Installation Instructions
Table Of Contents
- Introduction
- FCC Requirements
- Innovation, Science and Economic Development Canada Compliance
- Safety Precautions
- Information and Options
- Battery Installation and Removal
- Battery Care and Maintenance
- Antenna Installation and Removal
- Radio Controls
- LCD Display
- Programmable Switch and Button Functions
- Channel/Zone Selection Options
- Basic Radio Operation
- Command Zone Operation
- Code Guard/NAC Operation
- Mixed Mode Operation
- Trunking Channel Basic Operation
- Scan Options
- Pick List Options
- Unit-to-Unit Call Options
- Emergency Signaling Options
- Encryption Operation
- Messaging
- Paging and Call Alert
- Radio Inhibit/Enable [INH]/[UNINH]
- Other Options and Functions
- Backlight [LITE]
- Battery Life [LIFE]
- Bluetooth [BT]
- Busy Channel Operation
- Channel Select [CHAN]
- Cloning [CLON]
- Contrast
- Control Lockout [LCK]
- Date and Time [DATE]
- Global Positioning [GPS]
- Hard Power Down [PWRD]
- Keypad Programming
- Minimum Volume [VOL]
- Monitor [MON]
- Nuisance Channel Delete [DEL]
- Phone [PHN] and Hang Up [HANG]
- Radio Accountability Tone [RAT]
- Radio info
- Repeater Talkaround [T/A]
- Send Alert Tone [SNDT]
- Send Signal [SEND]
- Squelch Adjust [SQL]
- Site Display [STDS]
- Site Lock [STLK]
- Site Search [STSR]
- Surveillance Mode [SURV]
- System Test
- Transmit Digital [TXAD]
- Transmit Power [PWR]
- Two-Tone Select [TONE]
- Versions
- Zone Select [ZONE] (Conventional and Trunked Channels)
- Keypad Programming
- BK Technologies Warranty Information
- My Radio Settings
BK Technologies
- 6 -
If you are not using a body-worn accessory and are not using the radio
in the intended use position in front of the face, then ensure the antenna
and the radio are kept at least one inch (2.5 cm) from the body when
transmitting. Keeping the radio at the proper distance is important
because RF exposures decrease with increasing distance from the
antenna.
Changes or modications to the radio and/or equipment that is not
approved by BK Technologies could void the user's authority to operate
the radio.
Use only BK Technologies approved supplied or replacement antennas,
batteries, and accessories. Use of non-BK Technologies approved
antennas, batteries, and accessories may exceed the FCC RF
exposure guidelines.
For a list of BK Technologies approved accessories visit the following
website: http://www.bktechnologies.com.
The AMBE® voice compression software included in this product
is protected by intellectual property rights including patent rights,
copyrights and trade secrets of Digital Voice Systems, Inc. The user
of this software is explicitly prohibited from attempting to decompile,
reverse engineer, or disassemble the object code, or in any other way
convert the object code into a human-readable form. This software is
licensed solely for use within this product. US Patent Nos. #6,912,495
B2, #5,870,405, #5,826,222, #5,754,974, #5,715,365, #5,701,390,
#5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772,
#5,247,579, #5,226,084, and #5,195,166.
FCC ID
The BKR900 may contain the following modules under FCC ID: K95BKR9000
and Industry Canada (Inovation, Science, and Economic Development) ID:
2116A-BKR9000
Telit LTE Modem LE910C1 NS
FCC ID: RI7LE910C1NS
ISED: 5131A-LE910C1NS
Texas Instruments WiFi-BT Module WL1837MODGIMOCT
FCC ID: Z64-WL18DBMOD
ISED: 4511-WL18DBMOD
NXP NFC Controller PN7120
FCC ID: VPQ-PN7120
ISED: 7329A-PN7120
Contact Information
For additional information on exposure requirements or other
information, visit website http://www.bktechnologies.com.