S RT ES REVOLUTION® PET PRO .A T. 18 7 6 U.S . HO M NING E LEA XP E EC UPRIGHT CARPET CLEANER MODEL 20666 Important Safety Instructions................................ 2 What’s in the Box? .........................................................3 Assembly ..............................................................................3 1 Filling the Clean Water Tank....................................4 Cleaning Carpets and Area Rugs ........................5 2 Cleaning with Hose and Tools..........
SYMBOL EXPLANATION SYMBOL EXPLANATION SYMBOL EXPLANATION Caution. Use only BISSELL® cleaning formulas intended for use with this machine. Lock. Read operator’s manual. Disconnect power before servicing. Do not freeze. Risk of fire. Protection against moving parts. Risk of electric shock. Risk of automatic start-up. Do not expose to rain. Use warm water, temperature up to 60°C. Store indoors. Check the manufacturer’s tag before cleaning textile.
SAVE THESE INSTRUCTIONS ORIGINAL INSTRUCTIONS. FOR OPERATION ON A 220-240 VOLT A.C. 50-60 HZ POWER SUPPLY ONLY. THIS MODEL IS FOR HOUSEHOLD USE ONLY. IMPORTANT INFORMATION • Keep appliance on a level surface. • If your appliance has a motorised Brush Roll, do not leave machine running in the same spot without the handle fully upright. • To reduce the risk of a leaking condition, do not store unit where freezing may occur. Damage to internal components may result.
Filling the Clean Water Tank Find more formulas at BISSELLdirect.co.uk. This machine is compatible with BISSELL® formulas made for upright carpet cleaners. Always use genuine BISSELL formulas in your machine. Other formulas may harm the machine. 1. Lift the clean water tank up to remove from the machine. Unscrew the cap. 2. Choose your formula.* Fill tank with warm tap water (140°F/60°C MAX) to WATER line. Do not use boiling water. Do not heat water or tank in microwave. Add formula to FORMULA line. 3.
Cleaning Carpets and Area Rugs • Remove any solids and use a dry vacuum cleaner before using your deep cleaner. • To prevent damage to Berber carpets, avoid repeated strokes in the same area. Before cleaning area rugs, check the manufacturer’s tag and test an inconspicuous spot for colourfastness. Don’t use on silk or delicate rugs. • Stay off carpet until dry. 1. Plug into a properly grounded outlet. Select cleaning mode using the chart below. Press the power button to turn the machine ON. 2.
Cleaning with Hose and Tools Tools vary by model. Visit BISSELLdirect.co.uk for additional tools. 1. Lift accessory hose door toward the machine to open. 2. Insert hose and snap into place with coloured release clip facing away from machine. 3. Attach tool to the end of hose. Deep Stain Tool; 3”, 4” and 6” Tools; and Spraying Crevice Tool 1. Point tool about 1 inch above spot or stain and press trigger. 2. Release spray trigger and gently scrub the stain.
Cleaning with Hose and Tools (continued) Stain Trapper Tool 1. Point tool about 1 inch above the spot or stain and press trigger. Suction stain by placing tool on surface and slowly moving backwards. 2. To empty the tool tank, rotate clockwise. Pour dirty liquid into sink or toilet and rinse. Allow time to air dry. 3. Return the tank to the tool by lining up the grooves and twisting it into place. 2-in-1 Upholstery Tool Wet Suction Channel Dry Suction Channel Switch between dry and wet settings.
Emptying the Dirty Water Tank Important: The float stack prevents your dirty tank from overflowing. 1. Press tank handle and tilt tank toward you. Grab handle and tank with both hands and pull up and away to remove. 2. Empty the tank. Quick empty: Pull the rubber tab and tilt to pour. When closing, ensure tab is sealed tight. Final clean and rinse: Unscrew ring at bottom of tank. Remove and rinse float stack. Reinstall float stack by aligning arrows and lock into place.
Replacing the Belts and Brush Rolls 1. Unplug machine and remove both tanks. Remove nozzle and brush roll cover (see steps in “After-Cleaning Care”). Press the recline pedal and lay machine on its back. 2. Use a flathead screwdriver to press into the slot at the back and then front of the belt access door. Lift to remove. Use a Phillips-head screwdriver to remove the screw under the wheel, slide down to remove. 3. Lay machine on its back.
Troubleshooting Below are some of the issues you may run into. If you don’t see the issue you’re experiencing below, visit BISSELLdirect.co.uk. Problem Possible Cause Reduced or no Clean water tank empty. spray through Clean water tank not seated foot of machine completely. CleanShot continues spray when machine is OFF Loss of suction No power Leaking tank Refill tank. Turn power OFF. Remove and reseat tank. Hose is not primed or has lost prime. 1. Turn power OFF and unplug. Remove nozzle.
Limited Warranty This limited warranty only applies outside of the USA, Canada, Australia, New Zealand, and mainland China. It is provided by BISSELL International Trading Company B.V. (“BISSELL”) and gives you specific rights. It is offered as an additional benefit to your other rights under your local laws, which may vary from country to country. You can find out about your legal rights and remedies by contacting your local consumer advice service.
We’re Waggin’ Our Tails! BISSELL proudly supports BISSELL Pet Foundation® and its mission to help save homeless pets. When you buy a BISSELL® product, you help save pets, too. We’re proud to design products that help make pet messes, odors and pet homelessness disappear. Visit BISSELLsavespets.com to learn more. But wait, there’s more! Join us online for a complete guide to your new product, including troubleshooting, product registration, parts, and more. Go to BISSELLdirect.co.uk.
