Owner's Manual

ManualsBrandsBionaire ManualsAir ConditionersBionaire BDQ25-UC

Read instructions before operating.

Retain for future reference.

Instruction Leaflet

INFO-LINE

If after having read this leaflet, you have any

questions or comments on your dehumidifier,

all 1-800-253-2764 in North America.

☎

uieTech

™

Dehumidifier

ODEL

BDQ25

DEHUMIDIFIER SAFETY

PLEASE READ AND SAVE

THESE IMPORTANT

SAFEGUARDS

When using electrical appliances, basic safety precautions

should always be followed to reduce the risk of fire, electric

hock, and injury to persons, including the following:

1. Read all instructions before using the appliance.

2. To avoid fire or shock hazard, plug the appliance

directly into a 120V AC electrical outlet.

3. Keep the cord out of heavy traffic areas. To avoid fire hazard,

NEVER put the cord under rugs or near heat registers.

. DO NOT place dehumidifier near heat sources such as

toves, radiators, and heaters. Locate your dehumidifier

n an inside wall near an electrical outlet. The

ehumidifier should be at least 4” away from the wall

or best results.

5. NEVER place dehumidifier in an area where it is

accessible to children.

6. Never place anything over the grill when the

unit is running.

7. NEVER drop or insert any object into any openings.

. DO NOT operate any appliance with a damaged cord

r plug, after the appliance malfunctions, or if it has

een dropped or damaged in any manner. Return

ppliance to manufacturer for examination, electrical or

echanical adjustment, or repair.

9. Use appliance only for intended household use as

described in this manual. Any other use not

recommended by the manufacturer may cause fire,

electric shock, or injury to persons. The use of

attachments not recommended or sold by the

manufacturer may cause hazards.

0.DO NOT use outdoors.

11.Always place dehumidifier on a firm, flat, level surface.

2.Dehumidifier should be unplugged when not in use.

13.NEVER tilt, move, or attempt to empty unit while it is

operating. Shut off and unplug before cleaning or

moving the dehumidifier. Be sure to unplug the

appliance by pulling on the plug and not the cord.

14.NEVER use detergents, gasoline, glass cleaner,

furniture polish, paint thinner, or other household

solvents to clean any part of the dehumidifier.

15.DO NOT attempt to repair or adjust any electrical or

mechanical functions on this unit. Doing so will void

your warranty. The inside of this dehumidifier contains

no user serviceable parts. All servicing should be

performed by qualified personnel only.

16. Never place housing under water flow or immerse in liquids.

17.Do not plug in the cord with wet hands: electric shock

could result.

18.NEVER operate the dehumidifier without the water

reservoir in place.

19.Use both hands when carrying the water reservoir.

RADIO FREQUENCY COMPLIANCE INFORMATION

his device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(

1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operation.

Modifications not authorized by the manufacturer may

void user’s authority to operate this device.

PLEASE SAVE THESE

INSTRUCTIONS

HOW YOUR DEHUMIDIFIER WORKS

our Bionaire

uieTech

™

ehumidifier draws moisture laden air

through the intake grills on the appliance. Humid air passes

through refrigerated coils where the moisture is removed and

collected in the water reservoir. This model is specially designed

to be ultra quiet and can be used in any room in the house.

NOTE: When the dehumidifier is plugged in the display will

ead the current room humidity level. The unit will remain in

standby mode until an operating mode is selected.

PRE-OPERATING INSTRUCTIONS

1. Select a location for your dehumidifier, on a flat/level

surface, about 4” away from the wall.

. If you choose to use an active carbon odor filter, pull

out the filter tray from the back of the dehumidifier.

Unpack the carbon odor filter, fit it into the frame and

replace the tray into the appliance.

. Plug the power cord into a 120V AC electrical outlet.

NOTE: The display will indicate the current room

humidity level when plugged in.

OPERATING INSTRUCTIONS

Your QuieTech

™

dehumidifier is equipped with SmartTouch

electronic humidity sensor which allows you to set and

maintain your desired humidity level by pressing one button.

Scroll through the presets of the electronic humidistat until

ou reach your desired comfort or power setting. The ideal

humidity for a comfortable room is between 40% and

60%. The dehumidifier will beep when scrolling through or

changing modes. This is normal.

1. Push the Mode button (mode / ) once to operate the

dehumidifier on the economy setting. This is the lowest

energy-use setting on the dehumidifier. The appliance

will turn on automatically when the humidity level is

above 65% and run until the humidity is reduced to

64%. NOTE: The dehumidifier uses electronic circuitry

designed to protect the compressor from damage

during start-up. This delays the start of the compressor

until the appliance has been running several minutes.

This delayed start is normal.

2. Push the button again to operate the dehumidifier on

the continuous mode. In this setting the appliance will

not turn off until the water reservoir needs to be

emptied or until the appliance is turned off.

. Push the button once more for a preset humidity

etting of 45% - 55%. The appliance will monitor the

oom humidity and automatically turn on and off to

chieve and maintain this desired setting.

4. Push the button again for a preset humidity setting of

55% - 65%. Again, the dehumidifier will automatically

sense the humidity and turn on and off to maintain your

desired comfort level.

5. The final push of the Mode button (mode / ) will turn

the compressor and fan off. The display and the back-

light will remain illuminated to show current room

humidity level. The compressor will turn off but the

dehumidifier fan will continue to run for a few seconds

to cool the unit down prior to turning off.

USING THE PORTABLE STATUS INDICATOR

Your Dehumidifier is equipped with a Portable Status

Indicator. This will allow you to place the indicator at a

convenient location within the home, up to 30 feet from the

ehumidifier, to determine the operating status of the

Dehumidifier as well as whether or not the Reservoir tank is

full and needs to be emptied. Your Portable Status

Indicator requires 4 "AAA" batteries (included).

Your dehumidifier also comes with a LED display panel.

This panel will assist you during operation with LED

indicators that illuminate to indicate the mode that the unit

as been set to.

Initializing the Portable Status Indicator

To set up your Portable Status Indicator prior to initial use,

please follow these instructions. Refer to Figure 2 for details.

1. Be sure the 4 “AAA” batteries are properly installed

2. Hold the “Mode” button on the Dehumidifier control

panel and the Backlight button (A) of the portable unit

at the same time for 3 seconds. Doing so will

synchronize the unit.

3. Release both buttons after 3 seconds.

Your Portable Status Indicator is now functional.

The Portable Status Indicator will display the humidity of

the room where the Dehumidifier is located. (Refer to letter

C in Figure 2)

It will also display the desired room humidity setting that

you initially programmed for the Dehumidifier.

An audible alarm will sound for a few seconds when the

Reservoir Tank is full and needs to be emptied. The “Tank

Full” icon ( ) on the Portable Status Indicator will flash

at this time until the reservoir is emptied. (Refer to letter E

n Figure 2)

The “Low Battery” icon ( ) on the Portable Status Icon

ill flash when the batteries need to be replaced. (Refer to

letter F in Figure 2)

Using the Backlight Button ( )

Your Portable Status Indicator is equipped with a Backlight

to aid in viewing the status of the Dehumidifier. To activate

the backlight, press the Backlight button ( ) (A) once.

The backlight will automatically turn off after 5 seconds.

Replacing The Batteries

our Remote Status Indicator is equipped with a Low Battery

signal. (Refer to letter F in Figure 2) When this is flashing

you must replace the batteries. To replace the batteries,

follow these simple instructions.

1. Remove the battery cover located on the back of the

Portable Status Indicator.

2. Remove the batteries. Discard of these batteries properly.

3. Insert 4 new “AAA” batteries in the orientation listed on

the Remote Status Indicator. Be sure to use new

batteries. Do not mix old and new batteries. Do

not mix alkaline, standard (Carbon-Zinc), or

rechargeable (Nickel-Cadmium) batteries.

4. Replace the battery compartment door.

EMPTYING THE WATER RESERVOIR

When the dehumidifier water reservoir is full the full light will

illuminate and there will be 5 beeps. Though the

dehumidifier is not collecting any more water the fan

will continue to operate even though the compressor

s turned off to cool the unit before

it shuts off.

1. Grip the reservoir drawer on the

front and pull out from the

Dehumidifier as shown in Figure 3.

Use your other hand to support the

reservoir once you've pulled it out.

2. Carefully carry the reservoir to a

nearby sink or tub and dispose of

the water.

3. Replace the empty reservoir.

Be sure the float mechanism is

positioned properly. See Figure 3.

4. The dehumidifier will automatically

resume operating at the previously

selected mode.

CONTINUOUS DRAINAGE/HOSE

ATTACHMENT

Your dehumidifier is equipped with a

reservoir bypass, which is located on

the back of the unit. A standard hose

of 1/2” (12.5mm) Internal Diameter

an be hooked up to the bypass port

to direct water outside or to a sump

pump. (Hose not included)

Step 1:Remove plug located on the back of the unit.

(See Figure 4)

his product is for use on 120 volts. The cord has a plug

(A) as shown. An adapter (C) is available for connecting

three-blade grounding-type plugs to two-slot recepta-

cles (B). The green grounding plug extending from the

adapter must be connected to a permanent ground such

as a properly grounded outlet box. The adapter should

not be used if a three-slot grounded receptacle is avail-

ble.

economy

ontinuous

5-55%

56-65%

full

mode /

Figure 1

A. Mode Button

B. LED Display

C. Full Indicato

D. Dehumidifier

Setting Display

Figure 3

Trouble Shooting

Trouble

• Display is not illuminated.

• Full light illuminated.

• Appliance cycles on/off.

• Appliance runs

continuously.

• E1 Code on Display.

• E2 Code on Display.

• Warm air coming from

outlet grill.

• Reserve tank leaks

robable Cause

☛ Unit not plugged in.

☛ Power failure.

☛

Reservoir is full

☛

Float mechanism is stuck.

☛

Tank is not fitting into

appliance.

☛

This is normal operation

when using the preset for

Economy or indicated

umidity settings. The

humidistat within the

appliance adjusts to

aintain your desired

comfort level. To run

continuously, select the

ontinuous mode (see

operating instructions).

☛ Room humidity is very

high.

☛ Dehumidifier is set to

continuous setting.

☛ Room temperature is not

within operating range

(below 40 degrees [4 °C]

or above 100 degrees F

[38 °C]).

☛ Room humidity is not

within operating range

(below 10% or above

98%)

☛ Heat exchange while the

compressor is on.

☛ Tank float -is not safely in

place

olution

✔ Plug unit in.

✔ Check circuit breaker or

outlet.

✔

Follow emptying

instruction in this manual.

✔

Remove reservoir and

adjust float, making sure

that it can move freely.

✔

Make sure tank is seated

in the appliance correctly.

✔ The dehumidifier will run

until humidity level is

reduced and reaches

your desired setting.

✔ Select one of the other

settings on the dehumid-

ifier (see operating

instructions).

✔ Wait until room tempera-

ture is within safe operat-

ing temperature.

✔ Relocate your dehumidi-

fier to another room and

operate normally.

✔ If below 10% you do not

need to run your dehu-

midifier at this time. If

above 98%, select to run

continuously.

✔ Relocate your dehumidi-

fier to another room and

operate normally.

✔ This is normal operation.

✔ Make sure the inside pin

on the tank float is

snapped fully into the

notch on the tank.

2 YEAR WARRANTY

Sunbeam Products, Inc. doing business as Jarden Consumer

Solutions or if in Canada, Sunbeam Corporation (Canada) Limited

doing business as Jarden Consumer Solutions (collectively “JCS”)

warrants that for a period of two years from the date of purchase,

this product will be free from defects in material and workmanship.

JCS, at its option, will repair or replace this product or any compo-

nent of the product found to be defective during the warranty period.

Replacement will be made with a new or remanufactured product or

component. If the product is no longer available, replacement may

be made with a similar product of equal or greater value. This is your

exclusive warranty. DO NOT attempt to repair or adjust any electrical or

mechanical functions on this product. Doing so will void this warranty.

This warranty is valid for the original retail purchaser from the date of

initial retail purchase and is not transferable. Keep the original sales

receipt. Proof of purchase is required to obtain warranty performance.

JCS dealers, service centers, or retail stores selling JCS products do

not have the right to alter, modify or any way change the terms and

conditions of this warranty.

This warranty does not cover normal wear of parts or damage

resulting from any of the following: negligent use or misuse of the

product, use on improper voltage or current, use contrary to the

operating instructions, disassembly, repair or alteration by anyone

other than JCS or an authorized JCS service center. Further, the

warranty does not cover: Acts of God, such as fire, flood,

hurricanes and tornadoes.

What are the limits on JCS’s Liability?

JCS shall not be liable for any incidental or consequential damages

caused by the breach of any express, implied or statutory warranty

or condition.

Except to the extent prohibited by applicable law, any implied

warranty or condition of merchantability or fitness for a particular

purpose is limited in duration to the duration of the above warranty.

JCS disclaims all other warranties, conditions or representations,

express, implied, statutory or otherwise.

JCS shall not be liable for any damages of any kind resulting from

the purchase, use or misuse of, or inability to use the product

including incidental, special, consequential or similar damages or loss

of profits, or for any breach of contract, fundamental or otherwise, or

for any claim brought against purchaser by any other party.

Some provinces, states or jurisdictions do not allow the exclusion or

limitation of incidental or consequential damages or limitations on

how long an implied warranty lasts, so the above limitations or

exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have

other rights that vary from province to province, state to state or

jurisdiction to jurisdiction.

Step 2: Cut the hose to expose a

bare piece of rubber with no

faucet connector attached.

Step 3: Insert the hose around the

bypass port located within this

open area. Be sure the hose is

completely inserted around this

bypass port by inserting it as far as

it can be attached. (See Figure 5)

Step 4: Direct the opposite end of the hose to a sump

pump or outside of your home far enough away from the

foundation to ensure proper drainage. The unit will now

direct water from the bypass port, rather than into the

water reservoir. (See Figure 5)

NOTE: The drain hose must be below the drain plug

in order for the unit to drain properly.

NOTE: To help prevent leakage, you should use a

marker to denote the location where the hose

meets the housing on the rear of the unit.

Periodically check to make sure this indicator has

not moved away from the housing to ensure that

your hose will not leak. Leakage inside the unit will fall

into the water reservoir. If this happens you can empty

the water reservoir by following the instructions above in

the “Emptying the Water Reservoir” section.

CLEANING THE NYLON FILTER

1. Turn the dehumidifier to standby mode ( ) and

disconnect it from the electrical outlet.

2. Remove the filter by pulling out the filter tray at the

side of the dehumidifier.

3. If you are using a carbon odor filter it needs to be

removed and discarded. NOTE: Carbon odor filters

used in this appliance will last approximately 30 days.

4. Rinse the screen thoroughly with cool water.

5. If you choose, insert a new carbon odor filter into the

filter frame.

6. Replace the filter tray by sliding it into the opening at

the side of the dehumidifier.

Replacement Carbon Odor Filter (Model HAPF36) is

available by calling 1-800-253-2764.

CLEANING AND MAINTAINANCE

1. Turn the dehumidifier to standby mode ( ) and

unplug it from the electrical outlet.

2. Carry the water reservoir to a sink or tub. Remove the

cover on the water reservoir and rinse reservoir with

warm water. Before operating again be sure the float

mechanism is positioned properly.

3. Wipe the reservoir and appliance dry with a clean

cloth or paper towel.

Figure 2

A. Backlight Button

B. LED Display

C. Room Humidity Display

D. Dehumidifier Setting Display

E. Tank Full Indicator

F. Low Battery Indicator

STORAGE INSTRUCTIONS

At the end of the season, please follow these instructions

to properly store your dehumidifier for use next season.

1. Turn the dehumidifier to standby mode ( ) and

unplug it from the electrical outlet.

2. Clean and dry the dehumidifier thoroughly as per the

cleaning instructions above.

3. Make sure all parts are dry before storing. Do not

store the appliance with any water in the reservoir.

4. If you are using a carbon odor filter, dispose of it at

this time. Do not store the appliance with the carbon

odor filter in place.

5. Store upright in a cool, dry location.

6. Order your new (HAPF36) filter so you will be pre-

pared for next season.

Figure. 5

igure 4

ow to Obtain Warranty Service

In the U.S.A.

If you have any questions regarding your product, this warranty,

or would like to obtain warranty service please visit our website

at www.bionaire.com or call 1 800-253-2764 and a convenient

service center address will be provided to you.

In Canada

If you have any questions regarding your product, this warranty,

or would like to obtain warranty service please visit our website

at www.bionaire.com or call 1 800-253-2764 and a convenient

service center address will be provided to you.

In the U.S.A., this warranty is offered by Sunbeam Products, Inc.

doing business as Jarden Consumer Solutions located in Boca

Raton, Florida 33431. In Canada, this warranty is offered by

Sunbeam Corporation (Canada) Limited doing business as

Jarden Consumer Solutions, located at 20 B Hereford Street,

Brampton, Ontario L6Y 0M1. If you have any other problem

or claim in connection with this product, please write out

Consumer Service Department

PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF

THESE ADDRESSES OR TO THE PLACE OF PURCHASE

Distributed by Sunbeam Products, Inc. doing business as Jarden

Consumer Solutions,Boca Raton, Florida 33431.

ENERGY STAR is a mark owned by the U.S. Government.

If you have any questions regarding your

product or would like to learn more about other

Bionaire product, please contact our Consumer

Service Department at 1-800-253-2764 or visit

our website at www.bionaire.com.

Printed in China

Summary of content (2 pages)

PAGE 1
DEHUMIDIFIER SAFETY QuieTech™ Dehumidifier MODEL BDQ25 Read instructions before operating. Retain for future reference. Instruction Leaflet ☎ INFO-LINE If after having read this leaflet, you have any questions or comments on your dehumidifier, call 1-800-253-2764 in North America. Step 2: Cut the hose to expose a Figure. 5 bare piece of rubber with no faucet connector attached. Step 3: Insert the hose around the bypass port located within this open area.
PAGE 2
SÉCURITÉ DU DÉSHUMIDIFICATEUR Déshumidificateur QuieTech™ MODÈLE BDQ25 Lisez les instructions avant d’utiliser l’appareil. Conservez-les pour référence future. Guide d’utilisation ☎ LIGNE DE RENSEIGNEMENTS Si, après avoir lu ce guide, vous avez des questions ou des commentaires concernant votre déshumidificateur, veuillez nous téléphoner au 1-800-253-2764 en Amérique du Nord.