H6 1 M HV / H6 1 MG V/ H6 1 M LC2 S e tu p M a n u a l FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of Contents Chapter 1: Introduction ........................................ 1 1.1 1.2 1.3 1.4 1.5 Before You Start......................................................................................... 1 Package Checklist ..................................................................................... 1 Motherboard Features .............................................................................. 2 Rear Panel Connectors.....................................................................
H61M HV/ H61M GV/ H61ML C 2 CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: Prepare a dry and stable working environment with sufficient lighting. 1.2 Always disconnect the computer from power outlet before operation.
Motherboard Manual 1.
H61M HV/ H61M GV/ H61ML C 2 SPEC USB2.0 Connector x2 Each connector supports 2 front panel USB2.0 ports Serial Port Connector x1 Connects to RS-232 Port Power Connector (24pin) x1 Connects to Power supply Power Connector (4pin) x1 Connects to Power supply PS/2 Keyboard x1 Connects to PS/2 Keyboard PS/2 Mouse x1 Connects to PS/2 Mouse HDMI Port (H61MHV) x1 Connects to HDMI Display VGA Port x1 Connect to D-SUB monitor LAN port x1 Connect to RJ-45 ethernet cable USB2.
Motherboard Manual 1.5 MOTHERBOARD LAYOUT NOTE: ■ represents the 1st pin.
H61M HV/ H61M GV/ H61ML C 2 CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Notice: 1. 2. Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. The motherboard might equip with two different types of pin cap. Please refer below instruction to remove the pin cap.
Motherboard Manual Step 3: Hold processor with your thumb and index fingers, oriented as shown. Align the notches with the socket. Lower the processor straight down without tilting or sliding the processor in the socket. Step 4: Close the load plate. Pressing down on the load plate, close and engage the socket lever. Step 5: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the CPU_FAN1 to complete the installation.
H61M HV/ H61M GV/ H61ML C 2 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.
Motherboard Manual 2.3 INSTALLING SYSTEM MEMORY A. Memory Modules 1. 8 Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot.
H61M HV/ H61M GV/ H61ML C 2 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated. Note: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again. B. Memory Capacity DIMM Socket Location DDR3 Module DDR3_A1 512MB/1GB/2GB/4GB/8GB DDR3_B1 512MB/1GB/2GB/4GB/8GB Total Memory Size Max is 16GB. C.
Motherboard Manual 2.4 CONNECTORS AND SLOTS SATA1~SATA4: Serial ATA Connectors The motherboard has a PCI to SATA Controller with 4 channels SATA2 interface, it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s. Pin 1 2 3 4 5 6 7 Assignment Ground TX+ TXGround RXRX+ Ground ATXPWR2: ATX Power Source Connector This connector provides +12V to CPU power circuit.
H61M HV/ H61M GV/ H61ML C 2 ATXPWR1: ATX Power Source Connector This connector allows user to connect 24-pin power connector on the ATX power supply. Pin 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground Pin 1 2 3 4 5 6 7 8 9 10 11 12 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.
Motherboard Manual PEX16_1: PCI-Express Gen3 x16 Slot - PCI-Express 3.0 compliant. Maximum theoretical realized bandwidth of 16GB/s simultaneously per direction, for an aggregate of 32GB/s totally. PCI-E 3.0 is supported by Core i7-3xxx / i5-3xxx CPU. PEX1_1: PCI-Express Gen2 x1 Slot - 12 PCI-Express 2.0 compliant. Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.
H61M HV/ H61M GV/ H61ML C 2 CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DETAIL SETTINGS PANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.
Motherboard Manual F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel These headers allow user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC F_AUDIO1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel.
H61M HV/ H61M GV/ H61ML C 2 JCMOS1: Clear CMOS Header Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (default). 1 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Procedures: 1. 2. 3. 4. 5. 6. Remove AC power line. Set the jumper to “Pin 2-3 close”. Wait for five seconds. Set the jumper to “Pin 1-2 close”. Power on the AC.
Motherboard Manual CHAPTER 4: USEFUL HELP 4.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver DVD into your optical drive and install the driver for better system performance. You will see the following window after you insert the DVD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver DVD, please use file browser to locate and execute the file SETUP.
H61M HV/ H61M GV/ H61ML C 2 4.2 SOFTWARE Installing Software 1. Insert the Setup DVD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop.
Motherboard Manual After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click “Save”. Your system information will be saved to a .txt file. Open the saved .
H61M HV/ H61M GV/ H61ML C 2 BIOS Update BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system. Show current BIOS information Update BIOS from the Internet Save current BIOS to a .bin file Update BIOS with a BIOS file Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.) Then click Save.
Motherboard Manual Before doing this, please download the proper BIOS file from the website. Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure. After the BIOS Backup procedure, the open dialog will show for requesting the BIOS file which is going to be updated. Please choose the proper BIOS file for updating, then click on Open.
H61M HV/ H61M GV/ H61ML C 2 4.3 EXTRA INFORMATION CPU Overheated If the system shuts down automatically after system is powered on for seconds, the phenomenon means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3.
Motherboard Manual 4.4 AMI BIOS BEEP CODE Boot Block Beep Codes Number of Beeps 1 2 3 4 5 7 10 11 12 13 Description No media present. (Insert diskette in floppy drive A:) “AMIBOOT.ROM” file not found in root directory of diskette in A: Insert next diskette if multiple diskettes are used for recovery Flash Programming successful File read error No Flash EPROM detected Flash Erase error Flash Program error “AMIBOOT.
H61M HV/ H61M GV/ H61ML C 2 4.5 TROUBLESHOOTING Probable 1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive. System only boots from an optical drive.
Motherboard Manual APPENDIX: SPEC IN OTHER LANGUAGES GERMAN Spezifikationen Unterstützt Execute Disable Bit / Enhanced Intel Socket 1155 CPU SpeedStep® / Intel Architecture-64 / Extended Intel Core i7 / i5 / i3 / Pentium / Celeron Memory 64 Technology / Virtualization Technology / Prozessoren Hyper Threading Chipsatz Intel H61 IT8772E Super E/A Umgebungskontrolle, Bietet die häufig verwendeten alten Super Hardware-Überwachung E/A-Funktionen.
H61M HV/ H61M GV/ H61ML C 2 Spezifikationen System-Lüfter-Sockel x1 "CMOS löschen"-Sockel x1 USB2.0-Anschluss x2 System-Lüfter-Stromversorgungsanschluss Jeder Anschluss unterstützt 2 Fronttafel-USB2.0-Anschlüsse Rückseiten-E /A Serieller Anschluss x1 Stromanschluss (24-polig) x1 Stromanschluss (4-polig) x1 PS/2-Tastatur x1 PS/2-Maus x1 HDMI-Anschluss (H61MHV) x1 VGA-Anschluss x1 LAN-Anschluss x1 USB2.
Motherboard Manual FRENCH SPEC Prend en charge les technologies d'exécution de bit Socket 1155 UC de désactivation / Intel SpeedStep® optimisée/ Processeurs Intel Core i7 / i5 / i3 / Pentium / d'architecture Intel 64 / de mémoire étendue 64 / de Celeron virtualisation / Hyper Threading Chipset Intel H61 IT8772E Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/S Moniteur de matériel patrimoniales la plus utilisée.
H61M HV/ H61M GV/ H61ML C 2 SPEC Embase de ventilateur système x1 Embase d'effacement CMOS x1 Connecteur USB2.0 x2 Alimentation électrique du ventilateur système Chaque connecteur prend en charge 2 ports USB2.0 de panneau avant Port série x1 Connecteur d'alimentation x1 (24 broches) Connecteur d'alimentation x1 (4 broches) Clavier PS/2 x1 Souris PS/2 x1 E/S du Port HDMI (H61MHV) x1 panneau Port VGA x1 arrière Port LAN x1 Port USB2.
Motherboard Manual ITALIAN SPECIFICA Supporto di Execute Disable Bit / Enhanced Socket 1155 CPU Intel SpeedStep® / Architettura Intel 64 / Processore Intel Core i7 / i5 / i3 / Tecnologia Extended Memory 64 / Tecnologia Pentium / Celeron Virtualization / Hyper Threading Chipset Intel H61 IT8772E Super I/O Memoria principale Funzioni di controllo dell’ambiente: Fornisce le funzionalità legacy Super I/O Monitoraggio hardware usate più comunemente.
H61M HV/ H61M GV/ H61ML C 2 SPECIFICA Collettore cancellaz ione CMOS x1 Connettore USB2.0 x2 Ciascun connettore supporta 2 porte USB2.0 pannello frontale Porta seriale x1 Connettore alimentazione x1 (24 pin) Connettore alimentazione x1 (4 pin) I/O pannello posteriore Tastiera PS/2 x1 Mouse PS/2 x1 Porta HDMI (H61MHV) x1 Porta VGA x1 Porta LAN x1 Porta USB2.
Motherboard Manual SPANISH Especificación Admite Bit de deshabilitación de ejecución / Intel Socket 1155 CPU SpeedStep® Mejorado / Intel Architecture-64 / Procesador Intel Core i7 / i5 / i3 / Pentium / Tecnología Extended Memory 64 / Tecnología de Celeron virtualización / Hyper Threading Conjunto de chips Intel H61 IT8772E Iniciativas de control de entorno, Le ofrece las funcionalidades heredadas de Monitor hardware uso más común Súper E/S.
H61M HV/ H61M GV/ H61ML C 2 Especificación Cabecera de borrado de CMOS X1 Conector USB2.0 X2 Puerto serie X1 Conector de alimentación X1 Cada conector soporta 2 puertos USB2.0 frontales (24 patillas) Conector de alimentación X1 (4 patillas) Teclado PS/2 X1 Ratón PS/2 X1 Panel Ratón HDMI (H61MHV) X1 trasero de Puerto VGA X1 E/S Puerto de red local X1 Puerto USB2.0 X4 Conector de sonido X3 Tamaño de la placa 170 mm. (A) X 226 Mm.
Motherboard Manual PORTUGUESE ESPECIFICAÇÕES Suporta as tecnologias Execute Disable Bit / Socket 1155 CPU Processador Intel Core i7 / i5 / i3 / Pentium / Celeron Chipset o Super I/O / Extended Memory 64 / Virtualization / Hyper Threading Intel H61 IT8772E Especificaçã Enhanced Intel SpeedStep® / Intel Arquitecture -64 Iniciativas para controlo do ambiente Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O.
H61M HV/ H61M GV/ H61ML C 2 ESPECIFICAÇÕES Conector da ventoinha do sistema x1 Conector para limpeza do CMOS x1 Conector USB2.0 x2 Porta série x1 Conector de alimentação x1 Alimentação da ventoinha do sistema Cada conector suporta 2 portas USB2.0 no painel frontal (24 pinos) Conector de alimentação x1 (4 pinos) Entradas/S aídas no painel traseiro Tamanho da placa Teclado PS/2 x1 Rato PS/2 x1 Porta HDMI (H61MHV) x1 Porta VGA x1 Porta LAN x1 Porta USB2.
Motherboard Manual POLISH SPEC Obsługa Execute Disable Bit / Enhanced Intel Socket 1155 Procesor SpeedStep® / Intel Architecture-64 / Extended Procesor Intel Core i7 / i5 / i3 / Pentium / Memory 64 Technology / Virtualization Technology / Celeron Hyper Threading Chipset Intel H61 Gniazda DDR3 DIMM x 2 Moduł pamięci DDR3 z trybem podwójnego kanału Pamięć Maks.
H61M HV/ H61M GV/ H61ML C 2 SPEC Złącze główkowe wentylatora Zasilanie wentylatora systemowego systemowego x1 Złącze główkowe kasowania CMOS x1 Każde złącze obsługuje 2 porty USB2.0 na panelu Złącze USB2.0 x2 przednim Port szeregowy x1 Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinowe) x1 Klawiatura PS/2 x1 Mysz PS/2 x1 Port HDMI (H61MHV) x1 Port VGA x1 Port LAN x1 Port USB2.
Motherboard Manual RUSSIAN СПЕЦ CPU (центральн ый Поддержка технологий Execute Disable Bit / Socket 1155 Процессор Intel Core i7 / i5 / i3 / Pentium / Celeron микросхем / Extended Memory 64 Technology / технологии виртуализация / Hyper Threading процессор) Набор Enhanced Intel SpeedStep® / Intel Architecture-64 Intel H61 Слоты DDR3 DIMM x 2 Модуль памяти с двухканальным режимом DDR3 Основная Максимальная ёмкость памяти 16 ГБ Поддержка DDR3 1066 / 1333 / 1600 память Каждый модуль DIMM поддержив
H61M HV/ H61M GV/ H61ML C 2 СПЕЦ Контактирующее приспособление вентилятора системы x1 Источник питания для вентилятора системы Открытое контактирующее Задняя панель средств ввода-выв ода приспособление CMOS x1 USB2.0-разъём x2 Последовательный порт x1 Разъем питания (24 вывод) x1 Разъем питания (4 вывод) x1 Клавиатура PS/2 x1 Мышь PS/2 x1 Порт HDMI (H61MHV) x1 Порт VGA x1 Порт LAN x1 USB2.0-порт x4 Каждый разъём поддерживает 2 USB2.
Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت Execute Disable Bit / Enhanced Intelﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت Socket 1155 SpeedStep® / Intel Architecture-64 / Extended وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ Intel Core i7 / i5 / i3 / Pentium /ﻣﻌﺎﻟﺠﺎت Memory 64 Technology / Virtualization Technology / ﺑﺘﺮدد یﺼﻞ إﻟﻰ Celeron Hyper Threading ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ Intel H61 ﻓﺘﺤﺔ DDR3 DIMM ﻣﺰدوﺝﺔ اﻟﻘﻨﺎةDDR3وﺣﺪة ذاآﺮة 1066 / 1366 / ﺳ ﻌﺎت DDR3ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻥﻮع ﻋﺪد2 ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى 16ﺝ
H61M HV/ H61M GV/ H61ML C 2 اﻟﻤﻮاﺻﻔﺎت وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪد 1 وﺹﻠﺔ ﻣﺴﺢ CMOS ﻋﺪد 1 ﻣﻨﻔﺬ USB2.0 ﻋﺪد 2 ﻣﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ ﻋﺪد1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺑﻮس( ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )4دﺑﺎﺑﻴﺲ( ﻋﺪد 1 ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ PS/2 ﻋﺪد 1 ﻣﺎوس PS/2 ﻋﺪد 1 ﻣﻨﺎﻓﺬ )HDMI (H61MHV ﻋﺪد 1 ﻣﻨﺎﻓﺬ VGA ﻋﺪد 1 ﻣﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ ﻋﺪد 1 ﻣﻨﺎﻓﺬ USB2.
Motherboard Manual JAPANESE 仕様 Execute Disable Bit / Enhanced Intel SpeedStep® / Socket 1155 CPU Intel Architecture-64 / Extended Memory 64 Intel Core i7 / i5 / i3 / Pentium / Celeron プロ Technology / Virtualization Technology / Hyper セッサ Threadingをサポートします チップセット Intel H61 DDR3 DIMMスロット x 2 デュアル チャンネルモードDDR3メモリモジュール 最大メモリ容量16GB DDR3 1066 / 1333 / 1600をサポート メインメモリ 各DIMMは 512MB/1GB/2GB/4GB/8GB DDR3 登録済みDIMMとECC DIMMはサポートされません をサポート Super I/O SATA 2 IT8772E 環境コントロールイニシアチブ、 もっとも一般に使用されるレガシーSuper I/O機
H61M HV/ H61M GV/ H61ML C 2 仕様 各コネクタは2つのフロントパネルUSB2.0ポートをサポ USB2.0コネクタ x2 ートします シリアルポート x1 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 PS/2マウス x1 HDMIポート(H61MHV) x1 VGAポート x1 LANポート x1 USB2.