PROHEAT® ESSENTIAL 1887, 1956 SERIES
IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER. When using an electrical appliance, basic precautions should be observed, including the following: WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY: » Connect to a properly grounded outlet only. See grounding instructions. Do not modify the 3-prong grounded plug. » Do not leave appliance when it is plugged in. Unplug from outlet when not in use and before servicing. » Use indoors only.
Thanks for buying a BISSELL deep cleaner We’re glad you purchased a BISSELL deep cleaner. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL deep cleaner is well made, and we back it with a limited two-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Care department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
Product View 1. 1 2 Ergonomically Designed Handle 2. Spray Trigger 3. Cord Wrap 4. Power Cord 14 5. Integrated Carry Handle 4 6. Tank Carry Handle 7. Ready Tools™ Dial 8. Removable Nozzle 9. Dirtlifter® PowerBrush 15 10. Edge Sweep® Brushes 3 11. Belt Access Door (underside of machine) 12. Recline Pedal 13. Power Switch (red pedal) 5 14. 3” Tough Stain Tool 15. Spraying Crevice Tool 6 7 12 13 8 11 9 10 Built-in Tool Holder Some models come with a tool holder feature as pictured here.
Assembly WARNING Do not plug in your deep cleaner until you are familiar with all instructions and operating procedures. The only tool you will need to assemble your cleaner is a Phillips head screwdriver. 1. Slide handle assembly onto lower body and secure with two long screws. 1 2. Attach upper hose rack to back of handle assembly by guiding the hook up into slot location and pressing firmly upward until it is seated flush with the back of the machine.
Cleaning Formula WARNING To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the deep cleaner. Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and may void the warranty. Keep plenty of genuine BISSELL 2X* formula on hand so you can clean and protect whenever it fits your schedule.
Operations Machine prep 1. Remove the tank from the base of the machine by lifting the tank carry handle. 2. Carry like a bucket to the sink. Pull upward on bottom edge of the latch in the back of the tank to unhook and remove the lid. 1 2 3 5 3. Pull up on the bladder fill cover that says “Fill Here”. Fill the bladder with clean hot tap water (140°F/60°C MAX). *Do not boil or microwave water as it can destroy the bladder. 4.
Operations Empty the 2-in-1 water tank/clean removable nozzle 1. Turn power switch off. Remove the 2-in-1 water tank from the base using the tank carry handle. Carry the tank like a bucket to a utility sink where you will dispose of the collection water. Pull upward on bottom edge of the latch in the back of the tank to unhook and remove the lid. 1 2 2. Empty collection water from bottom of tank. 3.
Operations Ready Tools™ (continued) 6. To begin cleaning with attachments, follow the instructions on page 7 for filling the 2-in-1 water tank. 7. Set the ReadyTools dial to the TOOLS setting. This will allow spray and suction from the hose. 7 8. Attach the cleaning tool of your choice to the end of the hose. If using a Deep Reach tool, follow section below. 9. Clean by pressing the trigger to spray solution onto the area to be cleaned. Slowly move the tool back and forth over the soiled surface.
Operations *Cleaning with Deep Reach™ Tool *This tool is NOT included with the machine but is available for purchase on BISSELL.com. Please read instructions for use if you’ve purchased this tool. 1 1. Set tool on soiled surfaces and press the trigger to spray solution onto the soiled area to be cleaned. 2. Slowly move the tool back and forth over the soiled surface, keeping the tool in contact with the carpet. 3 3. Release trigger and move tool slowly over the soiled area to suction up water and dirt.
Operations *Hard Floor Cleaning (continued) 5. Place tank in to machine base, seating firmly in base. Be sure the ReadyTools dial is set to FLOOR CLEANING. 6. Plug into an outlet and turn the power on. 7. Plan your cleaning route to leave an exit path. Be sure to allow adequate time for floors to dry. 8. While pressing the spray trigger, make one slow forward wet pass and another back. Caution: Do Not Overwet. 9.
Maintenance & Care Machine care For best results, a few simple steps can assure your machine is well maintained after cleaning is complete. 1. Turn power switch off. Unplug the machine and wrap the power cord. 2. After emptying the 2-in-1 water tank, rinse it with running hot tap water, taking care to clean underneath and around the heavy duty bladder. Clean out red lint screen prior to replacing tank. Removable nozzle may be rinsed if necessary. 3. Replace the 2-in-1 water tank on the machine. 4.
Maintenance & Care Belt Replacement Instructions 1. Turn off the machine and unplug it from the outlet. Wrap hose and cord on wraps. 2. Remove the 2-in-1 water tank and set aside. 3. IMPORTANT: Fully recline handle and turn unit upside down. WARNING To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks. 4. Locate red Belt Access Door and remove two screws.
Troubleshooting Problem Reduced spray OR no spray DirtLifter PowerBrush does not turn Cleaner not picking up solution Possible causes Remedies Bladder may be empty. Turn power switch off; refill bladder with clean hot tap water and formula. 2-in-1 tank may not be seated properly. Turn power switch off; remove tank and reseat tank. Pump may have lost prime. Turn power switch off; after 1 minute turn on and depress spray release trigger. The motor belt may be broken.
Warranty Service Limited Two-Year Warranty Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area. If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
Register your product today! Registering is quick, easy and offers you benefits over the lifetime of your product. You’ll receive: BISSELL Rewards Points Product Support Reminders and Alerts Automatically earn points for discounts and free shipping on future purchases. Faster Service We’ll contact you with any important product maintenance reminders and alerts. Supplying your information now saves you time should you need to contact us with questions regarding your product.
