M M77N NC CD P Prroo FCC Information and Copyright This equipment has been tested and found to c omply with the limits of a C lass B digital device, pursuant to Part 15 of the FCC Rules . T hese limits are designed to provide reasonable protection agains t harmful interference in a residential installation. This equipment generates , uses and can radiate radio frequency energy and, if not ins talled and used in accordance with the instructions, may c ause harmful interference to radio communications .
C Coonntteenntt LAYOUT OF M7NCD PRO..................................................................... 1 COMPONENT INDEX............................................................................. 2 ENGLIS H................................................................................................... 3 M7NCD Pro Features..................................................................................3 Package contents..................................................................................
Layout of M7NCD Pro ※NOTE: ●represents the f irst pin.
Component Index A. 5V/5VSB S el ection for Keybo ard and mouse ( JKBV1) B. Power Source Selection for USB (JUSBV2) L. Front USB Header (JUSB 1) M. Front USB Header (JUSB 2) N. Power Source Selection for USB (JUSBV4) C. Back Panel Connector O. W ake On LAN Header (JW OL1) D. Frequency Selection (JCLK3) P. S ystem FAN Header (JSF AN1) E. North Bridge Fan Header (JNFAN1) Q. Clear CMOS Fun ction (JCMOS) F. Accel erated Graphi cs Port Slot (AGP1) R. Case Open Connector (JC 1) S.
English M7NCD Pro Features A. Hardware CPU Prov ides Socket-462. ® Supports the AMD processor up to XP 3200+. Front Side Bus at 266/333/400 MHz. Chipset North Bridge: nFORCE2 SPP. South Bridge: nMCP. oHigh Speed 800Mb/s Hyper-Transport interface to the MCP. Main Memory Supports up to 3 DDR devices. Supports 266/333/400MHz (without ECC) DDR dev ices. High perf ormance 128 bit DDR400 Twin Bank Memory Architecture. Maximum memory size of 3GB. Super I/O Chip: Winbond W83627HF.
PS/2 mouse and PS/2 keyboard. 2 USB2.0 ports. b.Front Side 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes. 4 USB2.0 ports. 1 front audio header. Dimensions ATX Form Factor: 24.4cm X 30.4cm (W X L) B. BIOS & Software BIOS Award legal Bios. APM1.2. ACPI. USB Function. Software TM TM TM TM Supports CPU Savior , 9th Touch , FLASHER™, WinFlasher , StudioFun! TM (optional) and Watchdog .
CPU Installation Step1: Pull the lever sideway s away from the socket and then raise the lever up to a 90-degree angle. Step2: Look for the white dot/cut edge. The white dot/cut edge should point towards the lev er piv ot. The CPU will f it only in the correct orientation. Step3: Hold the CPU down f irmly, and then close the lever. Step4: Put the CPU f an on the CPU and buckle it. Connect the CPU fan power cable to the JCFAN1. This completes the installation.
North Bridge Fan Header: JNFAN1 1 JNFAN1 Pin No. 1 2 Assignment Ground +12V DDR DIMM Modules: DIMMB1-2, DIMMA1 For Dual-channel DDR (128-bit) high performance, at least 2 or more DIMM modules must be installed. (It has to be the combination of DIMMA and DIMMB.) With only one DIMM installed, the memory performs only at 64-bit. DRAM Access Time: 2.5V Unbuffered DDR 266/333/400 MHz Type required.
Jumpers, Headers, Connectors & Slots Floppy Disk Connector: FDD1 The motherboard provides a standard f loppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the prov ided f loppy drive ribbon cables. Hard Disk Connectors: IDE1/ IDE2 The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/ 66/ 100/ 133 functionality. It has two HDD connectors IDE1 (primary) and IDE2 (secondary).
Front Panel Connector: JPANEL1 P WR_LED S LP JPANEL1 ON/ OF F (+) (+) (-) IR 24 2 1 23 (+) (-) S PK Pin 1 Assignment +5V 3 HLED R ST IR Function Pin 2 Assignment Sleep Control Function Sleep NA Speaker 4 Ground Button 5 NA Connector 6 NA NA 7 Speaker 8 Power LED (+) POWER 9 HDD LED (+) Hard Drive 10 Power LED (+) LED 11 HDD LED (-) LED 12 Power LED (-) 13 Ground Power Button Reset Control Reset Button 14 15 16 Ground 17 NA 18 KEY 19 NA IrDA 20 KE
Power S ource Selection for Keyboard/ Mouse: JKBV1 JKBV1 Assignment Description +5V for key board and mouse 3 +5V 1 Pin 1-2 close 3 +5V Standby Voltage 1 PS/2 Mouse and PS/2 Keyboard are powered with +5V standby v oltage Pin 2-3 close Note: In order to power-on keyboard and mouse function, “JKBV1” jumper cap should be placed on pin 2-3.
Clear CMOS Jumper: JCMOS JCMOS Assignment 3 Normal Operation (default) 1 Pin 1-2 Close 3 Clear CMOS Data 1 Pin 2-3 Close The following procedures are for resetting the BIOS passw ord. It is important to follow these instructions closely. ※ Clear CM OS Procedures: 1. Remov e AC power line. 2. Set the jumper to “Pin 2-3 Close”. 3. Wait for fiv e seconds. 4. Set the jumper to “Pin 1-2 Close”. 5. Power on the AC. 6. Reset y our desired password or clear the CMOS data.
Front Panel Audio Header: JF_AUDIO1 9 10 1 2 JF_AUDIO1 Pin Assignment Mic In/ Center Pin 1 2 Assignment Ground 3 Mic Power/ Bass 4 Audio Power 5 Right Line Out/ Speaker Out Right 6 Right Line Out/ Speaker Out Right 7 Reserv ed 8 Key 9 Left Line Out/ Speaker Out Left 10 Left Line Out/ Speaker Out Left S ystem Operation Mode: JCLK3 JCLK3 Assignment User Mode (default) 1 (133/ 166 MHz) Pin 1-2 Close Saf e mode 1 (100 MHz) Pin 1-2 Open Note: When ov erclock function failed and syst
Back Panel Connectors 12
Deutsch Spezifik ationen von M7NCD Pro A. Hardware CPU Unterstützung für Sockel 462. ® Unterstützung für den AMD Prozessor bis zu XP 3200+. FSB mit 266/333/400 MHz. Chipsatz Northbridge: nFORCE2 SPP. Southbridge: MCP. Hauptspeicher Unterstützung für 3 DDR Geräte. Unterstützung für 266/333/400MHz (ohne ECC) DDR Geräte. 128-Bit High-Performance DDR400 mit der Twin-Bank Architektur. Die maximale Speichergröße ist 3GB. Super I/O Chip: Winbond W83627HF. Slots Fünf 32-Bit PCI-Bus-Slots. Ein AGP-Slot: n AGP3.
2 USB2.0-Ports. b.Vorderseite 1 Floppy-Port mit Unterstützung für 2 Diskettenlauf werke.(360KB, 720KB, 1.2MB, 1.44MB und 2.88MB) 4 USB2.0-Ports. 1 Audio-Header für die Vonderseite Abmessungen ATX Form-Factor: 24.4 X 30.4cm (W X L) B. BIOS & Software BIOS Award legal Bios. APM1.2. ACPI. USB Funktion. Software TM TM TM Unterstützung für CPU Sav ior , 9th Touch , FLASHER™, WinFlasher , TM TM StudioFun! (optional) and Watchdog .
Einstellung der Jumper Die Abbildung verdeutlicht, wie Jumper eingestellt werden. Pins werden durch die Jumper-Kappe v erdeckt, ist der Jumper ”geschlossen”. Keine Pins werden durch die Jumper-Kappe verdeckt, ist der Jumper “geöffnet”. Die Abbiildung zeigt einen 3-Pin Jumper dessen Pin1 und Pin2 ”geschlossen“ sind, bzw. es bef indet sich eine Jumper-Kappe auf diesen beiden Pins.
CPU-Lüfter Headers: JCFAN1 1 JCFAN1 Pin 1 2 3 Belegung Masse +12V Sensor S ystem-Lüfter Headers: JS FAN1 1 JSFAN1 Pin 1 2 3 Belegung Masse +12V Sensor Northbridge-Lüfter Header: JNFAN1 1 JNFAN1 Pin 1 2 Belegung Masse +12V DDR-DIMM- Modules: DIMMB1-2, DIMMA1 Für Dual-Kanal DDR (128-Bit) High-Performance, muss man mindestens 2 oder mehr DIMM-Module installieren. (Es ist unbedingt, daß man DIMMA mit DIMMB als ein Paar benutzt.
Installation von DDR-Modul 1. Öff nen Sie einen DIMM-Slots, indem Sie die seitlich Chips nach außen drücken. Richten Sie das DIMM-Modul so über dem Slot aus, dass das Modul mit der Kerbe in den Slot passt. 2. Drücken Sie das DIMM-Modul in den Slot, bis die seitlichen Clips zuschnappen und das Modul f est sitzt. Jumpers, Headers, Anschlüsse & Slots Diskettenanschluss: FDD1 Das Motherboard enthält einen standardmäßigen Diskettenanschluss, der 360K-, 720K-, 1.2M-, 1.44M- und 2.88M-Disketten unterstützt.
Anschlüsse für die Vorderseite: JPANEL1 P WR_LED S LP (+) (+) (-) ON/ OF F IR 24 2 JPANEL1 23 1 (+) (-) S PK HLED R ST IR Pin 1 Belegung +5V Funktion Pin 2 Belegung Sleep Control Funktion Schlaf en- 3 Kein Lautsprecher 4 Masse Knopf 5 Kein Anschluss 7 Lautsprecher 9 HDD LED (+) 11 6 Kein Kein 8 Power LED (+) Power- 10 Power LED (+) LED HDD LED (-) Festplatte LED 12 Power LED (-) 13 15 Masse Reset Control ZurücksetznKnopf 14 16 Power-Knopf Masse Power-On Knop
S tromversorgungsanschluss: JATXPWER1 10 1 20 11 JATXPWR1 PIN 1 2 Belegung +3.3V +3.3V PIN 11 12 Belegung +3.
Auswahl von Stromsversorgungsmodi für US B: JUS BV1/ JUS BV2/JUS BV4 JUSBV1/JUSBV2/ JUSBV4 1 Beschreibung Funktion +5V JUSBV1: 5V für JUSB1 3 JUSBV2: 5V für JUSBLAN1 Pin 1-2 geschlossen JUSBV4: 5V für JUSB2 +5V_SB 1 JUSBV1: JUSB1 ist aktiviert durch die reserv ierte 5V Spannang 3 JUSBV2: JUSBLAN1 ist aktiviert durch die reserv ierte 5V Spannang Pin 2-3 geschlossen JUSBV4: JUSB2 ist aktiviert durch die reserv ierte 5V Spannang Anmerkung: Um die “pow er-on by USB-Geräte” Funktion zu behandeln,
※ Prozeß zum Löschen des CM OS: 1. Ausschalten Sie den AC-Netzstecker. 2. Lassen Sie Pin 2-3 v on JCOMS1 geshclossen sein. 3. Bitte warten Sie 15 Sekunden. 4. Lassen Sie Pin 1-2 v on JCOMS1 geshclossen sein. 5. Schließen Sie den AC-Netzstecker an. 6. Zurücksetzen Sie das Kennwort nach ihrem Wille oder löschen Sie die CMOS-Daten.
S ystem Operation Modus: JCLK3 JCLK3 Assignment Benutzer Modus (def ault) 1 (133/ 166 MHz) Pin 1-2 Geöffnet Sicherheit Modus 1 (100 MHz) Pin 1-2 Geschlossen Anmerkung: Wenn “Überspanng Funktion” nicht gelungen ist f olgen Sie bitte die Instruktion darunter: 1. Bitte vausschalton Sie den AC-Notzstecker. 2. Lassen Sie Pin 1-2 v on JCLK3 geschlossen sein. 3. Schließen Sie den AC-Notzstecker an. 4. Betreten Sie “CMOS Setup Menü” und wählen sie Default-Setting. 5. Ausschalten Sie den AC-Netzstecker wieder.
Watchdog Technology It is important to know that when overclocking, the system can be at a v ulnerable state. Theref ore, the BIOSTAR Watchdog Technology was designed to protect y our PC under dangerous over-clock situations. Any ov er-clocking that reaches the threshold settings, the Watchdog Technology will disable y our system from rebooting in the BIOS setting. Under this circumstance, please power off your PC. After that, press and power on y our system simultaneously to restart your system.
StudioFun! Introduction StudioFun! is a media-player based on optimized GNU/Linux distribution. It plays DVD, VCD, MP3, Audio CD and various other known f ile formats. You can take snapshots of video and customize the sav ed images as screensavers. Y ou can also store the images on USB mass storage dev ci es like flash disks and USB f loppy disks. Hardware Requirements The supported hardware list of StudioFun! grows up ev ery day. So please check the hwreq.
Installation This option will do the basic installation of the distribution. The installation works on pre-installed windows or GNU/Linux distribution. On selecting the ’installation’ option the installer boots and displays a dialog box indicating the space required and waits f or a confirmation. Selecting Ok will continue the installation while selecting Cancel will terminate the installation and reboot the machine.
Recovery In case of a MBR corruption, this option should be used. It will automatically probe the hard disk master boot record and f ind out the installed operating system(s). On success it will re-install the boot loader with correct options in the MBR. Any custom boot loader option specified from other GNU/Linux installations will get ov er written by the newly probed one. Booting to StudioFun! After Installation is ov er, remove the CD f rom the CD-ROM and restart the machine.
After complete boot up, you get to the main Desktop screen. The f ollowing section is a complete description of the Desktop application. Desktop This is the main shell of the StudioFun software. It basically comprises of two categories, one is the main "media control" part and the other is the "control panel". Media control The media control part of the Desktop has the f ollowing controls: 1. VCD This control will glow whenev er a VCD is detected in a DVD/CD-ROM driv e.
present in the DVD/CD-ROM driv e. 2. DVD This control will glow whenev er a DVD is detected in a DVD drive. The DVD will be auto-played only when it is put in to the drive when the Desktop (StudioFun! shell) is up and running, otherwise, the control will simply glow to inform the user about a DVD present in the DVD/CD-ROM. 3. MP3 This control will glow whenev er a MP3 is detected in a DVD/CD-ROM driv e.
1. Select Region Clicking this icon will inv oke the application for selection DVD region settings. Ref er to section 5.2 Select DVD Region application for more details. 2. S creensaver Clicking this icon will inv oke the screensav er application. Ref er to section 5.3 Screensaver f or more details. 3. Display Settings Clicking this icon will inv oke the application for changing the screen resolutions. Refer to section 5.4, Display Settings f or more details . 4.
Software Details XIN E XINE is a multimedia play er. It plays back Audio CD, DVD, and VCD. It also decodes multimedia files like AVI, MOV, WMV, and MP3 from local disk driv es. It interprets many of the most common multimedia f ormats available - and some of the uncommon f ormats, too. • Features of Xine a. Skinnable GUI b. Navigation controls (seekin g, p ause, fast, slow, next chap ter, etc) c. On Screen Display (OSD) features d. DVD and external subtitles e.
a. f. MPEG-Video (.mp v, .m2v) g. MPEG-Audio (.mp 2, .mp 3) h. WAV (.wav) Video Codecs i. MPEG 1/2 j. MPEG 4 (aka Op enDivX) k. M S MPEG 4 Chap ter 5: Software Details 10 l. Windows Media Video 7 m. M otion JPEG • Remote Control support. a. Infrared interface b. User-friendly • Usage of S tudioFun! with CelomaChrome skin a. Select VCD button to p lay a VCD disc b. Select DVD button to p lay a DVD disc c. Select CDDA button to p lay a Audio cd d.
l. m. n. o. p. q. r. s. j. Select hide button to hide the control p anel of the play er k. Select menu button to use menu’s while p lay ing DVD l. Select control button to adjust brightness / color Select setup button to modify the settings of the p layer Select f.
Screensaver S creensaver The xscreensaver daemon waits until the keyboard and mouse hav e been idle for a period, and then runs a graphics demo chosen at random. The demo is terminated as soon as there is any mouse or keyboard activ ity. The xscreensav er-demo program is the graphical user interf ace to xscreensaver. It lets y ou tune the v arious parameters used by the xscreensaver daemon, and browse through the graphics demos.
2. Only one Screen Saver: When user chooses this option, screensaver displays only one graphics demo. 3. Blank Screen Only: When user chooses this option, screensaver only blanks the screen instead of displaying the graphics demo. 4. Disable Screen Saver: When user chooses this option, screensaver is disabled. • Various Graphics Demos XScreensav er comes with various screensaver Chbg: This screensaver displays the images stored in StudioFun! the time gap between images is 5 seconds.
three resolutions. • 640x480 • 800x600 • 1024x768 The current resolution of the Display will be selected by default. It requires restart of the StudioFun to reflect the changes made. File Manager Overview File manger is an utility to copy f iles from deferent devices to hard disk and v ice versa. User can copy f iles from dev ices such as, f loppy, cdrom and f lashdisk to hard disk. And also f rom hard disk to floppy and flashdisk.
36
Trouble Shooting PROBABLE SOLUTION No power to the system at all Power light don’t * Make sure power cable is securely plugged in illuminate, fan inside power supply does not turn * Replace cable on. Indicator light on keyboard does not turn on * Contact technical support PROBABLE SOLUTION System inoperative. Keyboard lights are on, * Using even pressure on both ends of the power indicator il ghts are lit, hard drive is DIMM, press down firmly until the module snaps into place. spinning.
Problemlösung MÖGLICHE URSACHE LÖSUNG Das System hat keine Spannungsversorgung. * Versichern Sie sich, dass das Stromkabel richtig Die Stromanzeige leuchtet nic ht, der Lüfter im angebracht ist Inneren der Stromversorgung wird nicht * Ersetzen Sie das Stromkabel eingeschaltet. T astaturleuchten sind nicht an. * Wenden Sie sich an Ihre Kundendienststelle MÖGLICHE URSACHE LÖSUNG Das System funktioniert nicht.
05/21/2003 39
M7NCD Pro BIOS Setup BIOS Setup........................................................................................1 1 Main Menu..................................................................................................... 3 2 Standard CMOS Features .............................................................................. 6 3 Advanced BIOS Features............................................................................... 9 4 Advanced Chipset Features.....................................
M7NCD Pro BIOS Setup BIOS Setup Introduction This manual discussed Award™ Setup program built into the ROM BIOS. The Setup program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM so that it retains the Setup information when the power is turned off. The Award BIOS™ installed in your computer system’s ROM (Read Only Memory) is a custom version of an industry standard BIOS. This means that it supports AMD® processor input/output system.
M7NCD Pro BIOS Setup PCI Bus Support This AWARD BIOS also supports Version 2.1 of the Intel PCI (Peripheral Component Interconnect) local bus specification. DRAM Support DDR SDRAM (Double Data Rate Synchronous DRAM) are supported. Supported CPUs This AWARD BIOS supports the AMD® CPU. Using Setup In general, you use the arrow keys to highlight items, press to select, use the and keys to change entries, press for help and press to quit.
M7NCD Pro BIOS Setup 1 Main Menu Once you enter Award BIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions. Use the arrow keys to select among the items and press to accept and enter the sub-menu. !! WARNING !! The information about BIOS defaults on manual (Figure 1,2,3,4,5,6,7,8,9) is just for reference, please refer to the BIOS installed on board, for update information. Figure 1.
M7NCD Pro BIOS Setup Input/ Output features. Power Management Setup This submenu allows you to configure the power management features. PnP/PCI Configurations This submenu allows you to configure certain “Plug and Play” and PCI options. PC Health Status This submenu allows you to monitor the hardware of your system. Frequency/ Voltage Control This submenu allows you to change CPU Vcore Voltage and CPU/PCI clock. (However, this function is strongly recommended not to use.
M7NCD Pro BIOS Setup Set User Password If the Supervisor Password is not set, then the User Password will function in the same way as the Supervisor Password. If the Supervisor Password is set and the User Password is set, the “User” will only be able to view configurations but will not be able to change them. Save & Exit Setup Save all configuration changes to CMOS(memory) and exit setup. Confirmation message will be displayed before proceeding.
M7NCD Pro BIOS Setup 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the or keys to select the value you want in each item. Figure 2.
M7NCD Pro BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu. Item Options Date mm : dd : yy Set the system date. Note that the ‘Day’ automatically changes when you set the date. Time hh : mm : ss Set the clock. IDE Primary Master Options are in its sub menu. Press to enter the sub menu of detailed options IDE Primary Slave Options are in its sub menu. Press to enter the sub menu of detailed options.
M7NCD Pro BIOS Setup Item Halt On Options Description All Errors Select the situation in which No Errors you want the BIOS to stop All, but Keyboard All, but Diskette the POST process and notify you. All, but Disk/ Key Base Memory N/A Displays the amount of conventional memory detected during boot up. Extended Memory N/A Displays the amount of extended memory detected during boot up. Total Memory N/A Displays the total memory available in the system.
M7NCD Pro BIOS Setup 3 Advanced BIOS Features Figure 3. Advanced BIOS Setup Boot Seq & Floppy Setup First/ Second/ Third/ Boot Other Device These BIOS attempt to load the operating system from the device in the sequence selected in these items. The Choices: Floppy, LS120, HDD-0, SCSI, CDROM, HDD-1, HDD-2, HDD-3, ZIP100, USB-FDD, USB-ZIP, USB-CDROM, USB-HDD, LAN, HPT370, Disabled, Enabled. Swap Floppy Drive For systems with two floppy drives, this option allows you to swap logical drive assignments.
M7NCD Pro BIOS Setup Cache Setup CPU Internal Cache Depending on the CPU/chipset in use, you may be able to increase memory access time with this option. The Choices: Enabled (default) Enable cache. Disabled Disable cache. External Cache This option you to enable or disable “Level 2” secondary cache on the CPU, which may improve performance. The Choices: Enabled (default) Enable cache. Disabled Disable cache.
M7NCD Pro BIOS Setup Typematic Rate (Chars/Sec) Sets the rate at which a keystroke is repeated when you hold the key down. The Choices: 6 (default), 8,10,12,15,20,24,30. Typematic Delay (Msec) Sets the delay time after the key is held down before it begins to repeat the keystroke. The Choices: 250 (default), 500,750,1000. Security Option This option will enable only individuals with passwords to bring the system online and/or to use the CMOS Setup Utility.
M7NCD Pro BIOS Setup 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset installed on your system. This chipset manage bus speeds and access to system memory resources, such as DRAM. It also coordinates communications with the PCI bus. The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly. Figure 4.
M7NCD Pro BIOS Setup FSB Frequency This item allows you to select the FSB Frequency. The Choices: 100MHz (Default), 133MHz, 166MHz, 200MHz. CPU Interface Optimal (Default) This item allows you to use the most stable CPU/ FSB parameters. Aggressive This item allows you to use overclocked CPU/ FSB parameters. Turbo Memory Frequency Select “Auto” for best performance. The Choices: By SPD (Default), 50%, 60%, 66%, 75%, 80%, 83%, 100%, 120%, 125%, 133%, 150%, 166%, 200%, Auto.
M7NCD Pro BIOS Setup CAS Latency This item allows you to set System Performance to “Optimal” to use the delay recommended by the DIMM’s manufacturer. The Choices: 2.5 (Default), 2.0, 3.0. FSB Spread Spectrum This item allows you to select the FSB Spread Spectrum. The Choices: 0.50% (Default). AGP Spread Spectrum This item allows you to select the AGP Spread Spectrum. The Choices: Disabled (Default). Frame Buffer Size This item allows you to select the Frame Buffer Size.
M7NCD Pro BIOS Setup 12.5%. System BIOS Cacheable Selecting Enabled allows you caching of the system BIOS ROM at F0000h~FFFFFh, resulting a better system performance. However, if any program writes to this memory area, a system error may result. The Choices: Enabled, Disabled (default). Video RAM Cacheable Enabling this option allows caching of the video RAM, resulting a better system performance. However, if any program writes to this memory area, a system error may result.
M7NCD Pro BIOS Setup 5 Integrated Peripherals Figure 5. Integrated Peripherals IDE Function Setup The chipset contains a PCI IDE interface with support for two IDE channels. Select “Enabled” to activate the first and / or second IDE interface. If you install a primary and / or secondary add-in IDE interface, select “Disabled” to deactivate an interface.
M7NCD Pro BIOS Setup IDE Primary / Secondary Master / Slave UDMA Ultra DMA/100 functionality can be implemented if it is supported by the IDE hard drives in your system. As well, your operating environment requires a DMA driver (Windows 95 OSR2 or a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/100, select Auto to enable BIOS support. The Choices: Auto (default), Disabled.
M7NCD Pro BIOS Setup This item allows you to decide to active whether PCI Slot or on-chip VGA first. The Choices: Onboard/AGP, PCI Solt (default). OnChip USB This item allows you to set the onchip USB. The Choices: V1.1+V2.0 (default), Disabled, V1.1. USB Keyboard Support The default value is Disabled. Enabled Disabled (default) Enable USB Keyboard Support. Disable USB Keyboard Support.
M7NCD Pro BIOS Setup permits transmission in one direction only at a time. The Choices: Half (default), Full. Use IR Pins Consult your IR peripheral documentation to select the correct setting of the TxD and RxD signals. The Choices: IR-Rx2Tx2 (default), RxD2, TxD2. Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O address. The Choices: 378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled. Parallel Port Mode The default value is SPP.
M7NCD Pro BIOS Setup 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up/power down features. Figure 6. Power Management Setup ACPI function This item displays the status of the Advanced Configuration and Power Management (ACPI). The Choices: Enabled (default), Disabled. ACPI Suspend Type The item allows you to select the suspend type under the ACPI operating system.
M7NCD Pro BIOS Setup There are four options of Power Management, three of which have fixed mode settings Min. Power Saving Minimum power management. Suspend Mode = 1 hr. HDD Power Down = 15 min Max. Power Saving Maximum power management only available for sl CPU’s. Suspend Mode = 1 min. HDD Power Down = 1 min. User Defined (default) Allows you to set each mode individually. When not disabled, each of the ranges are from 1 min. to 1 hr. except for HDD Power Down which ranges from 1 min. to 15 min.
M7NCD Pro BIOS Setup Soft-Off state when the system has “hung.” The Choices: Delay 4 Sec, Instant-Off (default). WOL (PME#) From Soft-Off This item allows you to enable or disable the WOL (PME#) From Soft-Off. The Choices: Disabled (Default), Enabled. WOR (RI#) From Soft-Off This item allows you to enable or disable the WOR (RI#) From Soft-Off. The Choices: Disabled (Default), Enabled. S3 Resume by USB (Win98) This item allows you to enable or disable S3 Resume by USB (Win98).
M7NCD Pro BIOS Setup 7 PnP/PCI Configurations This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. Figure 7.
M7NCD Pro BIOS Setup non-PnP ISA add-on cards. PCI / ISA PnP signifies that a resource is assigned to the PCI Bus or provides for ISA PnP add-on cards and peripherals. The Choices: Disabled (default), Enabled. Resources Controlled By By Choosing “Auto(ESCD)” (default), the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral.By Choosing “Manual”, the user will need to assign IRQ & DMA for add-on cards.
M7NCD Pro BIOS Setup 8 PC Health Status Figure 8. PC Health Status Current CPU Temperature Show you the current CPU temperature. Current SYSFAN Speed This field displays the current SYSFAN speed. Current CPUFAN Speed This field displays the current CPUFAN speed. CPU Vcore/ AGP Vcore/ +3.3V/ +12V/ -12V/ -5V Detect the system’s voltage status automatically. Show H/W Monitor in POST If you computer contain a monitoring system, it will show PC health status during POST stage.
M7NCD Pro BIOS Setup Chassis Open Warning This item allows you to enable or disable Chassis Open Warning beep. The Choices: Disabled (Default), Enabled.
M7NCD Pro BIOS Setup 9 Frequency Control Figure 9. Frequency Control CPU Voltage Regulator This item allows you to select CPU Voltage Regulator. The Choices: Default (default), -0.025V, -0.050V, -0.075V, -0.100V, +0.025V, +0.050V, +0.075V. AGP Voltage Regulator This item allows you to select AGP Voltage Regulator. The Choices: 1.5V (Default), 1.6V, 1.7V, 1.8V. DRAM Voltage Regulator This item allows you to select DRAM Voltage Regulator. The Choices: 2.5V (Default), 2.6V, 2.7V, 2.8V.