Instruction manual
• When not in use, store the electrode gel pads on the
plastic pad protectors provided at room temperature.
• Keep the electrode gel pads clean and dust free in a
dry location, keep away from oily or sticky objects. The
life of the electrodes varies depending on skin
conditions, storage, amount of use, type of
stimulation, and stimulation site. Usage may be
extended by carefully cleaning the gel surface with a
soft damp cloth. Do not get the cables wet when
clea
ning.
• F
or hygiene purposes this is a single patient use
only device.
• The adhesive will become less effective if the gel pad
is contaminated. Wash the pads under slow running
water for about 2 - 3 seconds. Caution! Do not use
hot water. Do not wipe the adhesive surface. Let the
adhesive surfaces of pads air-dry. Adhesive surface
sides up during drying.
• To sterilize the foot plate use a mild antiseptic
solution.
• Do not use tissue, cloth etc. to scratch the
electrode surface.
• D
o n
ot use anything abrasive to clean the electrode
pads this will damage the pad surface.
• Do not frequently clean the pads, and do not use
detergent or hot water to clean the electrode gel pads.
• Turn off the power, remove the adaptor and the
electrode gel pad from the unit for storage in
correct way.
• Always keep the main device clean, by using a soft
cloth to clean the surface of the unit.
• To clean the foot plates use a soft, damp cloth, dry
thoroughly after cleaning.
•
To c
lean the main unit use a soft, damp cloth, dry
thoroughly after cleaning.
• Do not spill liquid on the device.
• Do not immerse the device in water.
• Do not clean with chemicals.
• Store in a dry, dust free location in a temperature
between 10˚C to 40˚C and 30% to 90% relative
humidity.
• Do not open the device or repair it yourself. This will
invalidate your warranty and may cause serious harm.
• If the device malfunctions, disconnect it from the
power source and contact your selling agent as soon
as possible.
• Use only the accessories supplied by the
manufacturer.
• Use the device only for its intende
d p
urpose.
• Do not expose the device to extreme heat.
• Do not overload the electrical outlet.
• Do not stand on the machine. Use it when sat
down only.
• Do not spill liquid on the device or its accessories
The warranty is void if the product has been altered,
misused or abused. We will not take any responsibility.
Regulatory Certification
UK/Europe Class IIa medical device
This symbol indicates that the unit meets the
basic requirements set by the CE Directive
93/42/EEC concerning medical devices.
ElectroFlex complies with the WEEE Directive.
Disposal of the device in accordance with
EU regulations applicable at the place of
operation. Dispose of at public collection
points in EU countries.
ISO 13485 – Manufactured under the international
quality management standard for medical devices.
Device will Batteries inserted in wrong direction Insert batteries in correct direction or check the
not turn on battery is not discharged
The adaptor is not connected to the Check the connection of the adaptor jack is properly
device correctly connected to the device and in the wall socket
Power turns off Gel pads not attached Attach Gel pads correctly to the skin
too soon correctly to the skin
Power turns off If you are using the batteries operation, Fit three new 1.5V alkaline batteries type C
while using then the batteries are weak/exhausted
massager Treatment period of 25 minutes is over Restart treatment or turn off the massager
and power turns off automatically
If you are using the body massager, Replace electrode cord
the cable may be damaged
It is difficult to Transparent film not peeled off Peel off film on the adhesive surface of gel pad
attach gel pad Gel pad applied immediately Allow gel pad to dry
to the skin after washing
Adhesive surface of gel pad damaged Replace gel pad
The gel pads get dirty and lose their Replace gel pad or clean the gel pad with a small drop
adhesive/stickiness of water rubbed onto the sticky side of the electrode pad
Adhesive surface Use of gel pad during perspiring Chill the gel pad in a domestic fridge for 3-4 hours
of gel pad is sticky Gel pad washed too long and/or
too frequently
Gel pads stored under high temperature,
high humidity or direct sunshine
It is difficult to The soles of your feet are too dry Dampen the sole of your feet this will
feel stimulation increase conductivity
Your soles are not placed on the foot Ensure both of your soles are aligned on each foot
plates correctly plate correctly
Gel pads not attached correctly to Attach gel pad firmly to the skin
the skin
Gel pads overlap each other Reattach Long Life pads with no overlap
Electrode cord not connected correctly Connect electro
de c
ord correctly
Applied intensity too weak Increase the intensity by pressing the intensity button
The skin turns Adhesive surface of Gel pads is Wash adhesive surface of gel pads carefully whilst
red or the skin dirty or dry unplugged from machine and leave to dry thoroughly
feels irritated Adhesive surface of Gel pads damaged Replace gel pads
Hygiene
After using the product
• Clean the foot plate area with a soft, damp cloth and
a mild antiseptic solution.
• Store the electrode gel pads on the protectors
provided.
Storage
Keep the product clean and dust free store within the
following condition.
Storage temperature and humidity
-10˚C to 60˚C, 10% to 95% RH
Operating temperature and humidity
10˚C to 40˚C, 30% to 90% RH