TH61 ITX Setup Man ual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Chapter 1: Introduction ........................................ 1 1.1 1.2 1.3 1.4 1.5 Before You Start......................................................................................... 1 Package Checklist ..................................................................................... 1 Motherboard Features.............................................................................. 2 Rear Panel Connectors......................................................................
TH6 1 I TX CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: 1.2 Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation.
Motherboard Manual 1.
TH6 1 I TX SPEC USB3.0 Connector x1 Each connector supports 2 front panel USB3.
Motherboard Manual 1.5 MOTHERBOARD LAYOUT ATXPWR 1 SATA1 SATA3 SATA2 SATA4 JPANEL1 U SB1 F_USB1 JCMOS1 JFRONT_USB3_1 LED_D1 L ED_D2 BAT1 CIR1 BIOS H61 USB_KBMS1 Socket 1155 DVI VGA CPU 1 SYS_FAN1 CPU_FAN1 JATXPWR2 AU DIO2 F_AUDIO1 CODEC PEX16_1 Note: ■ represents the 1st pin.
TH6 1 I TX CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Step 1: Pull the socket locking lever out from the socket and then raise the lever up. Step 2: Remove the Pin Cap.
Motherboard Manual Step 3: Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 4: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 5: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the CPU_FAN1 to complete the installation.
TH6 1 I TX 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.
Motherboard Manual 2.3 INSTALLING SYSTEM MEMORY DDR3_A1 DDR3_B1 A. Memory Modules 8 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.
TH6 1 I TX B. Memory Capacity DIMM Socket Location DDR3 Module Total Memory Size DDR3_A1 512MB/1GB/2GB/4GB/8GB DDR3_B1 512MB/1GB/2GB/4GB/8GB Max is 16GB. C. Dual Channel Memory Installation Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table. Dual Channel Status DDR3_A1 DDR3_B1 Disabled O X Disabled X O Enabled O O (O means memory installed, X means memory not installed.
Motherboard Manual 2.4 CONNECTORS AND SLOTS SATA1~SATA4: Serial ATA2 Connectors The motherboard has a PCI to SATA Controller with 4 channels SATA2 interface, it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s. SATA1 SATA3 SATA2 SATA4 7 4 1 Pin 1 2 3 4 5 6 7 Assignment Ground TX+ TXGround RXRX+ Ground PEX16_1: PCI-Express Gen2 x16 Slot - PCI-Express 2.0 compliant. Maximum theoretical realized bandwidth of 8GB/s simultaneously per direction, for an aggregate of 16GB/s totally.
TH6 1 I TX ATXPWR1: ATX Power Source Connector This connector allows user to connect 24-pin power connector on the ATX power supply. Pin 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground 24 13 12 1 Pin 1 2 3 4 5 6 7 8 9 10 11 12 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.3V JATXPWR2: ATX Power Source Connector This connector provides +12V to CPU power circuit.
Motherboard Manual CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened Pin closed Pin1-2 closed 3.2 DETAIL SETTINGS JPANEL1: Front Panel Header This 10-pin header includes Power-on, Reset, HDD LED, and Power LED connection. It allows user to connect the system case’s front panel switch functions.
TH6 1 I TX F_USB1: Header for USB 2.0 Ports at Front Panel This header allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. 9 1 10 2 Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC JFRONT_USB3_1: Header for USB 3.
Motherboard Manual F_AUDIO1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable. 10 9 2 1 Pin 1 2 3 4 5 6 7 8 9 10 Assignment Mic Left in Ground Mic Right in GPIO Right line in Jack Sense Front Sense Key Left line in Jack Sense On-Board LED Indicators There are 2 LED indicators on the motherboard showing system status.
TH6 1 I TX JCMOS1: Clear CMOS Header Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard. 3 3 1 1 Pin 1-2 Close: Normal Operation (default). 3 1 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Procedures: 1. 2. 3. 4. 5. 6. Remove AC power line. Set the jumper to “Pin 2-3 close”. Wait for five seconds. Set the jumper to “Pin 1-2 close”. Power on the AC.
Motherboard Manual CHAPTER 4: USEFUL HELP 4.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.
TH6 1 I TX 4.2 SOFTWARE Installing Software 1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop. Double-click the icon to launch the utility.
Motherboard Manual After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click “Save”. Your system information will be saved to a .txt file. Open the saved .
TH6 1 I TX BIOS Update BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system. Show current BIOS information Update BIOS from the Internet Save current BIOS to a .bin file Update BIOS with a BIOS file Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.) Then click Save.
Motherboard Manual Before doing this, please download the proper BIOS file from the website. Click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure. After the BIOS Backup procedure, the open dialog will show for requesting the BIOS file which is going to be updated. Please choose the proper BIOS file for updating, then click on Open.
TH6 1 I TX 4.3 EXTRA INFORMATION CPU Overheated If the system shuts down automatically after system is powered on for seconds, the phenomenon means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3.
Motherboard Manual 4.4 AMI BIOS BEEP CODE Boot Block Beep Codes Number of Beeps 1 2 3 4 5 7 10 11 12 13 Description No media present. (Insert diskette in floppy drive A:) “AMIBOOT.ROM” file not found in root directory of diskette in A: Insert next diskette if multiple diskettes are used for recovery Flash Programming successful File read error No Flash EPROM detected Flash Erase error Flash Program error “AMIBOOT.
TH6 1 I TX 4.5 TROUBLESHOOTING Probable 1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive. Solution 1. 2. 3. Make sure power cable is securely plugged in. Replace cable. Contact technical support.
Motherboard Manual APPENDIX: SPEC IN OTHER LANGUAGES GERMAN Spezifikationen Unterstützt Execute Disable Bit / Enhanced Intel Socket 1155 CPU Intel Core i7 / i5 / i3 / Pentium / Celeron Prozessoren Chipsatz Memory 64 Technology / Virtualization Technology / Hyper Threading Intel H61 IT8728 Super E/A SpeedStep® / Intel Architecture-64 / Extended Umgebungskontrolle, Bietet die häufig verwendeten alten Super Hardware-Überwachung E/A-Funktionen.
TH6 1 I TX Spezifikationen "CMOS löschen"-Sockel x1 USB2.0-Anschluss x1 Jeder Anschluss unterstützt 2 Fronttafel-USB2.0-Anschlüsse USB3.0-Anschluss x1 Jeder Anschluss unterstützt 2 Fronttafel-USB3.0-Anschlüsse Verbraucher-IR Anschluss x1 Stromanschluss (24-polig) x1 Stromanschluss (4-polig) x1 PS/2-Tastatur x1 S/PDIF Heraus x1 HDMI-Anschluss x1 VGA-Anschluss x1 Rückseiten-E DVI-D-Anschluss x1 /A LAN-Anschluss x1 USB2.0-Anschluss x4 USB3.0-Anschluss x2 USB3.
Motherboard Manual FRENCH SPEC Prend en charge les technologies d'exécution de bit Socket 1155 UC Processeurs Intel Core i7 / i5 / i3 / Pentium / Celeron Chipset de désactivation / Intel SpeedStep® optimisée/ d'architecture Intel 64 / de mémoire étendue 64 / de virtualisation / Hyper Threading Intel H61 IT8728 Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/S Moniteur de matériel patrimoniales la plus utilisée.
TH6 1 I TX SPEC Embase d'effacement CMOS x1 Connecteur USB2.0 x1 Connecteur USB3.0 x1 Chaque connecteur prend en charge 2 ports USB2.0 de panneau avant Chaque connecteur prend en charge 2 ports USB3.0 de panneau avant Connecteur de IR du consommateur x1 Connecteur d'alimentation x1 (24 broches) Connecteur d'alimentation x1 (4 broches) E/S du panneau arrière Clavier PS/2 x1 Sortie S/PDIF x1 Port HDMI x1 Port VGA x1 Port DVI-D x1 Port LAN x1 Port USB2.0 x4 Port USB3.0 x2 USB3.
Motherboard Manual ITALIAN SPECIFICA Supporto di Execute Disable Bit / Enhanced Socket 1155 CPU Processore Intel Core i7 / i5 / i3 / Pentium / Celeron Chipset Memoria principale Tecnologia Extended Memory 64 / Tecnologia Virtualization / Hyper Threading Intel H61 IT8728 Super I/O Intel SpeedStep® / Architettura Intel 64 / Funzioni di controllo dell’ambiente: Fornisce le funzionalità legacy Super I/O Monitoraggio hardware usate più comunemente.
TH6 1 I TX SPECIFICA Connettore USB2.0 x1 Connettore USB3.0 x1 Ciascun connettore supporta 2 porte USB2.0 pannello frontale Ciascun connettore supporta 2 porte USB3.0 pannello frontale Connettore IR del consumatore x1 Connettore alimentazione x1 (24 pin) Connettore alimentazione x1 (4 pin) I/O pannello Tastiera PS/2 x1 S/PDIF Fuori x1 Porta HDMI x1 Porta VGA x1 Porta DVI-D x1 posteriore Porta LAN x1 Porta USB2.0 x4 Porta USB3.0 x2 USB3.0 dispositivi (da Asmedia ASM1042) USB2.
Motherboard Manual SPANISH Especificación Admite Bit de deshabilitación de ejecución / Intel Socket 1155 CPU Procesador Intel Core i7 / i5 / i3 / Pentium / Celeron Conjunto de chips SpeedStep® Mejorado / Intel Architecture-64 / Tecnología Extended Memory 64 / Tecnología de virtualización / Hyper Threading Intel H61 IT8728 Iniciativas de control de entorno, Le ofrece las funcionalidades heredadas de Monitor hardware uso más común Súper E/S.
TH6 1 I TX Especificación Conector USB2.0 X1 Cada conector soporta 2 puertos USB2.0 frontales Conector USB3.0 X1 Cada conector soporta 2 puertos USB3.0 frontales Conector de IR del consumidor X1 Conector de alimentación X1 (24 patillas) Conector de alimentación X1 (4 patillas) Panel trasero de E/S Teclado PS/2 X1 Salida S/PDIF x1 Ratón HDMI X1 Puerto VGA X1 Puerto DVI-D X1 Puerto de red local X1 Puerto USB2.0 X4 Puerto USB3.0 X2 USB3.0 dispositivos (por Asmedia ASM1042) USB2.
Motherboard Manual PORTUGUESE ESPECIFICAÇÕES Suporta as tecnologias Execute Disable Bit / Socket 1155 CPU Processador Intel Core i7 / i5 / i3 / Pentium / Celeron Chipset o Super I/O / Extended Memory 64 / Virtualization / Hyper Threading Intel H61 IT8728 Especificaçã Enhanced Intel SpeedStep® / Intel Arquitecture -64 Iniciativas para controlo do ambiente Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O.
TH6 1 I TX ESPECIFICAÇÕES Conector para limpeza do CMOS x1 Conector USB2.0 x1 Conector USB3.0 x1 Conector de IR do consumidor x1 Conector de alimentação x1 Cada conector suporta 2 portas USB2.0 no painel frontal Cada conector suporta 2 portas USB3.0 no painel frontal (24 pinos) Conector de alimentação x1 (4 pinos) Teclado PS/2 x1 Saída S/PDIF x1 Porta HDMI x1 Entradas/S Porta VGA x1 aídas no Porta DVI-D x1 painel Porta LAN x1 traseiro Porta USB2.0 x4 Porta USB3.0 x2 USB3.
Motherboard Manual POLISH SPEC Obsługa Execute Disable Bit / Enhanced Intel Socket 1155 Procesor Procesor Intel Core i7 / i5 / i3 / Pentium / Celeron Chipset SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology / Hyper Threading Intel H61 Gniazda DDR3 DIMM x 2 Moduł pamięci DDR3 z trybem podwójnego kanału Pamięć Maks.
TH6 1 I TX SPEC Złącze główkowe kasowania CMOS x1 Złącze USB2.0 x1 Złącze USB3.0 x1 Złącze Konsument IR x1 Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinowe) x1 Klawiatura PS/2 x1 Wyjścia S/PDIF x1 Port HDMI x1 Port VGA x1 Back Panel Port DVI-D x1 I/O Port LAN x1 Port USB2.0 x4 Port USB3.0 x2 Każde złącze obsługuje 2 porty USB2.0 na panelu przednim Każde złącze obsługuje 2 porty USB3.0 na panelu przednim USB3.0 urządzeń (przez Asmedia ASM1042) USB2.0/USB1.
Motherboard Manual RUSSIAN СПЕЦ CPU (центральн ый Поддержка технологий Execute Disable Bit / Socket 1155 Процессор Intel Core i7 / i5 / i3 / Pentium / Celeron / Extended Memory 64 Technology / технологии виртуализация / Hyper Threading процессор) Набор Enhanced Intel SpeedStep® / Intel Architecture-64 Intel H61 микросхем Слоты DDR3 DIMM x 2 Модуль памяти с двухканальным режимом DDR3 Основная Максимальная ёмкость памяти 16 ГБ Поддержка DDR3 1066 / 1333 память Каждый модуль DIMM поддерживает Не
TH6 1 I TX СПЕЦ Контактирующее приспособление вентилятора системы x1 Источник питания для вентилятора системы Открытое контактирующее Задняя приспособление CMOS x1 USB2.0-разъём x1 USB3.0-разъём x1 Разъём едока ИКЫЙ x1 Разъем питания (24 вывод) x1 Разъем питания (4 вывод) x1 Клавиатура PS/2 x1 вывода для S/PDIF x1 Порт HDMI x1 Порт VGA x1 панель Порт DVI-D x1 средств Порт LAN x1 ввода-выв USB2.0-порт USB3.0-порт ода Каждый разъём поддерживает 2 USB2.
Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت Execute Disable Bit / Enhanced Intelﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت Socket 1155 وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ Intel Core i7 / i5 / i3 / Pentium /ﻣﻌﺎﻟﺠﺎت ﺑﺘﺮدد یﺼﻞ إﻟﻰ Celeron SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology / Hyper Threading ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ Intel H61 ﻓﺘﺤﺔ DDR3 DIMM ﻋﺪد2 ﻣﺰدوﺝﺔ اﻟﻘﻨﺎةDDR3وﺣﺪة ذاآﺮة ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى 16ﺝﻴﺠﺎ ﺑﺎیﺖ اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ ﺳﻌﺎت 1333 / 1066ﻣﻴﺠﺎ ﺑﺎ
TH6 1 I TX اﻟﻤﻮاﺻﻔﺎت ﻣﻨﻔﺬ اﻷﺣﻤﺮ ﺗﺤ ﺖ ﻣﺴ ﺘﻬﻠﻜﺔ ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺑﻮس( ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )4دﺑﺎﺑﻴﺲ( ﻋﺪد 1 ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ PS/2 ﻋﺪد 1 ﻣﻨﻔﺬ ﺥﺮج S/PDIF ﻋﺪد 1 ﻣﻨﺎﻓﺬ HDMI ﻋﺪد 1 ﻣﻨﺎﻓﺬ VGA ﻋﺪد 1 ﻋﺪد 1 ﻣﻨﺎﻓﺬ دﺥﻞ/ﺥﺮج ﻣﻨﺎﻓﺬ DVI-D ﻋﺪد 1 اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ ﻣﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ ﻣﻨﺎﻓﺬ USB2.0 ﻋﺪد 4 ﻣﻨﺎﻓﺬ USB3.0 ﻋﺪد 2 ﻣﻘﺒﺲ ﺹﻮت ﻋﺪد 5 USB3.0اﻷﺝﻬﺰة ) ﻗﺒ ﻞ ﻣﻦ (Asmedia ASM1042 USB2.0/USB1.
Motherboard Manual JAPANESE 仕様 Execute Disable Bit / Enhanced Intel SpeedStep® / Socket 1155 CPU Intel Core i7 / i5 / i3 / Pentium / Celeron プロ セッサ Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology / Hyper Threadingをサポートします チップセット Intel H61 DDR3 DIMMスロット x 2 デュアル チャンネルモードDDR3メモリモジュール 最大メモリ容量16GB メインメモリ DDR3 1066 / 1333 をサポート 各DIMMは 512MB/1GB/2GB/4GB/8GB DDR3 登録済みDIMMとECC DIMMはサポートされません をサポート Super I/O SATA 2 IT8728 環境コントロールイニシアチブ、 もっとも一般に使用されるレガシーSuper I/O機 H/Wモニタ
TH6 1 I TX 仕様 USB2.0コネクタ x1 各コネクタは2つのフロントパネルUSB2.0ポートをサポ ートします USB3.0コネクタ x1 各コネクタは2つのフロントパネルUSB3.0ポートをサポ ートします 消費者IRコネクタ x1 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 S/PDIFアウト x1 HDMIポート x1 VGAポート x1 背面パネル DVI-Dポート x1 I/O LANポート x1 USB2.0ポート x4 USB3.0ポート x2 USB3.0デバイス (で Asmedia ASM1042) USB2.0/USB1.