CleanView II ® B A G L E S S USER’S GUIDE 3574/73G8/3576/20Q9 SERIES 3 Safety Instructions 4 Product View 5-6 Assembly Instructions 6-8 Operation / Special Tools 8-12 Maintenance 12-13 Troubleshooting 14 15 16 Warranty Replacement Parts Consumer Services
® Thanks For Buying A BISSELL CleanView II We’re glad you purchased a BISSELL CleanView II Vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home vacuuming system. Your BISSELL CleanView II is well made, and we back it with a limited comprehensive one-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services Department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
Important Safety Instructions When using an electrical appliance, basic precautions should be observed, including the following: Read all instructions before using your upright VACUUM. Always connect to a polarized outlet (left slot is wider than right). Unplug from outlet when not in use and before conducting maintenance. WARNING: To reduce the risk of fire, electric shock, or injury: unplugging vacuum cleaner. ■ U se extra care when cleaning stairs. ■ Unplug before attaching the turbobrush.
Cord Clip Hose Clip Handle Stretch Hose Carrying Handle Quick Release Cord Wrap Power Cord Stair Cleaning Handle Power Switch Crevice Tool Quick Reach® Handle Extension Wand Louvers Combination Dusting Brush/ Upholstery Tool Hose Wand Upper Tank Hose Wand Base Dirt Container Filter Cup Inner and Outer Circular Filters Foot Hose Headlight Post-Motor Filter Optional Hepa Media Filter (Select Models Only) Lock ’n Seal™ Lever Handle Release Pedal Height Adjustment Knob Furniture Protection Guard Po
How To Put It Together The only tool you’ll need to assemble your vacuum cleaner is a screwdriver. Attach Handle To Vacuum 1. Locate the vacuum Handle and remove the screw packet taped to the base of the Handle. 2. Stand the vacuum upright and slide the base of the Handle firmly into the grooves at the top of the vacuum body. 3. Check to be sure the Handle is fitted to the vacuum body. If there is a gap in front, continue to push firmly until the Handle is flush. 4.
How To Use Your Vacuum Handle Positions Press the Handle Release Pedal with your foot to place your vacuum in one of three cleaning positions. 1. Upright- For storage and above floor cleaning with tools. 2. Normal Cleaning- Press Handle Release Pedal once. Use for most household floor cleaning tasks. 3. Low Cleaning- With the vacuum in normal cleaning posi- tion, press Handle Release Pedal again. Use for reaching under low furniture such as tables, chairs or beds.
Special On-Board Tools Your BISSELL CleanView II is not only a powerful carpet and rug vacuum cleaner, it’s also a versatile above floor vacuum cleaner when you select one of the special tools. 1. Raise Handle to Upright Position. NOTICE: The Floor Brush will continue to rotate while you use your vacuum for above floor cleaning. To prevent carpet damage, do not lean on the vacuum or let the Powerfoot tilt forward. 2.
How To Maintain Your Vacuum W ARNING: To reduce the risk of To maintain maximum cleaning performance, the following maintenance steps must be performed: electric shock, turn Power Switch OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks. 1. Empty the Dirt Container when the dirt reaches the “Full” line on the side. 2. Check the Inner and Outer Circular Filters and the Pre-Motor Filter at least once a month and clean or replace as needed.
Cleaning The Inner & Outer Circular Filters 4. Separate the Outer foam and Inner pleated Circular Filters. Wash each individually by hand in warm water. Mild detergent may be used if desired. Rinse well, then air dry thoroughly before putting them back together and replacing in Filter Cup. 5. The Filter Cup may be washed in warm water with a mild detergent. Make sure it is completely dry before reassembling with filters. 6. The Upper Tank and Louvers may also be wiped clean with a damp cloth.
Check Rotating Floor Brush and Drive Belt Continued 3. For standard models, remove the four screws as shown with a Phillips Head Screwdriver. Lift the Brush Cover off. For wide cleaning path models, Lift tab 1 and release the three latches in order 2-4 as marked. Lift the Brush Cover off. 4. Grasp Rotating Floor Brush at both ends and lift. 5. Clean strings, hair and other debris from Rotating Floor Brush, paying particular attention to brush ends. 6.
Replace Lightbulb Continued 3. Determine the light bulb type of your vacuum: Standard Bulb (#203-1297) – approximately 1” long, flat end Large Bulb (#203-1007) – approximately 2” long, round end 4. Standard Bulb – remove the bulb from the socket by grasping bulb and pulling straight out. Install the new bulb by pushing it gently into the socket until the bulb snaps into place. Large Bulb - remove the bulb from the socket by pushing bulb in gently and turning it towards brush.
Clearing Clogs Continued 3. Check Upper Tank and Louvers for build up or clogs. Louvers Check to make sure Louvers are installed correctly. To unlock the Louvers, grasp the rim and turn toward the left. Pull straight down to remove. If the Louvers are missing or not locked into place, check and clear the tube in the center of the Dirt Container. Suction Inlet 4. Remove the Twist ‘n Snap Hose from the vacuum by turning to the left. Check the Suction Inlet, Hose and Hose Wand for clogs.
Troubleshooting Continued Vacuum cleaner won’t pick up dirt continued Possible Causes Remedies Dirt Container not installed properly 10 Filters are dirty 11 12 Louvers missing or installed incorrectly 12 10 11 Position correctly and lock in place Check and clean Inner and Outer Circular Filters, Pre-Motor and Post-Motor Filters Check for a clog in the tube in the center of the Dirt Container, clear and properly install Louvers Tools won't pick up dirt Possible Cause Remedies Crack
Replacement Parts – BISSELL Cleanview II Series You may purchase replacement parts from your retailer, by calling BISSELL Consumer Services or by visiting our website. To locate a retailer near you, or to place an order using Visa, MasterCard, Discover or American Express, call BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 a.m. — 10 p.m. ET Saturday 9 a.m. — 8 p.m. ET Or visit our Website - www.bissell.com Item Part No.
BISSELL Consumer Services For information about repairs or replacement parts, or questions about your warranty, call: BISSELL Consumer Services 1-800-237-7691 Monday - Friday Saturday 8 a.m. — 10 p.m. ET 9 a.m. — 8 p.m. ET Or write: BISSELL Homecare Inc. PO Box 3606 Grand Rapids, MI 49501 ATTN: Consumer Services Or visit the BISSELL website - www.bissell.com When contacting BISSELL, have model number of unit available.
Warranty This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below. Limited One Year Warranty Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare Inc.