TREND 3 EXECUTIVE Corded Telephone Unpacking your phone In • • • • the box you will find: Base Unit Handset Coiled Handset cord Telephone line cord for Base unit • User manual Keep the packing materials in a safe place in case you later need to transport the unit. Keep your sales (till) receipt, which is your guarantee. Important note---back up batteries The Trend 3 Executive requires 2 x 1.5V AAA size Alkaline batteries installed into the battery compartment before use.
1. Where to find it 12 1 4 3 6 11 2 MENU DEL BACK CHECK Tel No 8 9 13 5 new M1 7 10 3 Executive 1. LCD Screen 2. Scroll Up & Down buttons 14 3. Call Back button 4. Delete button 5. Check button 6. Store button 7. Secrecy button 8. One-Touch Memory button 9. Pause button 10.R(Recall) button 11.Battery Compartment 12.Telephone Line Socket 13.Ringer Volume Switch 14.LNR(Last Number Redial) button Binatone Help Line - 0845 345 9677 Calls are charged at Local Call rate.
2. Installation 1. Locating the Base unit The Base unit should be placed on a level surface, in a position where: the telephone line cable will reach your telephone line socket or extension socket. it is not close to a sink, bath or shower, or anywhere else where it might get wet. it is not close to other electrical equipment - fridges, washing machines, microwave ovens, TVs, fluorescent lights, etc. 2. Plug the coiled handset cord into the Handset.
3=L?Q >LCP?L NI IJ?H <;NN?LS >IIL 06x JF;N? 4?F?JBIH? HOG Installing (or Replacing) the Battery IMPORTANT - Before removing the battery compartment cover, always make sure the base unit is disconnected from the telephone line. M1 Use a screwdriver to remove the screw in the battery compartment cover on the top of the base unit. Install 2 pcs of Alkaline AAA batteries into the battery compartment and place back the cover before use.
3. Wall mount installation To place the Trend 3 Executive phone on a wall, mark two points on the wall that are 130 mm apart to lay the fixing centers as shown below. 130 mm Wall mount Slide-back in IMPORTANT Before you wall mount, please check that: you are not drilling into any hidden wiring the telephone line cord will reach the telephone socket Fix two screws at the marketed locations, leaving approximately 7mm between the wall and the screw head.
4. Setting up your phone Press the MENU button to enter the menu and then use UP or DOWN buttons to cycle through the following options: SET 1 DATE SET 2 LCD SET 3 FLASH Note: The system will time out if you leave more than 8 seconds between key presses. You will need to set the correct time and date so they can be displayed correctly on the display. Set Time/Date If you subscribe to a Caller Display service, the time and date will be set automatically on receipt of your first incoming call.
10 MENU Press UP or DOWN button to set the minute. 11 12 MENU DEL Set LCD Contrast 1 MENU MENU 4 5 MENU Set Flash Time MENU 4 Press MENU to confirm. Press MENU button to confirm the setting. Ö The display shows ' SET 2 LCD ' , you can continue with programming, or press DELETE button to return to standby mode. This telephone gives you the possibility to use the special services of your network provider.
5 MENU DEL Press MENU button to confirm the setting. Ö The display shows ' SET 1 DATE ' , you can continue with programming, or press DELETE button to return to standby mode. 5. Telephone Operations Making a call Receiving a call 1 Lift the Handset, listen for a dial tone. Ö The display shows ' 00-00 '. 2 Dial the telephone number you wish to call. Ö The display shows the number as you dial (maximum of 14 digits will be shown). 3 To end the call, return the Handset to the Base unit.
Mute Function 1 During a call press SECRECY button. Ö When the mouthpiece is muted, the person at the other end of the call cannot hear you but you can hear his side. 2 To get back to the call, release SECRECY button again. For some switchboard system, an access number must be dialed (usually an 8 or 9) to get another dial tone and an outside line. Inserting a Pause in the dialing sequence Pressing PAUSE button immediately after the access number, a pause of about 3.
Deleting an 1 outgoing call record 2 CHECK 3 DEL 4 DEL Storing a 1 Number in a One-Touch 2 memory Dial out Stored number CHECK In waiting mode, press CHECK button. Ö The most recent outgoing call number and duration will be displayed. Press CHECK repeatedly to find the record you wish to delete. Press DELETE button. Ö The display shows the next record. Press and hold DELETE button 3 seconds will delete all outgoing call records. Lift up Handset, press STORE button.
Condition of Incoming Caller Information It is a duplicate one It is a new one It has exceeded the range of the service It is a secret one It may not be nicety for the reason of outside There is a voice information in your mailbox (This function is available only when you have applied for this service from your telecommunication network) LCD Screen will display REP NEW UNAVAILABLE WITHHELD ERROR Caller Display list Trend 3 Executive dynamically stores up to 50 groups (8digits) incoming information.
7. Operational notes Electrical safety DON’T let the Base unit get wet. Electrical equipment can cause serious injury if used while you are wet or standing in water. If the Base unit ever falls into water, DON’T retrieve it until you have unplugged the power lead from the mains and the telephone line plug from the telephone socket; then pull it out by the unplugged cables.
8. Troubleshooting ! The Trend 3 Executive must be serviced by trained engineers. NEVER attempt any repairs or adjustments yourself - you could make the problem worse and invalidate the guarantee. ALWAYS check first that: you have followed the steps listed on Section 2 to install and set up your Trend 3 Executive. all connectors are firmly inserted in their sockets. the batteries are correctly and securely installed, and are not run down. Everyday use “I cannot make or answer calls.
PBX use “Last Number Redial and/or memory dialing don't work on a PBX” When you first make a call, try pressing the PAUSE button for s pause between the outside line access digit (e.g. 9) and the telephone number.You should later be able to redial the number. When storing numbers in memory, you can include the outside line access digit (e.g. 9) with each number.
9. Guarantee and service The Binatone Trend 3 Executive is guaranteed for 12 months from the date of purchase shown on your sales receipt. The Guarantee does not cover damage by misuse or negligence, or by excessive voltages - for example, faults on the telephone line, or lightning. This does not affect your statutory rights. Please keep your sales (till) receipt - this is your guarantee. You should also keep the original packaging material.
10. Technical details Standard Trend 3 Executive Telephone Temperature range Operating 0 ºC to 40 ºC Storage -20 ºC to 60 ºC PBX compatibility Timed break recall: 98 ms. Pause length: 3.6 seconds. Signalling type: DTMF (dual-tone multifrequency) also called tone dialing. Network connection This equipment is intended to be used in the UK only. Operation on other countries’ PSTN termination points cannot be guaranteed.
Connection and conditions for use You can connect your Trend 3 Executive phone to a direct exchange line (DEL) - a line connected to a local exchange, with its own phone number; to an extension socket connected to a DEL; or to an extension on an approved compatible PBX. Do not connect the Trend 3 Executive phone as an extension to a pay phone. The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.