User's Manual

ManualsBrandsBircher Reglomat ManualsElectronicsMicrowave Motion Detector

User s guide

* The device must only be operated at a protective low voltage with safe electrical insulation. Product repairs must be performed solely by the manufacturer.

* Shut off all power going to the sensor before attempting any wiring procedures.

* Maintain a clean & safe environment when working in public areas.

* Constantly be aware of pedestrian traffic around the door area.

* Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.

* Always check placement of all wiring and components before powering up to ensure that moving door parts will not catch any wires and cause damage to equipment.

* Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.

Safety instructions

Microwave motion detector for automatic pedestrian doors with direction recognition Questions? Call us at 800 - 252-1272, 8am - 5pm central standard time.

Installation

= flash = press = on = time = Attention

Mounting on

a door header

or wall

Mounting on a

ceiling

Symbols meaning

ensing the future

DO NOT LEAVE ANY PROBLEMS UNRESOLVED - NEVER SACRIFICE SAFETY FOR ANY REASON

Physical installation

open sensor with screwdriver

drill holes using template

open sensor with screwdriver

Summary of content (7 pages)

PAGE 1
, User s guide sensing the future Microwave motion detector for automatic pedestrian doors with direction recognition Questions? Call us at 800 - 252-1272, 8am - 5pm central standard time. Safety instructions * The device must only be operated at a protective low voltage with safe electrical insulation. Product repairs must be performed solely by the manufacturer. * Shut off all power going to the sensor before attempting any wiring procedures.
PAGE 2
Connections RJ12 Plug-in screw terminal white white white 1 black black black brown brown 2 red green 3 4 blue yellow * blue 5 blue normaly open normaly closed B Manual Set-up [w/o RC Duo remote control] use Pin 4 use Pin 5 * Connect based on your application Set-up must be completed in 25 sec., or you will have to restart the set-up procedure from the beginning. sensitivity level check convenience function check Stufe / Step x 1... 9 1 xx11... 1::66 Steps Direction Mount.
PAGE 3
C Other field adjustments - frontal and lateral inclination changing frontal Inclination changing lateral Inclination 45 min. 5 Other field adjustments - normal and wide detection field Antenna clip stored on the back of the antenna module Normal detection field w/o clip Antenna clip placed on the front of the antenna module Wide detection field with clip 7.22' 2.2 m The use of the clip requires the amplification (F41) 2.2 m 7.22' (7.22') 2.2 m min. 1.64' (0.5 m) max. 8.20' (2.5 m) min. 3.
PAGE 4
E Settings with RC Duo [Bi-directional remote control] The RC Duo is bi-directional. Flashing keys on the RC Duo indicate that the settings have not been saved yet. Static lit keys on the RC Duo indicate that the settings have been saved. We recommend first programming the sensor with a convenience configuration and then fine tune settings if needed.
PAGE 5
C C 4 C 5 Hight mounting height setting Retail Vestibule B = with direction recognition D = medium F1 = short F2 = active F3 = off F4 = standard F5 = low F6 = off B = with direction recognition D = high F1 = medium F2 = active F3 = medium F4 = high F5 = off F6 = off > 3> m 9.84’ (3 m) (9.
PAGE 6
NO / NC Amplification level 1 for high mouting or wide field [max. mounting height 13 feet] 2 = active 1 F 4 1 >3 m (9.84') 9.84’ (3 m) on F 4 2 off < m (9.84') < 39.84’ (3 m) Relay switches on upon detection 2 3m <<9.84’ > >9.84’ 3m (3 m) (9.84') = passive 2 (3 m) (9.
PAGE 7
FCC APPROVAL This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: *this device may not cause harmful interference, and *this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.