User's Manual Mobile Printer http://www.samsungminiprinters.
Information to the user NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
■ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet. You must use only the supplied adapter. • • • • • It is dangerous to use other adapters. This can provoke over-heating and a fire. If the plug is wet or dirty, dry or wipe it before usage.
CAUTION Violating following instructions can cause slight wound or damage the appliance. If you observe a strange smoke, odor or noise from the printer, unplug it before taking following measures. Keep the desiccant out of children’s reach. • If not, they may eat it. • Switch off the printer and unplug the set from the mains. • After the disappearance of the smoke, call your dealer to repair it. TO UNPLUG PRINTER Install the printer on the stable surface.
All rights reserved. No part of this publication may reproduced, stored in a retrieval, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of BIXOLON. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this book, BIXOLON assumed no responsibility for errors or omissions.
■ Introduction The SPP-R200 is a high-quality Mobile printer. This mobile printer has the following features.
• Front view Rear cover Open button Power button Feed button Front cover (MSR) BT cap (Bluetooth download connector) • Rear view Belt strap fixing hole Battery pack Lower cover Serial/USB cable connector Power connector N OT ES Please be sure to read the instructions in this manual carefully before using your new printer. Rev. 1.
■ Table of Contents 1. Unpacking ······························································································ 9 2. Installation and Operation ·································································· 10 3. 2.1 Installing the Battery ························································································10 2.2 Charging the Battery ························································································10 2.
1. Unpacking Your printer box should include the items shown in the illustration below. If any items are damaged or missing, please contact your dealer. SPP-R200 Power cord CD Rev. 1.
2. Installation and operation 2.1 Installing the battery 1) Insert two hook of battery into two hole of printer. 2) Lock the battery into the printer until it makes a clicking sound. N OT ES The battery is packed uncharged. For the printer works, you must charge the battery using the battery charger or the battery cradle (option). (See “2.2 Charging the battery”.) 2.2 Charging the battery 1) Make sure the printer is turned off. 2) Connect the power cord to the battery charger.
2.4 Connecting the interface cable (Option) 1) Connect the interface cable to the printer’s interface connector. • Communication cable Pin No. Signal name Direction Function 1 GND - 2 TXD Output Transmit data 3 RXD Input Receive data Ground Request to send 4 nRTS Output Set high when printer is ready to accept a command or data 5 nCTS Input 6 GND - Ground 7 GND - Ground 8 D+ - Differential data line 9 D- - Differential data line 10 nINDEX Output Rev. 1.
2.5 Installing the paper roll 1) To prevent data loss, make sure that the printer is not receiving data. 2) Open the rear cover by pushing the open button. 3) Insert the paper roll as shown. (Remove the used paper roll core if there is one.) 4) Be sure to note the correct direction that the paper should come off the paper roll. 5) Pull out small amount of paper as shown. Then close the rear cover. 6) Tear off the extra paper by pulling it toward the front of the printer. Rev. 1.
2.6 Using the belt strap 1) Insert the screw of the belt strap in a hole of lower cover. 2) Fasten the screw of the belt strap by rotating a coin as shown. 3) Spread the velcro fasteners of the belt strap. 4) Insert the belt strap to the belt. 5) Attach to the Velcro fasteners as shown. Rev. 1.
2.7 Using the control panel Most of the functions of this printer are governed by software, but you can monitor the printer’s status by looking at the lights on the control panel and for some procedures you will use the buttons. • POWER button Use this button to turn on the power or to turn off the power. If you press this button when the printer is turn off, the printer is turn on. And if you press this button during 2 seconds when the printer is turn on, the printer is turn off.
disconnection. After all it means the printer is not ready to communicate with host. Rev. 1.
3. Setting the Memory Switches This printer has “Memory Switch” set which is software switches. Memory Switch set has “MSW 1”,“MSW 2”, “MSW 5”(Power OFF time selection), “MSW 6”(Power idle mode time selection),”MSW 7(MSR read mode selection)”, “MSW 8” and “Serial communication condition”.
3.2 Memory Switch 2 Switch 1~2 3 4~8 Function Interface selection (*1) Reserved Codepage selection (*2) ON OFF Refer to the following table Fixed to OFF Refer to the following table N OT ES (*1) Interface selection MSW 2-2 OFF OFF ON MSW 2-1 OFF ON OFF Function Bluetooth Interface RS-232C(serial) Interface USB Interface Desired code page can be select ed using Mem ory Swit ch 2- 4~ 8 by set t ing as following.
3.3 Memory Switch 5 (Power off time selection) MSW 5-8 MSW 5-7 MSW 5-6 MSW 5-5 MSW 5-4 MSW 5-3 MSW 5-2 MSW 5-1 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON OFF ON .. .. .. .. .. .. .. .. . . . . . . . . OFF OFF OFF OFF ON OFF ON OFF .. .. .. .. .. .. .. .. . . . . . . . . OFF OFF OFF ON OFF ON OFF OFF .. .. .. .. .. .. .. .. . . . . . . . . OFF OFF OFF ON ON ON ON OFF .. .. ..
3.
4. Self Test The self test let you know if your printer is operating properly. It checks the printing quality, ROM version and memory switch settings. The test is independent of any other equipment or software, so it is a good idea to run it when you first set up the printer or if you have any trouble. If the self test works correctly, the problem is in the other equipment or the software, not the printer.
6. Specifications Item Print method Print speed Resolution Paper supply method Character size Character per line Print Character sets Barcodes Paper roll Reliability Connectivity Battery charger Emulation Drivers Sensor Cutter type Language Paper type Width Diameter TPH Battery Interface Input Output Type Battery Output Charging time Dimension Printer Weight Printer Packing Accessories Unpacking Rev. 1.
7. Overall dimensions Rev. 1.
