User's Manual
Table Of Contents
- CHAPTER 1 - INTRODUCTION
- CHAPTER 2 - PLANNING THE INSTALLATION
- CHAPTER OVERVIEW
- 2.1 PLANNING THE INSTALLATION
- 2.1.1 RECOMENDED STEPS FOR A SUCCESSFUL INSTALLATION
- 2.1.2 REQUIREMENTS
- 2.1.3 UNPACK EQUIPMENT
- 2.1.4 CHOOSING THE INSTALL LOCATION
- 2.1.5 PLAN DEVICE NETWORK
- 2.1.6 CHOOSE NETWORK TYPE
- 2.1.7 CHOOSE POWER SOURCE
- CHAPTER 3 - INSTALL SOFTWARE
- CHAPTER OVERVIEW
- 3.1 SECUREADMIN LITE SERVER
- Figure 3-1 Launch screen – SecureAdmin Lite
- Figure 3-2 Launch screen –Installation 32-bit or 64-bit
- Figure 3-3 Install Menu
- Figure 3-4 SecureAdmin Lite Server Installation Wizard
- Figure 3-5 SecureAdmin Lite Server License Agreement
- Figure 3-6 SecureAdmin Lite Server Choose Destination Location
- Figure 3-7 Database Selection
- Figure 3-8 Connecting to SQL Server option
- 3.1.1 REPAIRING AN INSTALLATION OF SECUREADMIN LITE SERVER
- 3.1.2 UNINSTALLING SECUREADMIN LITE SERVER
- 3.1.3 UPGRADING AN INSTALLATION OF SECUREADMIN LITE SERVER
- 3.2 SECUREADMIN LITE CLIENT
- Figure 3-11 Menu
- Figure 3-12 InstallShield Wizard
- Figure 3-13 Welcome Screen
- Figure 3-14 SecureAdmin Lite Client License Agreement
- Figure 3-15 SecureAdmin Lite Client Choose Destination Location
- Figure 3-16 Fingerprint Placement Feedback Option Selection
- Figure 3-17 InstallShield Wizard Finished
- 3.2.1 MODIFYING AN INSTALLATION OF SECUREADMIN LITE CLIENT
- 3.2.2 REPAIRING AN INSTALLATION OF SECUREADMIN LITE CLIENT
- 3.2.3 UNINSTALLING SECUREADMIN LITE CLIENT
- 3.2.4 UPGRADING AN INSTALLATION OF SECUREADMIN LITE CLIENT
- CHAPTER 4 - INSTALL HARDWARE
- CHAPTER 5 - SYSTEM START-UP PROCEDURES
- CHAPTER 6 - CONFIGURE DEVICE
- CHAPTER 7 - MAINTENANCE AND CLEANING
- CHAPTER 8 - TROUBLESHOOTING
- CHAPTER OVERVIEW
- 8.1 INSTALLATION ERROR MESSAGES
- CHAPTER 9 - NOTICES
- GLOSSARY
Part # 430-4G-050-00-006
© 2011 - L-1 Identity Solutions Inc. All rights reserved
Planning the Installation
2.1.4 CHOOSING THE INSTALL LOCATION
2.1.4.1 4G CR Pass, 4G V-Flex Lite and 4G V-Station Lite
4G CR-Pass, 4G V-Flex Lite and 4G V-Station Lite devices are designed to mount on either a
single-gang electrical box or on any flat surface. Consult with local professionals regarding
any building and safety codes that might affect your installation. The correct mounting height
is shown below.
Factors to consider when determining the position of a device on the wall:
Proximity to other switch plates or fixtures (the device should ideally be
mounted in-line with other plates or fixtures)
Distance from the floor to the top of the device (L-1 Identity Solutions
recommends using a height between 48 and 54 inches).
The device should be mounted on the knob side of the door
Compliance with the Americans with Disabilities Act if in the United States.
Information about http://www.usdoj.gov.
Figure 2-1 Correct Mounting Height
2.1.4.2 4G SecureControl
4G SecureControl devices can be used in combination with any 4G Lite devices (up to
quantity of 4) for control of up to 2 physical doors. 4G SecureControl devices are also
designed to be placed on the secure side of the installation. 4G SecureControl must be
23