORCE BLOWER PUSH Owner’s Manual CONTENTS SPECIFICATIONS _______________________ 3 INSTRUCTION LABELS 4 PACKING CHECKLIST 5 ASSEMBLY 6 OPERATION MAINTENANCE AND TROUBLESHOOTING __ 7 ____ 8 ILLUSTRATED PARTS LIST 9 PARTS LIST 10-11 Go to http://www.billygoat.com for French-Canadian translations of the product manuals. Visitez http://www.billygoat.
FORCE BLOWER PUSH Owner’s Manual Specifications F902S Engine: HP F902H F1302H F1802V 9.0 HP (6.6kW) 9.0 HP (6.6kW) 13.0 HP (9.6kW) Engine: Model EX270D50021 GX270K1QA2 GX390K1QAA2 3564420224E9 Engine: Type SUBARU OHC HONDA OHV HONDA OHV B & S VANGUARD Engine: Fuel Capacity 6.4 qt. (6.1L) 6.3 qt. (6.0L) 6.5 qt. (6.1L) 9 qt. (8.52L) Engine: Oil Capacity 1.05 qt. (1.0L) 1.16 qt. (1.1L) 1.16 qt. (1.1L) 1.75 qt. (1.66L) Total Unit Weight: 138 # (62.6Kg) 143 # (64.8Kg) 160 # (72.
FORCE BLOWER PUSH Owner’s Manual INSTRUCTION LABELS The labels shown below were installed on your BILLY GOAT ® FORCE Blower. If any labels are damaged or missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The correct position for each label may be determined by referring to the Figure and Item numbers shown.
FORCE BLOWER PUSH Owner’s Manual PACKING CHECKLIST These items should be included in your carton. If any of these parts are missing, contact your dealer. Your BILLY GOAT ® FORCE Blower was shipped in one carton, completely assembled except for the Upper Handle Assembly and Front Diverter. Mounting hardware for the Upper Handle Assembly can be found in the parts bag. READ all safety instructions before assembling unit.
FORCE BLOWER PUSH Owner’s Manual ASSEMBLY 1.Follow the steps in figures A and B, then securely tighten all hardware shown. 2.Connect spark plug wire. Figure A Figure B The hardware for attaching the upper handle to the lower is in the parts bag. Install upper handle (item 30), to preassembled lower handle (item 28) by sliding the upper over and down the outside of the lower handle. Using bolt (items #36 and 71), washers (item #10) & lock nut (item #11) to install upper handle to lower handle.
FORCE BLOWER PUSH Owner’s Manual BLOWING OPERATION Your Billy Goat Force blower is equipped with an air director cone and the patented Aim-N-Shoot TM control lever to allow the operator to direct the air stream up or down as required to assist in moving debris. This feature is extremely useful when debris has piled up to the point that it cannot be blown any farther. The air stream can be directed upward to blow the top of the debris pile over and allow the operator to continue moving more debris farther.
FORCE BLOWER PUSH Owner’s Manual MAINTENANCE PERIODIC MAINTENANCE Periodic maintenance should be performed at the following intervals: Maintenance Operation Every Use Daily or Every 5 Hours Every 25 Hours Every 50 Hours Every 100-150 Hours z Inspect for worn or damaged parts. z Check for excessive vibration z Inspect Impeller for cracks or damage z Inspect for loose parts. IMPELLER REMOVAL 1. 2. 3. 4. 5. 6. Wait for engine to cool and disconnect spark plug.
FORCE BLOWER PUSH Owner’s Manual ILLUSTRATED PARTS LIST Part No 440313 9 Form No F060811D
FORCE BLOWER PUSH Owner’s Manual PARTS LIST F1302H F902H F902S F1802V ITEM NO. DESCRIPTION PART NUMBER QTY. PART NUMBER QTY. PART NUMBER QTY.
FORCE BLOWER PUSH Owner’s Manual ITEM NO. 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 125 DESCRIPTION SADDLE LOWER DIVERTER SCREW PLASTITE #10-14 X 1" PIN PIVOT DIVERTER CONTROL RING RETAINING 5/16 CABLE ASSY DIVERTER PIVOT ADAPTOR SPRING EXTENSION 0.468 X 5.25 BRACKET DIVERTER FORCE PIN CLEVIS 1/4 X 3/4 .051 X 3/4" HITCH PIN CLIP EYEBOLT PIGTAIL 5/16"-18 X 1 1/4" ADAPTOR MOUNT WA GRIP 1-1/4" ID x 9.5" LONG TY-WRAP WASHER .765 ID X 1.25 OD X 0.