H61MLV S etup Man ual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Chapter 1: Introduction ........................................ 1 1.1 1.2 1.3 1.4 1.5 Before You Start......................................................................................... 1 Package Checklist ..................................................................................... 1 Motherboard Features.............................................................................. 2 Rear Panel Connectors......................................................................
H6 1 M LV CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: 1.2 Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation.
Motherboard Manual 1.
H6 1 M LV SPEC Printer Port Connector x1 Each connector supports 1 Printer port Serial Port Connector x1 Connects to RS-232 Port Power Connector (24pin) x1 Connects to Power supply Power Connector (4pin) x1 Connects to Power supply PS/2 Keyboard x1 Connects to PS/2 Keyboard PS/2 Mouse x1 Connects to PS/2 Mouse Rear Panel VGA Port x1 Connect to D-SUB monitor I/O LAN port x1 Connect to RJ-45 ethernet cable USB2.0 Port x4 Connect to USB2.
Motherboard Manual 1.5 MOTHERBOARD LAYOUT KBMS1 CPU_FAN1 ATX PWR2 CPU1 DDR3_B1 VGA1 DDR3_A1 Socket 1155 SYS_FAN1 USB1 RJ45USB1 BAT1 AUDIO1 F_AUDIO1 CODEC Super I/O ATXPWR1 PEX16_1 BIOS LAN H61 PEX1_1 SATA2 JCMOS1 F_USB1 SATA3 J_PRINT1 F_USB2 J_COM1 Note: ■ represents the 1st pin.
H6 1 M LV CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Step 1: Pull the socket locking lever out from the socket and then raise the lever up. Step 2: Remove the Pin Cap.
Motherboard Manual Step 3: Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 4: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 5: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the CPU_FAN1 to complete the installation.
H6 1 M LV 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.
Motherboard Manual 2.3 INSTALLING SYSTEM MEMORY 8 DDR3_B1 DDR3_A1 A. Memory Modules 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.
H6 1 M LV B. Memory Capacity DIMM Socket Location DDR3 Module DDR3_A1 512MB/1GB/2GB/4GB/8GB DDR3_B1 512MB/1GB/2GB/4GB/8GB Total Memory Size Max is 16GB. C. Dual Channel Memory Installation Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table. Dual Channel Status DDR3_A1 DDR3_B1 Disabled O X Disabled X O Enabled O O (O means memory installed; X, not installed.
Motherboard Manual 2.4 CONNECTORS AND SLOTS SATA1~SATA4: Serial ATA Connectors The motherboard has a PCI to SATA Controller with 4 channels SATA2 interface, it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s. Pin 1 2 3 4 5 6 7 SATA1 SATA2 SATA3 SATA4 7 4 Assignment Ground TX+ TXGround RXRX+ Ground 1 ATXPWR2: ATX Power Source Connector This connector provides +12V to CPU power circuit.
H6 1 M LV ATXPWR1: ATX Power Source Connector This connector allows user to connect 24-pin power connector on the ATX power supply. Pin 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground 12 24 1 13 Pin 1 2 3 4 5 6 7 8 9 10 11 12 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.
Motherboard Manual PEX16_1: PCI-Express Gen2 x16 Slot - PCI-Express 2.0 compliant. Maximum theoretical realized bandwidth of 8GB/s simultaneously per direction, for an aggregate of 16GB/s totally. PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins. 2X bandwidth over the PCI-Express 1.1 architecture. PEX1_1: PCI-Express Gen2 x1 Slot - PCI-Express 2.0 compliant. Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.
H6 1 M LV CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DETAIL SETTINGS PANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.
Motherboard Manual F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel These headers allow user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. Pin 1 2 3 4 5 6 7 8 9 10 F_USB1 F_USB2 2 10 1 9 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC F_AUDIO1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel.
H6 1 M LV JCMOS1: Clear CMOS Header Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (default). 1 3 Pin 2-3 Close: Clear CMOS data. 1 3 ※ Clear CMOS Procedures: 1. 2. 3. 4. 5. 6. Remove AC power line. Set the jumper to “Pin 2-3 close”. Wait for five seconds. Set the jumper to “Pin 1-2 close”. Power on the AC.
Motherboard Manual J_PRINT1: Printer Port Connector This header allows you to connector printer on the PC.
H6 1 M LV CHAPTER 4: USEFUL HELP 4.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.
Motherboard Manual 4.2 SOFTWARE Installing Software 1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop.
H6 1 M LV After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click “Save”. Your system information will be saved to a .txt file. Open the saved .
Motherboard Manual BIOS Update BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system. Show current BIOS information Update BIOS from the Internet Update BIOS with a BIOS file Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.) Then click Save. 20 Save current BIOS to a .
H6 1 M LV Before doing this, please download the proper BIOS file from the website. Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure. After the BIOS Backup procedure, the open dialog will show for requesting the BIOS file which is going to be updated. Please choose the proper BIOS file for updating, then click on Open.
Motherboard Manual 4.3 EXTRA INFORMATION CPU Overheated If the system shuts down automatically after system is powered on for seconds, the phenomenon means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3.
H6 1 M LV 4.4 AMI BIOS BEEP CODE Boot Block Beep Codes Number of Beeps 1 2 3 4 5 7 10 11 12 13 Description No media present. (Insert diskette in floppy drive A:) “AMIBOOT.ROM” file not found in root directory of diskette in A: Insert next diskette if multiple diskettes are used for recovery Flash Programming successful File read error No Flash EPROM detected Flash Erase error Flash Program error “AMIBOOT.
Motherboard Manual 4.5 TROUBLESHOOTING Probable 1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive. Solution 1. 2. 3. Make sure power cable is securely plugged in. Replace cable. Contact technical support.
H6 1 M LV This page is intentionally left blank.
Motherboard Manual APPENDIX: SPEC IN OTHER LANGUAGES GERMAN Spezifikationen Unterstützt Execute Disable Bit / Enhanced Intel Socket 1155 CPU SpeedStep® / Intel Architecture-64 / Extended Intel Core i7 / i5 / i3 / Pentium / Celeron Memory 64 Technology / Virtualization Technology / Prozessoren Hyper Threading Chipsatz Intel H61 IT8728 Super E/A Umgebungskontrolle, Bietet die häufig verwendeten alten Super Hardware-Überwachung E/A-Funktionen.
H6 1 M LV Spezifikationen System-Lüfter-Sockel x1 "CMOS löschen"-Sockel x1 USB2.0-Anschluss x2 System-Lüfter-Stromversorgungsanschluss Jeder Anschluss unterstützt 2 Fronttafel-USB2.0-Anschlüsse Druckeranschluss Anschluss x1 Serieller Anschluss x1 Stromanschluss (24-polig) x1 Stromanschluss (4-polig) x1 PS/2-Tastatur x1 PS/2-Maus x1 Rückseiten-E VGA-Anschluss x1 /A LAN-Anschluss x1 USB2.
Motherboard Manual FRENCH SPEC Prend en charge les technologies d'exécution de bit Socket 1155 UC de désactivation / Intel SpeedStep® optimisée/ Processeurs Intel Core i7 / i5 / i3 / Pentium / d'architecture Intel 64 / de mémoire étendue 64 / de Celeron virtualisation / Hyper Threading Chipset Intel H61 IT8728 Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/S Moniteur de matériel patrimoniales la plus utilisée.
H6 1 M LV SPEC Embase de ventilateur système x1 Embase d'effacement CMOS x1 Connecteur USB2.0 x2 Alimentation électrique du ventilateur système Chaque connecteur prend en charge 2 ports USB2.0 de panneau avant Connecteur de Port d'imprimante x1 Port série x1 Connecteur d'alimentation x1 Chaque connector prend en charge 1 Port d'imprimante (24 broches) Connecteur d'alimentation x1 (4 broches) E/S du panneau arrière Clavier PS/2 x1 Souris PS/2 x1 Port VGA x1 Port LAN x1 Port USB2.
Motherboard Manual ITALIAN SPECIFICA Supporto di Execute Disable Bit / Enhanced Socket 1155 CPU Intel SpeedStep® / Architettura Intel 64 / Processore Intel Core i7 / i5 / i3 / Tecnologia Extended Memory 64 / Tecnologia Pentium / Celeron Virtualization / Hyper Threading Chipset Intel H61 IT8728 Super I/O Memoria principale Funzioni di controllo dell’ambiente: Fornisce le funzionalità legacy Super I/O Monitoraggio hardware usate più comunemente.
H6 1 M LV SPECIFICA Collettore cancellaz ione CMOS x1 Connettore USB2.0 x2 Ciascun connettore supporta 2 porte USB2.0 pannello frontale Connettore Porta stampante x1 Porta seriale x1 Connettore alimentazione x1 Ciascun connettore supporta 1 Porta stampante (24 pin) Connettore alimentazione x1 (4 pin) Tastiera PS/2 x1 Mouse PS/2 x1 Porta VGA x1 posteriore Porta LAN x1 I/O pannello Dimension i scheda Porta USB2.
Motherboard Manual SPANISH Especificación Admite Bit de deshabilitación de ejecución / Intel Socket 1155 CPU SpeedStep® Mejorado / Intel Architecture-64 / Procesador Intel Core i7 / i5 / i3 / Pentium / Tecnología Extended Memory 64 / Tecnología de Celeron virtualización / Hyper Threading Conjunto de chips Intel H61 IT8728 Iniciativas de control de entorno, Le ofrece las funcionalidades heredadas de Monitor hardware uso más común Súper E/S.
H6 1 M LV Especificación Cabecera de borrado de CMOS X1 Conector USB2.0 X2 Cada conector soporta 2 puertos USB2.0 frontales Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora Puerto serie X1 Conector de alimentación X1 (24 patillas) Conector de alimentación X1 (4 patillas) Panel trasero de E/S Teclado PS/2 X1 Ratón PS/2 X1 Puerto VGA X1 Puerto de red local X1 Puerto USB2.0 X4 Conector de sonido X3 Tamaño de la placa 170 mm. (A) X 226 Mm.
Motherboard Manual PORTUGUESE ESPECIFICAÇÕES Suporta as tecnologias Execute Disable Bit / Socket 1155 CPU Processador Intel Core i7 / i5 / i3 / Pentium / Celeron Chipset o Super I/O / Extended Memory 64 / Virtualization / Hyper Threading Intel H61 IT8728 Especificaçã Enhanced Intel SpeedStep® / Intel Arquitecture -64 Iniciativas para controlo do ambiente Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O.
H6 1 M LV ESPECIFICAÇÕES Conector da ventoinha do sistema x1 Conector para limpeza do CMOS x1 Conector USB2.0 x2 Conector da para impressora x1 Porta série x1 Conector de alimentação x1 Alimentação da ventoinha do sistema Cada conector suporta 2 portas USB2.0 no painel frontal Cada conector suporta 1 Porta para impressora (24 pinos) Conector de alimentação x1 (4 pinos) Teclado PS/2 x1 Entradas/S Rato PS/2 x1 aídas no Porta VGA x1 painel Porta LAN x1 traseiro Porta USB2.
Motherboard Manual POLISH SPEC Obsługa Execute Disable Bit / Enhanced Intel Socket 1155 Procesor SpeedStep® / Intel Architecture-64 / Extended Procesor Intel Core i7 / i5 / i3 / Pentium / Memory 64 Technology / Virtualization Technology / Celeron Hyper Threading Chipset Intel H61 Gniazda DDR3 DIMM x 2 Moduł pamięci DDR3 z trybem podwójnego kanału Pamięć Maks.
H6 1 M LV SPEC Złącze główkowe kasowania CMOS x1 Każde złącze obsługuje 2 porty USB2.0 na panelu Złącze USB2.0 x2 przednim Złącze Port drukarki x1 Port szeregowy x1 Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinowe) x1 Klawiatura PS/2 x1 Mysz PS/2 x1 Back Panel Port VGA x1 I/O Port LAN x1 Port USB2.
Motherboard Manual RUSSIAN СПЕЦ CPU (центральн ый Поддержка технологий Execute Disable Bit / Socket 1155 Процессор Intel Core i7 / i5 / i3 / Pentium / Celeron микросхем / Extended Memory 64 Technology / технологии виртуализация / Hyper Threading процессор) Набор Enhanced Intel SpeedStep® / Intel Architecture-64 Intel H61 Слоты DDR3 DIMM x 2 Модуль памяти с двухканальным режимом DDR3 Основная Максимальная ёмкость памяти 16 ГБ Поддержка DDR3 1066 / 1333 память Каждый модуль DIMM поддерживает Не
H6 1 M LV СПЕЦ Контактирующее приспособление вентилятора системы x1 Источник питания для вентилятора системы Открытое контактирующее приспособление CMOS x1 USB2.
Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت Execute Disable Bit / Enhanced Intelﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت Socket 1155 SpeedStep® / Intel Architecture-64 / Extended وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ Intel Core i7 / i5 / i3 / Pentium /ﻣﻌﺎﻟﺠﺎت Memory 64 Technology / Virtualization Technology / ﺑﺘﺮدد یﺼﻞ إﻟﻰ Celeron Hyper Threading ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ Intel H61 ﻓﺘﺤﺔ DDR3 DIMM ﻋﺪد2 ﻣﺰدوﺝﺔ اﻟﻘﻨﺎةDDR3وﺣﺪة ذاآﺮة ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى 16ﺝﻴﺠﺎ ﺑﺎیﺖ اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ ﺳﻌﺎت 1333 / 1066ﻣﻴﺠﺎ ﺑﺎی
H6 1 M LV اﻟﻤﻮاﺻﻔﺎت وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪد 1 وﺹﻠﺔ ﻣﺴﺢ CMOS ﻋﺪد 1 ﻣﻨﻔﺬ USB2.0 ﻋﺪد 2 ﻣﻨﻔﺬ ﻃﺎﺑﻌﺔ ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ ﻋﺪد1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺑﻮس( ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )4دﺑﺎﺑﻴﺲ( ﻋﺪد 1 ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ PS/2 ﻋﺪد 1 ﻣﺎوس PS/2 ﻋﺪد 1 ﻣﻨﺎﻓﺬ دﺥﻞ/ﺥﺮج ﻣﻨﺎﻓﺬ VGA ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲ USB2.0ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ ﻋﺪد 1 اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ ﻣﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ ﻋﺪد 1 ﻣﻨﺎﻓﺬ USB2.
Motherboard Manual JAPANESE 仕様 Execute Disable Bit / Enhanced Intel SpeedStep® / Socket 1155 CPU Intel Architecture-64 / Extended Memory 64 Intel Core i7 / i5 / i3 / Pentium / Celeron プロ Technology / Virtualization Technology / Hyper セッサ Threadingをサポートします チップセット Intel H61 DDR3 DIMMスロット x 2 デュアル チャンネルモードDDR3メモリモジュール 最大メモリ容量16GB DDR3 1066 / 1333 をサポート メインメモリ 各DIMMは 512MB/1GB/2GB/4GB/8GB DDR3 登録済みDIMMとECC DIMMはサポートされません をサポート Super I/O SATA 2 IT8728 環境コントロールイニシアチブ、 もっとも一般に使用されるレガシーSuper I/O機 H/Wモニター
H6 1 M LV 仕様 各コネクタは2つのフロントパネルUSB2.0ポートをサポ USB2.0コネクタ x2 ートします プリンタポートコネクタ x1 シリアルポート x1 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 PS/2マウス x1 背面パネル VGAポート x1 I/O LANポート x1 USB2.