® USER’S GUIDE 58F8/18M9P SERIES 3 Safety Instructions 4 Product View 5 Assembly 6-8 Operation 8-12 Maintenance and Care 13-14 Troubleshooting 14 Consumer Services 15 Replacement Parts 15 Accessories 16 Warranty
Thanks for buying a BISSELL Rewind SmartClean /Rewind PowerClean® ™ We’re glad you purchased a BISSELL vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. By purchasing this product you are helping BISSELL with our commitment to reducing our impact on the environment through an expanding range of sustainable design efforts. Your carpet cleaner is well made, and we back it with a limited three year warranty.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: Read all instructions before using your upright VACUUM. Always connect to a polarized outlet (left slot is wider than right). Unplug from outlet when not in use and before conducting maintenance. WARNING: To reduce the risk of fire, electric shock, or injury: ■ Do not modify the polarized plug to fit a non-polarized outlet or extension cord.
Product view Handle Stretch Hose Hose Clip TurboBrush® Clean Carpet Sensor (select models only) Clean Filter Indicator (select models only) Carry Handle Crevice Tool Extension Wand Quick Reach® Handle Combination Dusting Brush/ Upholstery Tool Dirt Container Hepa Media Filter Filter Cup Cord Rewind Lock ’n Seal™ Lever Automatic Cord Rewind Headlight Height Adjustment Knob Hose Wand Handle Release Pedal Hose Wand Base Foot Hose Furniture Protection Guard Powerfoot c aution: Do not plug in
Assembly The only tool you’ll need to assemble your vacuum cleaner is a Philips head screwdriver. 2. Attach handle to vacuum 1. Locate the vacuum handle and remove the screw packet taped to the base of the handle. 2. Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body. 3. Check to be sure the handle is fitted to the vacuum body. If there is a gap in front, continue to push firmly until the handle is flush. 4.
Operation Handle position Press the handle release pedal with your foot to place your BISSELL vacuum into one of three cleaning positions. 1. Upright 2. 3. For storage and above floor cleaning with tools. Normal cleaning Press handle release pedal once. Use for most household floor cleaning tasks. Low cleaning With the vacuum in normal cleaning position, press handle release pedal again, use for reaching under low furniture such as tables, chairs or beds.
Operation Clean filter indicator (select models only) The Clean Filter Indicator tells you when airflow in the vacuum is reduced due to dirty filters or a clog in the hose. The Clean Filter Indicator will remain green until the airflow is reduced. At that time, it begins to change to red. When it is fully red, the airflow is significantly reduced or blocked. Follow the steps on page 9 to clean your filters. All filters in the vacuum should be cleaned or replaced when the Clean Filter Indicator turns red.
Operation Power cord The power cord is located on the right of the vacuum. Gently pull out the power cord, watching for the yellow line. Stop pulling the power cord once the yellow line is visible. There is also a red line, which indicates the end of the usable cord. Do not pull the power cord out beyond the red line. Automatic cord rewind Your vacuum is equipped with an automatic cord rewind. When cleaning is finished, press the power button OFF and grasp the plug to disconnect from the electrical outlet.
Maintenance and care Empty Dirt Container continue 3. Grasp dirt cup portion handle and pull straight out to remove from vacuum. 4. Empty dirt into garbage container. 5. Put the dirt container back in the vacuum and slide the lever to the "Lock" position. 3. Note: The dirt container may be washed in warm water with a mild detergent. Make sure it is completely dry before replacing. DO NOT PUT IN DISHWASHER.
Maintenance and care WARNING: Do not operate cleaner Cleaning the pre-motor filter 1. Unplug the cleaner from electrical outlet. 2. The pre-motor filter protects the motor from debris. It is located underneath the filter cup in the center of the round part of the Lock ‘n Seal lever. 3. Remove the small round filter and any debris on top of it. Rinse well under warm water, then air dry thoroughly before replacing. with damp or wet filters or without all filters in place.
Maintenance and care Checking rotating floor brush and drive belt continued 6. Clean strings, hair and other debris from motor pulley and drive belt areas. 7. Check drive belt carefully for wear, cuts or stressed areas. 8. Check air passageway for obstructions. Remove debris from this area. 8. Replace drive belt Use only genuine BISSELL style 9 replacement belts (#32074) in your BISSELL vacuum. 1. Turn power off. Unplug cleaner from electrical outlet. 2.
Maintenance and care Cleaning a clog 3. Low suction or poor pickup may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action, check for clogs. 1. Unplug cleaner from electrical outlet. 2. Empty dirt container. 3. Check upper tank for build up or clogs. 4. Check the suction inlet for a clog. 5. Grasp the quick reach handle and lift hose wand to separate from the suction opening.
Troubleshooting Vacuum cleaner won’t turn on Possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Blown fuse/tripped breaker 2. Check/replace fuse or reset breaker 3. Damaged cord 3. Refer to a BISSELL authorize service center for repair or replacement Vacuum cleaner won’t pick up dirt Possible causes Remedies 1. 1. Adjust powerfoot to correct height setting Incorrect height adjustment 2. Hose not attached to suction opening 2.
Troubleshooting Visible dirt escaping from cleaner Possible causes Remedies 1. 1. Empty dirt container Dirt container full 2. Filters missing or installed incorrectly 2. Check pre-motor and post-motor filters for correct installation Cord will not retract Possible causes Remedies 1. 1. Follow instructions on page 8 Knotted or twisted Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSELL product.
Replacement parts You may purchase replacement parts from your retailer, by calling BISSELL Consumer Services or by visiting our website. To locate a retailer near you, or to place an order using Visa, MasterCard, Discover or American Express, call BISSELL Consumer Services 1-800-237-7691 Monday - Friday Saturday 8 a.m. — 10 p.m. ET 9 a.m. — 8 p.m. ET Or visit our Website - www.bissell.com Item Part No.
Warranty - BISSELL Rewind SmartClean & Rewind PowerClean This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.