BINAR PRODUCTION SYSTEMS Industrial IoT Gateway LP304 USER MANUAL
Industrial IoT Gateway LP304 User manual 2021-09-01 eng 1.00 Binar Solutions AB Box 2001 • SE-461 11 TROLLHÄTTAN • Sweden Tel +46 (0)520 47 32 00 e-mail info@binar.se • website www.binarsolutions.
Contents 1- System overview .............................................. 4 2-User interface ................................................... 5 2.1 The main menu ................................................ 5 2.2 System ............................................................. 5 2.3 Network ........................................................... 5 2.4 Local Settings ................................................... 5 3- Connectors ......................................................
1- System overview The LP304 is a powerful industrial IoT Gateway that enables master systems to control equipment on the production shop floor. Binar has a broad range of products that are used to build efficient support systems for Lean Manufacturing. The gateway acts as a bridge between a master system and the different hardware modules on the shop floor.
2- User interface 2.1 The main menu Press Home Return to Home page Status Show System status page Network Configure Network Settings Local settings Show Local Settings page 2.2 System Section I/O Shows the I/O signal status (In or/and Out) Active or Not Section CAN Shows status for the CAN bus (connectors X1 and X2) Section BWS Show if BWS (Binar wireless System) is active or Not and what devices are contacted throw it. 2.
3- Connectors 3.1- Connectors overview 1. I/O CONNECTOR: 4 IN, 2 OUT. M12, 8 poles 2. Ethernet: RJ45 3. CAN: 3A: IN or 24VDC max 4Amp, M12 5 pin male A code 3B: OUT, M12 5 pin female A code 4. USB: 6. 4A: USB 2.0 4B: USB 3.0 Power in: 24VDC, Max 4Amp. M12, 4 pin T code 8. Wireless Antenna: Binar Wireless System (BWS) antenna 8 Future Options HDMI: LP304P PROFINET: 5. 7.
3.2- Parts and accessories PART NO DESCRIPTION WHEN TO USE 51326 Power Supply LP-PW14 24VDC 4Amp To supply CAN bus single with power. 35423 Binar Wireless antenna When wireless connection to BWS (Binar Wireless System) is required. 50151 Binar Wireless Antenna incl Ext cord and bracket When LP304 needs better wireless signal. Binar Solutions AB Box 2001 • SE-461 11 TROLLHÄTTAN • Sweden Tel +46 (0)520 47 32 00 e-mail info@binar.se • website www.binarsolutions.
4- Mechanical dimensions and mounting LP304 comes with mounting brackets attached and mounting is done by means of four screws, size M5 to M6 (see dimensions below). Mounting is preferably done in line of sight of the connected tool, with the display at least at operator’s eye level, preferably a bit higher. DO NOT place LP304 in a metal enclosure as that would block the wireless communication. Binar Solutions AB Box 2001 • SE-461 11 TROLLHÄTTAN • Sweden Tel +46 (0)520 47 32 00 e-mail info@binar.
5- Technical Data TECHNICAL DATA DATA Power supply 20-30 VDC Data transfer CAN, 1 IN & 1 OUT Ethernet, 1 port Binar Wireless System Protocols device interface REST, MQTT CE RED & RoHS Temperature range 0 - 50 °C Humidity 0 - 95 % non-condensing Enclosure IP41 Mounting Mounted with screws Weight 650 g Dimensions w 150 x h 142 x d 55 mm BINAR WIRELSS SYSTEM Frequency 2.4 GHz Output +5 dBm Type IEEE 802.15.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
