Operating Instruction Manual A8 Thank you for purchasing this USPA bidet seat. You are kindly requested to carefully read this operation. manual for proper use of this appliance. Please save this manual and place it in an easily accessible location. Please register warranty for proper service.
After installation all other servicing should be performed by authorized service representatives. This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire and grounding plug. They must be plugged into an outlet that is properly installed and grounded.
Lid (seat cover) Caution label Deodorizer Power plug Nozzle Side control buttons Heated seat Occupied sensor Accessories Remote Control Mounting bolt (2pcs) Cone packing (2pcs) 1 2 (15mm) (8mm) Water supply hose (2pcs) Remote control Remote control Bracket Screw (2pcs) Plastic anchor (2pcs) Washer (2pcs) T-valve Nut (2pcs) 3/8” Spare nut package ※ Hose clip (5pcs) s Mounting Plate AAA Battery (3ea)
Place the mounting plate over each mounting hole. Insert the mounting bolts through the plate and mounting holes. Slide cone packings and washers onto the bolts and fasten tightly with nuts. Slide the unit until it clicks into the plate. While pressing the detach button, pull the unit forward and separate it from the toilet bowl. The toilet dimensions must be within those shown below. Do not install this appliance on a toilet that does not meet these dimensional requirements.
If a filter is used, it must be replaced every 3 months. This product is designed and intended for use exclusively with BioBidet USPA water filters. The purchase or use of any other water filter is not the responsibility of BBC Innovation. As such, any use of non USPA water filters is prohibited and will void the warranty for those BioBidet products. BioBidet will not be responsible for any resulting damages or claims related to the misuse or distribution of non BioBidet USPA filters.
Dry - Press "Dry" Warm air will come out for 3 minutes. - To alter the strength of drying, press the button again. - Dry temperature can be adjusted by pressing LOW or HIGH button to 5 levels. Cleansing - Press "Cleansing" to clean your posterior. The function will stop in 2 minutes automatically. - Press this button again to activate oscillation. The nozzle moves back and forth automatically to widen cleansing area. - Oscillation wash stops if this button is pressed again.
Massage - Press "massage" to activate rhythmical wash for massage effect when you are using "cleansing" or "bidet". - Press the button again to release this function. Kids - Press "Kids" to change all functions to be suitable for children. It will automatically operate from cleansing(2 min) to dry(3 min) with adequate water pressure and nozzle position. - This unit should be used under the supervision of an adult. Auto - Press "Auto" during the operation of "Cleansing", Cleansing wash (20 sec.
- This function is useful for public toilets when more than one unit of this product is installed. - To prevent interference among units, main unit and remote control should be set with the same ID. - If there is only one unit in the bathroom, you do not need to set ID. - Initial ID of remote control and main unit are "0". There are 16 choices in ID(00~15). HOW TO SET ID [REMOTE CONTROL] - Press "High"( ) button for 3 seconds and ID shows up in display.
- Use side control buttons on unit when remote control is broken or its batteries are dead. - Press “Cleansing” or “Bidet” to start. - Press again to stop. Do not use sharp items to press buttons. CLE ANS ING /STO P B IDET /PO WER CLEANSING / STOP BIDET / POWER USER SETTING -Each button can save 2 setting.(Cleansing, Bidet) -Press User 1 button and Cleansing or Bidet consecutively. Then Choose nozzle positon by pressing FRONT / REAR button and water pressure level by pressing LOW / HIGH button.
Do not forcefully push or pull the nozzles, or bend them. It may result in failure. Make sure to use“Stop”button on the remote control. Make sure the occupied sensor is not activated. (Do not sit on the seat or place hands on the seat sensor) Press Front( ) button for 2 seconds to extract the nozzle. Use a tooth brush or soft cloth to clean the nozzle. Press Stop button to retract the nozzle. Press Rear( ) button for 2 seconds to start auto cleaning.
Unplug the power supply cord. - Not doing so may cause fire. While pressing the detach button, pull the unit forward and separate it from the toilet bowl. Close the shutoff valve. Uphold the appliance and thoroughly drain the water by unscrewing the drain bolt. (Beware of losing the drain bolt) Screw the drain bolt and install the appliance. - Refer to the trial operation method in order to use this appliance again.
- Press "eco" again to release the function AC 120V 60Hz 1248W Direct connection to tap water 0.07MPa ~ 0.74MPa Air temperature Dry 700 (±150)㎖/min 700 (±150)㎖/min 740㎖ Room temp ~ 39℃(102℉) 1200W Thermal switch, Temperature fuse, Floating switch Room temp ~ 60℃(140℉) 250W Temperature fuse, Bimetal Room temp ~ 39℃ (102℉) 48W Temperature fuse Catalystic filter Within 15mA 0.03 second 1.2m (W)410 mm(16.14 inches) X (L)528 mm(20.79 inches) X (H)160 mm(6.30 inches) 4.0Kg(8.
