User Manual
STATUS INDICATOR REFERENCE
FIG.A
AMP SERIES USER GUIDE
PLAY MUSIC
Press
“Power” twice
STOP/PAUSE MUSIC
Press
“Power“ once
BACKTRACK
Press
“Down“ twice
FAST FORWARD
Press
“Up“ twice
FOR A DIGITAL COPY OF THIS USER GUIDE LAUNCH CLEARLINK APP OR
VISIT WWW.UCLEAR-DIGITAL.COM
Press & Hold “Power”
for 5 seconds
POWER OFF
Press & Hold “Power”
for 2 seconds
POWER ON
Press & Release “Up”
once per level
VOLUME UP VOLUME DOWN
Press & Release “Down”
once per level
Press all 3 buttons
for 2 seconds
RESET
Power on the unit.
Hold “Up” and
“Down”2 seconds
until LED alternately
blinks blue and red.
Turn on the phone’s
Bluetooth, search
Bluetooth device list
and select/connect
your AMP model.
PHONE FUNCTIONS
ANSWER INCOMING CALL
Say “Hello”or
Press “Power” once
REJECT OR END CALL
Hold “Power”
2 Seconds
PAIRING TO SMARTPHONE
REDIAL LAST NUMBER
Hold “Power” and
“Up” 2 seconds
VOICE DIAL
Hold “Power” and
“Down” 2 seconds
x2
MUSIC PLAYBACK
x2
x2
BUTTONS
UNIT 1 UNIT 2 UNIT 3 UNIT 4 PLUS
GROUP INTERCOM
STOP INTERCOM
Hold “Down” 2 seconds
START INTERCOM
Hold “Up” 2 seconds
Power off all the units.
On the 1st unit, hold “Power“ and “Down“ 5 seconds, LED will blink
purple.
On the 2nd unit, hold “Power“ and “Up“ button 5 seconds, LED will
blink purple, wait until the previous unit blinks blue, then proceed to
next step.
Repeat step 3 if you have more units. Go to step 5 if no more units.
To end the pairing
process, press “Power”
on the last unit in the
chain.
Power Off all Units to
store pairing into
memory.
1)
2)
3)
4)
5)
6)
5.5”
MIC MINIMUM PLACEMENT
SEE FIG.A
SPEAKER
MIC PORT
FACE FORWARD
TOWARDS EAR
CROSS-BRAND INTERCOM PAIRING
Set your [Other brand] intercom device in
pairing mode.
Power on the AMP unit by pressing the
power button 10 seconds until LED blinks
purple. Pairing is successful when AMP
LED blinks blue.
Power Off AMP unit to store pairing into
memory.
GROUP & CROSSBRAND INTERCOM USE
PULSE PRO & BOOST PRO PLACEMENT
OR
BOOST PLUS PLACEMENT
SPEAKER
MICROPHONE
FACE FORWARD
TOWARDS EAR
SPEAKER USB PLUG
Insert the speaker USB
wire into the control
unit until you can no
longer see the 3 ribs on
the USB speaker wire plug.
MOUNTING (PERMANENT MOUNT)
TOP
MOUNTING (TEMPORARY MOUNT)
1) Position and fasten the clip
bracket onto the helmet.
2) Remove the metal handles
after clip bracket has been
installed.
3) Use additional
anti-slip rubber
patch provided
if required.
1) Locate and clean a position on the
left side of helmet close to lower
edge of the helmet.
2) Peel off the 3M double sided tape
protective film and place the mount
with logo on bottom and place Mount
to the position in step 1.
3) Apply pressure to the metal bracket
to ensure that the bracket is firmly
secured. Note: It takes 24hours for
adhesive to set.
INSTALL CONTROL UNIT
1) From the top, slide AMP unit onto the
bracket. You should hear a ‘click’ sound
when fully inserted.
2) Fully insert the speaker USB connector.
REMOVE CONTROL UNIT
Remove USB speaker connector.
Slide AMP upward to release from
1)
2)
UNIT 1
Quickly Press
“Power” & Down
twice
UNIT 2
Quickly Press
“Power” &“Up“
twice
x2
MUSIC SHARE (AMP PRO & AMP PLUS ONLY)
x2
Pair Units for Group Intercom(See Above)
On Unit 1 quickly press “Power” & Down” two
times.
On Unit 2 quickly press “Power” & Up” two
times.
Both Units will blink blue and red until paired.
On successful pairing units will blink Blue.
Unit 1 will now share it’s music to unit 2
x2
x2
1)
2)
3)
4)
3/16”
1)
2)
After successful Pairing power off Unit to
store Phone into Memory. When AMP Pro,
AMP Plus or Amp is powered on, it will auto
connect to the phone.
3)
Both mics should be placed parallel to each other
1)
2)
3)
Make sure all intercom units are powered on and Paired for
Group Intercom(see group intercom) and are in Intercom Mode.
On unit 1 and unit 2 press “Power” and “Up” until indicator
blinks purple.
After both units are blinking purple press “Power” on unit 2 to
end the pairing process.
Note: You will only need to pair this ONCE and you can create
multiple private groups in a Group Intercom.
ENABLE 2 PARTY PRIVATE INTERCOM WITHIN GROUP INTERCOM
1)
2)
3)
UNIT 1 & 2
Press
“Power” &“Up“
Indicator will
Blink Purple
UNIT 2
Press
“Power”
to end pairing
TO ENTER GROUP INTERCOM FROM PRIVATE INTERCOM
Press “Power” once. A single “Beep” will sound.
TO ENTER PRIVATE INTERCOM FROM GROUP INTERCOM
Press “Power” once. A double “Beep” will sound.
TECHNICAL DATA
Bluetooth: V4.2 (BR/EDR/BLE), Class 1
Profiles: HSP, HFP, A2DP
Intercom: AVRCP
Carrier Frequency: 2.402 - 2.480 GHz
Range: Up to 700m (0.43mi)
AMP Pro Multi-Hop Intercom: 2 Users and Up
AMP Plus Multi-Hop Intercom: 2-6 Users
AMP Multi-Hop Intercom: 2 Users
Battery: 3.7V, 500mAh Lithium-ion
Talk Time: Up to 10 Hours
Stand by Time: 400 Hours
Operating Temp: -30C(-4F) to 60C(140F)
Required Charging Temp: 0°C(32F) to 45°C(+113 F°)
Controller Unit Size: 60 x 40 x 18mm(2.9 x 1.75 x 1")
ClearLink: Android 4.4 or Later. Apple iOS 8 or Later
Off (No Power)
On (Bluetooth not connected)
On (Bluetooth connected)
Phone & Music Device Pairing Mode
Call in Progress
In-coming Call
Battery Low
Power Down
Intercom Connected
Intercom Pairing Mode (first unit)
Intercom Pairing Mode (subsequent unit)
Battery Charging
Battery Fully Charged
Battery Faulty
N/A
Blinks Blue Quickly
Blink Blue Slowly
Blinks Blue and Red Alternately
Blinks Blue Very Slowly
Blinks Blue and Red Alternately
Blinks Red Every 2 Seconds
Blinks Red 5 Times
Blinks Blue Twice Every 2 Seconds
Blinks Purple Fast
Blinks Purple Slowly
Solid Red
Solid Blue
Solid Purple
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
BUTTON CONFIGURATION REFERENCE
Power On
Power Off
Activate Bluetooth Pairing
Volume Up
Volume Down
Reset
Hold Press “Power” once for 2 seconds
Hold “Power” for 5 seconds
Hold “Up” and “Down” for 2 seconds
Press “Up” once per volume level
Press “Down” once per volume level
Press “Power”, “Up” and “Down” once simultaneously
Pick up Incoming Call
End Call In Progress
Reject Incoming Call
Voice Dial
Last Number Redial
Press “Power” Once
Hold “Power” for 2 Seconds
Hold “Power” for 2 Seconds
Hold “Power” and Down for 2 Seconds
Hold “Power” and Up for 2 Seconds
Play
Stop
Fast Forward Track
Backtrack
Press “Power” 2 Times
Press “Power” 1 Time
Press “Up” Button 2 Times
Press “Down” Button 2 Times
Pairing as Unit 1
Pairing as Unit 2
Connect intercom
Disconnect intercom
Unit is off, “Power” and “Down” for 3 seconds
Unit is off, “Power” and “Up” for 3 seconds
Hold “Up” for 2 Seconds
Hold “Down” for 2 Seconds
BASIC COMMANDS
PHONE CALLS
MUSIC
GROUP INTERCOM
Set Up
Switch To Group Intercom
Switch To Private Intercom
While all units are connected, hold “Power” and “Up”
Press “Power” 1 Time
Press “Power” 1 Time
PRIVATE INTERCOM
Activate Open Pairing
Activate [other brand] Pairing
Connect intercom
Disconnect intercom
Unit is off, hold “Power” for 10 seconds
Refer to the Respective Manufacturer User Manual
Hold “Up’ for 2 Seconds
Hold ”Down” for 2 Seconds
OPEN INTERCOM