User's Manual
Table Of Contents
- CHAPTER 1 - INTRODUCTION
- CHAPTER 2 - PLANNING THE INSTALLATION
- CHAPTER OVERVIEW
- 2.1 PLANNING THE INSTALLATION
- 2.1.1 RECOMENDED STEPS FOR A SUCCESSFUL INSTALLATION
- 2.1.2 REQUIREMENTS
- 2.1.3 UNPACK EQUIPMENT
- 2.1.4 CHOOSING THE INSTALL LOCATION
- 2.1.5 PLAN DEVICE NETWORK
- 2.1.6 CHOOSE NETWORK TYPE
- 2.1.7 CHOOSE POWER SOURCE
- CHAPTER 3 - INSTALL SOFTWARE
- CHAPTER OVERVIEW
- 3.1 SECUREADMIN LITE SERVER
- Figure 3-1 Install Menu
- Figure 3-2 SecureAdmin Lite Server Installation Wizard
- Figure 3-3 SecureAdmin Lite Server License Agreement
- Figure 3-4 SecureAdmin Lite Server Choose Destination Location
- Figure 3-5 Database Selection
- Figure 3-6 Connecting to SQL Server option
- 3.1.1 REPAIRING AN INSTALLATION OF SECUREADMIN LITE SERVER
- 3.1.2 UNINSTALLING SECUREADMIN LITE SERVER
- 3.1.3 UPGRADING AN INSTALLATION OF SECUREADMIN LITE SERVER
- 3.2 SECUREADMIN LITE CLIENT
- Figure 3-9 Menu
- Figure 3-10 InstallShield Wizard
- Figure 3-11 Welcome Screen
- Figure 3-12 SecureAdmin Lite Client License Agreement
- Figure 3-13 SecureAdmin Lite Client Choose Destination Location
- Figure 3-14 Fingerprint Placement Feedback Option Selection
- Figure 3-15 InstallShield Wizard Finished
- 3.2.1 MODIFYING AN INSTALLATION OF SECUREADMIN LITE CLIENT
- 3.2.2 REPAIRING AN INSTALLATION OF SECUREADMIN LITE CLIENT
- 3.2.3 UNINSTALLING SECUREADMIN LITE CLIENT
- 3.2.4 UPGRADING AN INSTALLATION OF SECUREADMIN LITE CLIENT
- CHAPTER 4 - INSTALL HARDWARE
- CHAPTER 5 - SYSTEM START-UP PROCEDURES
- CHAPTER 6 - CONFIGURE DEVICE
- CHAPTER 7 - MAINTENANCE AND CLEANING
- CHAPTER 8 - TROUBLESHOOTING
- CHAPTER OVERVIEW
- 8.1 INSTALLATION ERROR MESSAGES
- CHAPTER 9 - NOTICES
- GLOSSARY
Part # 430-4G-050-00-004
© 2011 - L-1 Identity Solutions Inc. All rights reserved
Install Hardware
CHAPTER 4 - INSTALL HARDWARE
CHAPTER OVERVIEW
This chapter explains how to install a 4G Lite device, how to mount a wall plate, how to attach
a device to a wall plate, and how to make the required electrical connections to the device.
4.1 WALL-MOUNTING SCHEMES
The 4G V-Flex Lite, 4G CR-Pass devices are mounted, by use of a mounting plate, either
directly to a wall or to an electrical box recessed in the wall. The 4G V-Flex Lite and CR-Pass
devices can be flush mounted on a wall.
4G SecureControl devices are designed to be placed on the secure side of the installation
where it is only accessible by Administrators and not by users during normal operation (ie. in
the ceiling or wall-mounted), hence there is no mounting plate required.
4.2 INSTALLING A MOUNTING PLATE
The procedure for mounting a wall plate directly to a wall is as follows:
4.2.1 4G V-FLEX LITE AND 4G CR-PASS
1. Hold the mounting plate onto the wall in the desired location, trace the square hole that
will be cut out, and mark the mounting screw locations.
2. Cut out the square hole with a jigsaw or drywall saw. If the 4G V-Flex Lite device is to be
recess-mounted, cut out a hole in the drywall to accommodate the rear extension on the
device housing.
3. Drill holes for the nylon wall anchors and install them.
4. Fish wires through the wall to the square hole.
5. Align the hole in the wall plate with the hole in the wall.
6. Fasten the mounting plate to the nylon wall anchors in the wall with the provided screws.
45