User's Manual
Table Of Contents
- CHAPTER 1 - INTRODUCTION
- CHAPTER 2 - PLANNING THE INSTALLATION
- CHAPTER OVERVIEW
- 2.1 PLANNING THE INSTALLATION
- 2.1.1 RECOMENDED STEPS FOR A SUCCESSFUL INSTALLATION
- 2.1.2 REQUIREMENTS
- 2.1.3 UNPACK EQUIPMENT
- 2.1.4 CHOOSING THE INSTALL LOCATION
- 2.1.5 PLAN DEVICE NETWORK
- 2.1.6 CHOOSE NETWORK TYPE
- 2.1.7 CHOOSE POWER SOURCE
- CHAPTER 3 - INSTALL SOFTWARE
- CHAPTER OVERVIEW
- 3.1 SECUREADMIN LITE SERVER
- Figure 3-1 Install Menu
- Figure 3-2 SecureAdmin Lite Server Installation Wizard
- Figure 3-3 SecureAdmin Lite Server License Agreement
- Figure 3-4 SecureAdmin Lite Server Choose Destination Location
- Figure 3-5 Database Selection
- Figure 3-6 Connecting to SQL Server option
- 3.1.1 REPAIRING AN INSTALLATION OF SECUREADMIN LITE SERVER
- 3.1.2 UNINSTALLING SECUREADMIN LITE SERVER
- 3.1.3 UPGRADING AN INSTALLATION OF SECUREADMIN LITE SERVER
- 3.2 SECUREADMIN LITE CLIENT
- Figure 3-9 Menu
- Figure 3-10 InstallShield Wizard
- Figure 3-11 Welcome Screen
- Figure 3-12 SecureAdmin Lite Client License Agreement
- Figure 3-13 SecureAdmin Lite Client Choose Destination Location
- Figure 3-14 Fingerprint Placement Feedback Option Selection
- Figure 3-15 InstallShield Wizard Finished
- 3.2.1 MODIFYING AN INSTALLATION OF SECUREADMIN LITE CLIENT
- 3.2.2 REPAIRING AN INSTALLATION OF SECUREADMIN LITE CLIENT
- 3.2.3 UNINSTALLING SECUREADMIN LITE CLIENT
- 3.2.4 UPGRADING AN INSTALLATION OF SECUREADMIN LITE CLIENT
- CHAPTER 4 - INSTALL HARDWARE
- CHAPTER 5 - SYSTEM START-UP PROCEDURES
- CHAPTER 6 - CONFIGURE DEVICE
- CHAPTER 7 - MAINTENANCE AND CLEANING
- CHAPTER 8 - TROUBLESHOOTING
- CHAPTER OVERVIEW
- 8.1 INSTALLATION ERROR MESSAGES
- CHAPTER 9 - NOTICES
- GLOSSARY
Part # 430-4G-050-00-004
© 2011 - L-1 Identity Solutions Inc. All rights reserved
Planning the Installation
If you have any unresolved issues with the items on this list, contact L-1 Identity Solutions
Technical Support for additional information before beginning any installation.
WARNING
4G Lite devices should be installed by only a qualified
technician. If you are not qualified to perform an
installation task, call L-1 Identity Solutions Technical
Support or contact a qualified installer.
2.1.1 RECOMENDED STEPS FOR A SUCCESSFUL INSTALLATION
Every installation is unique. Sometimes the issues are well defined and can be handled in a
standard fashion; sometimes the issues are very specific and may not be immediately
recognizable.
L-1 Identity Solutions recommends following these steps for a successful installation:
Plan the installation - Choose the type of hardware required, decide if a
network is required, and decide on the location and number of required
devices.
Unpack all items - Unpack all items and check against the packing list.
Install network hardware components - Install the cabling and
components needed to run the system.
Install software - Install the software needed to set up the devices.
Preconfigure device - Connect the device to the USB cable, supply power
to the device, and preconfigure the device.
Mount devices - Mount the devices in their final locations
Power distribution and device hook up - Connect the device wiring via
the back panel.
Power-up procedure - Check the power connections and start the system
safely. Enroll users into the system (for user enrollment procedures).
Chapters 3 through 7 in this document present more information on these steps.
17