A7 OWNER’S MANUAL
TABLE OF CONTENTS PRODUCT INFORMATION Important Safeguards.............................................4 Cautions Before Installation.................................6 Safety Information....................................................9 Main Unit & Parts......................................................12 PRODUCT INSTALLATION Installation....................................................................14 Operation......................................................................
IMPORTANT SAFEGUARDS READ ALL OPERATING INSTRUCTIONS BEFORE INSTALLATION NOTES 1. This product should be installed according to this manual. 2. Read this manual carefully and install properly. 3. Keep this instruction manual in an easily accessible place. 4. Do not attempt to service this appliance yourself. Doing so will void the warranty. DANGER - To reduce the risk of electric shock: 1. Do not place or store this appliance in a location where it can fall or be pulled into a tub or sink.
CAUTIONS BEFORE INSTALLATION NOTE THE FOLLOWING IMPORTANT POINTS 1. Do not install in a location where water might be splashed on this appliance or in a location exposed to excessive moisture where condensation might form on the product’s surface. 2. To avoid damage to electronic components due to high levels of humidity, provide adequate ventilation by opening a window and/or door when bathing. 3. Water supply should have a water pressure of 0.07 MPa to 0.74 MPa. 4.
CAUTIONS BEFORE INSTALLATION (CONT.) 3. This product is for use on a nominal 120V circuit. It has a grounding plug that is similar to the plug illustrated in sketch A. A temporary adapter, which looks like the adapter illustrated in sketches B and C may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until the properly grounded outlet (sketch A) can be installed by a qualified electrician.
SAFETY INFORMATION (WARNING) WARNING - MIGHT CAUSE SLIGHT INJURY OR DAMAGE. BE AWARE. 10 • Be aware of low-grade burn. It may result in a low-grade burn if sitting on the heated sat for a long time. Be aware if being used for the following: children, senior citizens, patients, people who cannot control the temperature, people who are not sober, or people who are tired. If injured in a low-grade burn, see a doctor immediately. • Do not step on or place heavy objects on this appliance.
MAIN UNIT & PARTS 15mm 8mm (7/8” to 3/8” and 1/2” to 1/2”) 12 13
INSTALLATION If electric work is needed, please contact a qualified electrician or service man only. Remove the existing toilet lid and seat 1. Remove the nuts, washers, and cone packings from the toilet seat and mounting bolts in the back of the toilet. 2. Remove the toilet seat, lid, and mounting bolts. Mounting the Plate Place the mounting plate over each mounting hole. Insert the mounting bolts through the plate and mounting holes.
INSTALLATION (CONT.) How To Attach the Unit 1. Trial Operation Use the tab on the mounting plate and align it with the track on the seat, for proper fit. 1. Preparation Plug the power cord into the outlet, and then the water tank will be filled in 2 minutes. 2. Checking All Functions Cover the toilet bowl using the sheet of plastic wrap on the unit to prevent the washing water from being sprayed out of the toilet. Then check for all function described in this manual. 2.
OPERATION CAUTION 1. All Functions will be operational when the seat is occupied except Nozzle Cleaning. AUTO • Press “Auto: during the operation of “Cleansing” or “Bidet” • Cleansing wash, oscillating wash and oscillating with massage will operate for each 20 seconds consecutively. • If the bidet Auto wanted, press “Bidet” and “Auto” consecutively. 2. Before operating, ensure that water tank is filled up completely. STOP • Press “Stop” to stop current operation.
OPERATION (CONT.) LED BAR • All functions will show tis duration or setting on the LED bar. SOUND • Press “Sound” to enable the beeping sound. • To Disable, press the button again. LED • Press the button to activate LED Light. • Delicate light will help user to use toilet without turning the light on during night time. TEMPERATURE ADJUSTMENT (seat & water) • Temperature of seat and water can be adjusted.
CLEANING CAUTION: Do not forcefully push, pull, or bend the nozzles. It may result in failure. Make sure to use the “Stop” button on the side control panel. Strainer Maintenance • This appliance will not operate properly if the strainer is clogged. Be sure to clean the strainer regularly. NOZZLE CLEANING Manual Cleaning 1. Make sure the occupied sensor is not activated. (Do not sit on the seat or place hands on the seat sensor) 2. Press “Front” button for 3 seconds to extract the nozzle. 3.
MAINTENANCE Draining Water - while not using over extended period of time. 1. Unplug the Power Supply Cord. • 5. Screw the Drain Bolt and Install the Appliance • Refer to the trial operation method in order to use this appliance again. Not doing so may cause fire. Preventing Freezing 2. Close the Shutoff valve. 1. Make sure the power cord is plugged properly. 2. Set the temperature of water to low or middle. (Freezing can be prevented by thermal efficiency of water tank.
BEFORE CALLING FOR SERVICE PROBLEM Completely fails to work POSSIBLE CAUSE • • • Water does not spray • • • • Water is leaking or dripping Seat or water is not warm enough 26 • • • Is there a power cord outage? Is the power cord unplugged? Are you sitting on the seat correctly? SPECIFICATIONS SOLUTION • • • Is the water shutoff valve closed? Is the strainer clogged? Are the nozzles clogged? Is the water purifying filter clogged? • Are all the hoses tightened up properly? • Is the temperatur
WARRANTY USPA Personal Hygiene Appliance Limited Warranty We warrant our products to be free from manufacturing defects under normal use and service for a period of one (1) year from the date of purchase. 100% Coverage of all parts and labor for the entire product for the first year from original date of purchase. This warranty is only valid within the United States and Canada.
Thank You Technical Support/Customer Service 7900 S Route 31 Crystal Lake, IL 60014 T: 847.458.2334 U.S. TOLL FREE: 877.339.5214 support@biobidet.com www.biobidet.
