User's Manual

4 times
Secondary Features
19
Secondary Features
18
4. Option 1 / Option 2 Input
·Additional sensors can be added to the system using Option 1 and/or Option 2 input(s).
·No additional programming is required.
·When the sensor(s) is(are) triggered, the parking lights will flash and the siren will sound.
5. Aux 1 Output
·Aux 1 Output can be used to control other devices. For example, window modules can be added to
roll up or roll down windows.
· + (0.5 sec) will activate Aux 1 Output. 2 parking light flashes and 2 siren chirps will confirm
output. The remote control will blink 2 times and beep 2 times.
6. Aux 2 Output
2. Program Remote Control to System
① Close driver’s side door. Insert key and turn to the ON position.
t h
② Turn the key ACC↔ON 4 times within 3 seconds. On the 4 time, leave the key in the
ON position.
③ 3 parking light flashes and 3 siren chirps will confirm remote control programming mode.
④ Press the correct button combination for 0.5 seconds as outlined below.
▶ Typical vehicles
+
▶ Vehicles that unlock doors after remote start
+
⑤ After each remote control is added, there will be a confirmation of 2 parking light flashes and 2 siren
chirps. You can add up to 3 remote controls per system.
⑥ Once the key is turned to the OFF position or 10 seconds without adding a remote control passes, the
system will exit remote control programming mode.
※ Each time a remote control is added, all remote controls must be reprogrammed to the system.
Adding a remote control erases previously stored remote controls from the system.
Feature
Default
Option
1. User Programmable Options
+ 2 sec
·When you enter programming mode by holding + for 2 seconds, the + LED’s will blink
1 time and 1 beep will be heard. Follow the chart below for programming the options.
※ The Button Combination includes the initial buttons to get into User Programmable Options.
3. Remote Start Reservation
① Before turning off the engine, put the transmission into Neutral. Ensure that the hand brake or
parking brake engaged. Take your foot off the foot brake.
② Turn the key to the OFF position. The engine should still be running.
③ Exit the vehicle within 2 minutes.
④ Once the last door is closed, the engine will turn off. Lock (Arm) the system. Remote start is ready
to be used.
※ Remote Start Reservation can be changed through the User Programmable Options on page 18.
1) Automatic Remote Start Reservation (Default)
① Before turning off the engine, put the transmission into Neutral. Ensure that the hand brake or
parking brake is engaged. Take your foot off the foot brake.
② Press the button for 2 seconds.
③ Turn the key to the OFF position. The engine should still be running.
④ Exit the vehicle within 2 minutes.
⑤ Once the last door is closed, the engine will turn off. Lock (Arm) the system. Remote start is ready
to be used.
2) 수동예약 (사용자 옵션설정)
·Manual transmission vehicles require remote start reservation in order to ensure that the vehicle is
properly prepared for remote start. There are 2 remote start reservation modes: automatic and manual.
Please note that automatic and manual do not refer to the transmission type. Rather, automatic and
manual refer to the type of remote start reservation.
+ 2 sec
Remote Start Run Time
Diesel Warm Up Time
Siren Sound Time
Turbo Timer Time
Remote Start Reservation
Cold Start Timer Time
15 min
10 sec
70 sec
5 min
Manual
2 hours
25 min
5 sec
100 sec
10 min
3 hours
→
→
→
→
→
→
→
→
→
→
→
→
Option
Option
Option
Option
Option
Option
+
+
+
+
+
+
(2 sec)
(2 sec)
(2 sec)
(2 sec)
(2 sec)
(2 sec)
→
→
→
→
→
→
5 min
15 sec
30 sec
2 min
Automatic
1 hour
Feature
Button Combination
Options
→ Default Values.
※ Each button must be pressed within 5 seconds of each other or else User Programmable
mode will terminate.
·Aux 2 Output can be used to control other devices. For example, window modules can be added to
roll up or roll down windows.
· + (0.5 sec) will activate Aux 2 Output. 2 parking light flashes and 2 siren chirps will confirm
output. The remote control will blink 2 times and beep 2 times.