Blood Pressure Monitor Model: 2006-2B Bioland Technology LTD. No. A6B7 (Block G) ShangRong Industrial Zone No. 5 Baolong Road, Baolong Community Longgang District 518116, Shenzhen, Guangdong PEOPLE’S REPUBLIC OF CHINA Toll-free service line: 800-218-2838 Mon-Fri 9AM-5PM EST Date of issue: 2019.04.
Table of Content Table of Content.............................................................................................................2 Introduction....................................................................................................................2 Precaution before use.....................................................................................................3 Few words about blood pressure...................................................................................
11. Any reading may be affected by the measuring position, the patient's position, Precaution before use 1. Do not confuse self-monitoring with self-diagnoses. movement, or the patient's physical condition Blood pressure 12. Failure to use the cuff specified by use manual, or modified instrument may result in incorrect measurements. measurements should only be interpreted by a health professional who is 13.
24. There is no allergic reaction to the accessible material on the device; 25. Children are not allowed to operate the device and should not eat any falling parts; 26. Stop measurement immediately and cut off the power supply when the hose in the sleeve belt causes neck strangulation, so as to avoid damage to human body Few words about blood pressure Please consult your physician to determine if your blood pressure accurately reflects your actual blood pressure Your blood pressure changes constantly.
* Talking * Taking a bath * Drinking alcohol * Smoking, etc. Note: One or two readings will not provide a true indication of your normal blood pressure. It is very important to take regular, daily measurements and to keep accurate records. In partnership with your doctor, an accurate record of your blood pressure over a period of time can be a valuable aid in diagnosing and preventing potential health problems.
Environment Protection – Waste electrical products should not disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice. Install or replace batteries When the battery symbol appears on the display or nothing is display while inflation How to use the upper arm cuff during measurement, you should replace with new batteries. 1. Press the snap hook on the battery cover to open it. 1.
better cross reference; Important! The mark (about 2 cm long bar) must lie exactly over the artery which 2. When measuring, the legs should not be crossed, feet flat on the ground, arms runs down the inner side of the arm. and back vertical. 3. When measuring, do not squeeze the hose of cuff, as this may cause injury or incorrect measurements. 4. Tighten the free end of the cuff and close the cuff with the closer. A few suggestion before measurement 5.
How to measure blood pressure arm cuff". Remain still and do not talk during the measurement. Position your arm higher than the heart will get lower measure result, contrarily the measure result will get higher. This unit can intelligently adjust the cuff pressure and inflate to a higher pressure level when needed, so its normal when the unit re-inflate during one measurement. 2. Press the power button, The LCD display and the voice guiding the correct Note: 1.
Recalling memory 1. Maintenance and repair Press “M” button to turn on the device, then press “M” button until enter 1. Do not wash or immerse the unit in water, use a soft and memory state like right figure. dry cloth to clean it. 2. Do not use the volatile liquids to clean the main unit or cuff. 3. Do not moisten the cuff, wash hands before measurement. 2. Press “M” or “S” button to check the next measurement data. 3. If there is no memory, it will display “—” and then turn off in one second. 4.
Specifications Symbols information Type BF applied part Indication Digital LCD display Pressure display Range: Pressure: 0-300 mmHg, Pulse rate: 40~195 Beat/min Pressure display Accuracy: Pressure: ±3mmHg; Pulse rate: ±5% Attention and read before use SYS 60 to 260 mmHg NIBP measurement range Indicates the medical device manufacturer Pulse rate 40 to 195 /min Indicates the authorized representative in the European community IP20 DIA 30 to 195 mmHg NIBP accuracy Maximum mean error within ±5mm
Troubleshooting EMC statement If you have trouble while using the unit, please check the following points first. This device has been tested and homologated in accordance with EN 60601-1-2 for POSSIBLE CAUSE EMC.
manufacturer. NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. Guidance and manufacturer’s declaration – electromagnetic emission The 2006-2B Blood Pressure Monitor is intended for use in the electromagnetic environment specified below.
Power frequency (50Hz/60Hz) magnetic field IEC61000-4-8 30 A/m 30 A/m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment. 80 MHz ~ 2.7 GHz Guidance and manufacture’s declaration – electromagnetic immunity The 2006-2B Blood Pressure Monitor is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.
electromagnetic site survey should be considered. If the measured field strength in the location in which the 2006-2B Blood Pressure Monitor is used exceeds the applicable RF compliance level above, the SD1Ultrasonic Doppler should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the 2006-2B Blood Pressure Monitor. b. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m. c.
