H55A+ Setup Manual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Chapter 1: Introduction ............................................................ 1 1.1 Before You Start ................................................................................ 1 1.2 Package Checklist ............................................................................. 1 1.3 Motherboard Features...................................................................... 2 1.4 1.5 Rear Panel Connectors .....................................................................
H55A+ CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation.
Motherboard Manual 1.3 MOTHERBOARD FEATURES SPEC CPU Chipset Supports Execute Disable Bit / Enhanced Intel Socket 1156 Intel Core i7 / i5 / i3/ Pentium processor Environment Control initiatives, Provides the most commonly used legacy Hardware Monitor Controller Super I/O functionality.
H55A+ SPEC Back Panel I/O Board Size Consumer IR Connector x1 Supports infrared function Power Connector (24pin) x1 Connects to Power supply Power Connector (4pin) x1 Connects to Power supply PS/2 Keyboard / Mouse x1 Connects to PS/2 Keyboard / Mouse HDMI Port x1 Connects to HDMI cable VGA Port x1 Connect to D-SUB monitor DVI-D Port x1 Connect to DVI monitor LAN Port x1 Connect to RJ-45 ethernet cable USB Port x4 Connect to USB devices Audio Jack x3 Provide Audio-In/Out and m
Motherboard Manual 1.5 MOTHERBOARD LAYOUT CPU_FAN1 USBKB1 ATXPWR2 HDMI1 DDR3_ B1 DDR3_ B2 CPU1 DDR3_ A1 DDR3_ A2 DVI 1 Socket 1156 VGA1 JUSBV1 RJ45USB1 AUDIO1 SYS_FAN2 F_AUDIO1 PEX1_1 ATXPWR1 PEX 16_1 LAN H55 PEX 16_2 CODEC PCI1 BIOS BAT1 Super I/O PCI2 SATA2 SATA1 SATA4 SATA3 SATA6 SATA5 JCMOS1 JUS BV2 JSPDIFOUT1 J_PRINT1 J_COM1 CIR1 F_USB 3 F_USB2 F_USB1 Note: ■ represents the 1st pin.
H55A+ CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Step 1: Pull the socket locking lever out from the socket and then raise the lever up. Step 2: Remove the Pin Cap.
Motherboard Manual Step 3: Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 4: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 5: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the CPU_FAN1 to complete the installation.
H55A+ 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different due to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.
Motherboard Manual 2.3 INSTALLING SYSTEM MEMORY 8 DDR3_B2 DDR3_B1 DDR3_A2 DDR3_A1 A. DDR3 module 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.
H55A+ B. Memory Capacity DIMM Socket Location DDR3 Module DDR3_A2 512MB/1GB/2GB/4GB DDR3_A1 512MB/1GB/2GB/4GB DDR3_B2 512MB/1GB/2GB/4GB DDR3_B1 512MB/1GB/2GB/4GB Total Memory Size Max is 16GB. C. Dual Channel Memory Installation Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table.
Motherboard Manual 2.4 CONNECTORS AND SLOTS SATA1~SATA6: Serial ATA Connectors The motherboard has a PCI to SATA Controller with 6channels SATA interface, it satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s. SA TA 2 SA TA1 SA TA 4 SA TA3 SA TA6 SA TA5 1 4 Pin 1 2 3 4 5 6 7 Assignment Ground TX+ TXGround RXRX+ Ground 7 ATXPWR1: ATX Power Source Connector This connector is for 24-pin power connector on the ATX power supply. Pin 13 14 15 16 17 18 19 20 21 22 23 24 10 Assignment +3.
H55A+ ATXPWR2: ATX Power Source Connector Connecting this connector provides +12V to CPU power circuit. 1 4 2 3 Pin 1 2 3 4 Assignment +12V +12V Ground Ground Note: Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors have been plugged-in. PCI1/PCI2: Peripheral Component Interconnect Slots This motherboard is equipped with 2 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards.
Motherboard Manual PEX16_1: PCI-Express Gen2 x16 Slot - PCI-Express 2.0 compliant. Maximum theoretical realized bandwidth of 8GB/s simultaneously per direction, for an aggregate of 16GB/s totally. PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins. PEX16_2: PCI-Express Gen2 x4 Slot - PCI-Express 2.0 compliant. Maximum theoretical realized bandwidth of 1GB/s simultaneously per direction, for an aggregate of 2GB/s totally. PEX1_1: PCI-Express Gen2 x1 Slot - PCI-Express 2.0 compliant.
H55A+ CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DETAIL SETTINGS PANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.
Motherboard Manual F_USB1/F_USB2/F_USB3: Headers for USB 2.0 Ports at Front Panel This motherboard provides 3 USB 2.0 headers, which allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader.
H55A+ F_AUDIO1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector, not AC’97. 10 9 2 1 Pin 1 2 3 4 5 6 7 8 9 10 Assignment Mic Left in Ground Mic Right in GPIO Right line in Jack Sense Front Sense Key Left line in Jack Sense JSPDIFOUT1: Digital Audio-out Connector This connector allows user to connect the PCI bracket SPDIF output header.
Motherboard Manual J_PRINT1: Printer Port Connector This header allows you to connector printer on the PC. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 2 26 1 25 Assignment Pin 14 15 16 17 18 19 20 21 22 23 24 25 26 -Strobe -ALF Data 0 -Error Data 1 -Init Data 2 -Scltin Data 3 Ground Data 4 Ground Data 5 Assignment Ground Data 6 Ground Data 7 Ground -ACK Ground Busy Ground PE Ground SCLT Key J_COM1: Serial port Connector The motherboard has a Serial Port Connector for connecting RS-232 Port.
H55A+ JCMOS1: Clear CMOS Header Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (Default). 1 1 3 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Procedures: 1. 2. 3. 4. 5. 6. Remove AC power line. Set the jumper to “Pin 2-3 close”. Wait for five seconds. Set the jumper to “Pin 1-2 close”. Power on the AC.
Motherboard Manual CHAPTER 4: USEFUL HELP 4.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.
H55A+ 4.2 SOFTWARE Installing Software 1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop. Double-click the icon to launch the utility.
Motherboard Manual After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click “Save”. Your system information will be saved to a .txt file. Open the saved .
H55A+ BIOS Update BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system. AWARD BIOS Show current BIOS information AMI BIOS Clear CMOS function (Only for AWARD BIOS) Save current BIOS to a .bin file Update BIOS with a BIOS file Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.
Motherboard Manual Before doing this, please download the proper BIOS file from the website. For AWARD BIOS, update BIOS procedure should be run with Clear CMOS function, so please check on Clear CMOS first. Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure.
H55A+ 4.3 EXTRA INFORMATION CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed.
Motherboard Manual BIO-Flasher BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive or floppy disk. The BIO-Flasher is built in the BIOS chip. To enter the utility, press during the Power-On Self Tests (POST) procedure while booting up. Updating BIOS with BIO-Flasher 1. Go to the website to download the latest BIOS file for the motherboard. 2. Then, save the BIOS file into a USB pen drive or a floppy disk. 3.
H55A+ 4.4 AMI BIOS BEEP CODE Boot Block Beep Codes Number of Beeps 1 2 3 4 5 7 10 11 12 13 Description No media present. (Insert diskette in floppy drive A:) “AMIBOOT.ROM” file not found in root directory of diskette in A: Insert next diskette if multiple diskettes are used for recovery Flash Programming successful File read error No Flash EPROM detected Flash Erase error Flash Program error “AMIBOOT.
Motherboard Manual 4.5 TROUBLESHOOTING Probable 1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive. Solution 1. 2. 3. Make sure power cable is securely plugged in. Replace cable. Contact technical support.
H55A+ This page is intentionally left blank.
Motherboard Manual APPENDIX: SPEC IN OTHER LANGUAGES GERMAN Spezifikationen Unterstützt Execute Disable Bit / Enhanced Intel Socket 1156 CPU SpeedStep® / Intel Architecture-64 / Extended Intel Core i7 / i5 / i3/ Pentium Prozessoren Memory 64 Technology / Virtualization Technology Chipsatz Intel H55 Umgebungskontrolle, ITE 8721 Bietet die häufig verwendeten alten Super Hardware-Überwachung Super E/A E/A-Funktionen.
H55A+ Spezifikationen Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion S/PDIF- Ausgangsanschluss x1 Unterstützt die digitale Audioausgabefunktion CPU-Lüfter-Sockel x1 CPU-Lüfterstromversorgungsanschluss (mit Smart Fan-Funktion) System-Lüfter-Sockel x2 "CMOS löschen"-Sockel x1 USB-Anschluss x3 System-Lüfter-Stromversorgungsanschluss Jeder Anschluss unterstützt 2 Fronttafel-USB-Anschlüsse Verbraucher-IR Ansc
Motherboard Manual FRENCH SPEC Prend en charge les technologies d'exécution de bit de UC Socket 1156 désactivation / Intel SpeedStep® optimisée/ Processeurs Intel Core i7 / i5 / i3/ Pentium d'architecture Intel 64 / de mémoire étendue 64 / de virtualisation Chipset Intel H55 ITE 8721 Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/S Moniteur de matériel patrimoniales la plus utilisée.
H55A+ SPEC Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant Connecteur de sortie S/PDIF x1 Prend en charge la fonction de sortie audio numérique Embase de ventilateur UC x1 Alimentation électrique du ventilateur UC (avec fonction de ventilateur intelligent) Embase de ventilateur système x2 Embase d'effacement CMOS x1 Connecteur USB x3 Alimentation électrique du ventilateur s
Motherboard Manual ITALIAN SPECIFICA CPU Chipset Socket 1156 Supporto di Execute Disable Bit / Enhanced Intel Processore Intel Core i7 / i5 / i3/ SpeedStep® / Architettura Intel 64 / Tecnologia Pentium Extended Memory 64 / Tecnologia V irtualization Intel H55 Funzioni di controllo dell’ambiente: ITE 8721 Fornisce le funzionalità legacy Super Monitoraggio hardware Super I/O I/O usate più comunemente.
H55A+ SPECIFICA Connettore output SPDIF x1 Collettore ventolina CPU x1 Supporta la funzione d’output audio digitale Alimentazione ventolina CPU (con funzione Smart Fan) Collettore ventolina sistema x2 Collettore cancellaz ione CMOS x1 Connettore USB x3 Alimentazione ventolina di sistema Ciascun connettore supporta 2 porte USB pannello frontale Connettore IR del consumatore x1 Connettore alimentazione x1 (24 pin) Connettore alimentazione x1 (4 pin) Tastiera / Mouse PS/2 x1 Porta HDMI x1 I
Motherboard Manual SPANISH Especificación Admite Bit de deshabilitación de ejecución / Intel SpeedStep® Mejorado / Intel Architecture-64 / Socket 1156 CPU Procesador Intel Core i7 / i5 / i3/ Pentium Tecnología Extended Memory 64 / Tecnología de virtualización Conjunto de chips Intel H55 Iniciativas de control de entorno, ITE 8721 Le ofrece las funcionalidades heredadas de Monitor hardware Súper E/S uso más común Súper E/S.
H55A+ Especificación Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal Conector de salida S/PDIF X1 Soporta función de salida de sonido digital Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con función Smart Fan) Cabecera de ventilador de sistema X2 Cabecera de borrado de CMOS X1 Conector USB X3 Conector de IR del consumidor X1 Conector de alimentación X1 Fuente de alimentación de ventilador de sistema Cada conector soporta 2 puer
Motherboard Manual PORTUGUESE ESPECIFICAÇÕES Suporta as tecnologias Execute Disable Bit / Enhanced CPU Socket 1156 Intel SpeedStep® / Intel Arquitecture -64 / Extended Processador Intel Core i7 / i5 / i3/ Pentium Memory 64 / Virtualization Chipset Intel H55 ITE 8721 Iniciativas para controlo do ambiente Proporciona as funcionalidades mais Monitorização do hardware Especificaçã o Super I/O utilizadas em termos da especificação Controlador/Monitor da velocidade da ventoinha Super I/O.
H55A+ ESPECIFICAÇÕES Conector do painel frontal x1 Para suporte de várias funções no painel frontal Conector de áudio frontal x1 Suporta a função de áudio no painel frontal Conector de saída S/PDIF x1 Suporta a saída de áudio digital Conector da ventoinha da CPU x1 Alimentação da ventoinha da CPU (com a função Smart Fan) Conector da ventoinha do sistema x2 Conector para limpeza do CMOS x1 Conector USB x3 Conector de IR do consumidor x1 Conector de alimentação x1 Alimentação da ventoinha
Motherboard Manual POLISH SPEC Obsługa Execute Disable Bit / Enhanced Intel Socket 1156 Procesor SpeedStep® / Intel Architecture-64 / Extended Procesor Intel Core i7 / i5 / i3/ Pentium Memory 64 Technology / Virtualization Technology Chipset Intel H55 Gniazda DDR3 DIMM x 4 Moduł pamięci DDR3 z trybem podwójnego kanału Pamięć Maks.
H55A+ SPEC Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowego wyjścia audio Złącze główkowe wentylatora Zasilanie wentylatora procesora (z funkcją Smart Fan) procesora x1 Złącze główkowe wentylatora Zasilanie wentylatora systemowego systemowego x2 Złącze główkowe kasowania CMOS x1 Każde złącze obsługuje 2 porty USB na panelu Złącze USB x3 przednim Złącze Konsument IR x1 Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinow
Motherboard Manual RUSSIAN СПЕЦ Поддержка технологий Execute Disable Bit / CPU (центральн Socket 1156 ый Enhanced Intel SpeedStep® / Intel Architecture-64 / Процессор Intel Core i7 / i5 / i3/ Pentium Extended Memory 64 Technology / технологии процессор) Набор микросхем виртуализация Intel H55 Слоты DDR3 DIMM x 4 Модуль памяти с двухканальным режимом DDR3 Основная Максимальная ёмкость памяти 16 ГБ Поддержка DDR3 1600(OC)/1333/1066/800 память Каждый модуль DIMM поддерживает Не поддерживает зареги
H55A+ СПЕЦ Разъём на лицевой панели x1 Поддержка устройств на лицевой панели Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели Разъём вывода для S/PDIF x1 Поддержка вывода цифровой звуковой функции Контактирующее приспособление Источник питания для вентилятора центрального вентилятора центрального процессора процессора (с функцией интеллектуального x1 вентилятора) Контактирующее приспособление вентилятора системы x2 Источник питания для вентилятора системы Открытое конт
Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت Socket 1156 Execute Disable Bit / Enhanced Intelﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت ﺑﺘﺮدد Intel Core i7 / i5 / i3/ Pentiumﻣﻌﺎﻟﺠﺎت SpeedStep® / Intel Architecture-64 / Extended یﺼﻞ إﻟﻰ Memory 64 Technology / Virtualization Technology وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ Intel H55 ﻓﺘﺤﺔ DDR3 DIMM ﻋﺪد4 ﻣﺰدوﺝﺔ اﻟﻘﻨﺎةDDR3وﺣﺪة ذاآﺮة ﺳﻌﺎت (OC)1600/1333/1066/800ﻣﻴﺠﺎ DDR3ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻥﻮع ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى 16ﺝﻴﺠﺎ ﺑﺎیﺖ اﻟﺬاآﺮة
H55A+ اﻟﻤﻮاﺻﻔﺎت ﻣﻨﻔﺬ ﺥﺮج S/PDIF ﻋﺪد 1 یﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ وﺹﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ ﻋﺪد 1 Smart Fanﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻣﻊ وﻇﻴﻔﺔ وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪد 2 ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم وﺹﻠﺔ ﻣﺴﺢ CMOS ﻋﺪد 1 ﻣﻨﻔﺬ USB ﻋﺪد 3 ﻣﻨﻔﺬ اﻷﺣﻤﺮ ﺗﺤ ﺖ ﻣﺴ ﺘﻬﻠﻜﺔ ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺑﻮس( ع دد 1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )4دﺑﺎﺑﻴﺲ( ﻋﺪد 1 ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ /ﻣﺎوس PS/2 ﻋﺪد 1 ﻣﻨﺎﻓﺬ HDMI ﻋﺪد 1 ﻣﻨﺎﻓﺬ
Motherboard Manual JAPANESE 仕様 Execute Disable Bit / Enhanced Intel SpeedStep® / Socket 1156 CPU Intel Architecture-64 / Extended Memory 64 Intel Core i7 / i5 / i3/ Pentium プロセッサ Technology / Virtualization Technologyをサポートします チップセット Intel H55 DDR3 DIMMスロット x 4 デュアル チャンネルモードDDR3メモリモジュール 最大メモリ容量16GB DDR3 1600(OC)/1333/1066/800をサポート メインメモリ 各DIMMは 512MB/1GB/2GB/4GB DDR3を 登録済みDIMMとECC DIMMはサポートされません サポート ITE 8721 環境コントロールイニシアチブ、 もっとも一般に使用されるレガシーSuper I/O H/Wモニター Super I/O 機能を採用しています。 ファン速度コントローラ/ モニター 低
H55A+ 仕様 S/PDIFアウトコネクタ x1 デジタルオーディオアウト機能をサポートします CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載) システムファンヘッダ x2 システムファン電源装置 CMOSクリアヘッダ x1 USBコネクタ x3 各コネクタは2つのフロントパネルUSBポートをサポートし ます 消費者IRコネクタ x1 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード / マウス x1 HDMIポート x1 VGAポート x1 DVI-Dポート x1 LANポート x1 USBポート x4 オーディオジャック x3 背面パネル I/O ボードサイズ 225mm (幅) X 295 mm (高さ) Biostarは事前のサポートなしにOSサポートを追加または削 OSサポート Windows XP / Vista / 7 除する権利を留保します。 2010/04/01 45