Installation manual

D15 Oven temperature
Here it is possible to read the current oven temperature, P1. In the field next to ”Temperature”, the current
temperature is shown. If ERR appears, the sensor circuit is defective. In the field next to ”Time”, an
adjustment value between 80 and 120 (default 100) is shown. To
adjust the temperature, press the time key
until the digit in the display flashes. Then adjust upwards or downwards until the correct temperature is
shown. Finally, press the time key again to save the setting. The temperature can be adjusted by +- 50°F (+-
10°C).
TEST MODE D16-D20
D16 Core temperature (This
function is not available on B models).
C and K models can use only one core temperature probe, it is possible, however, to test core
temperature probes 1 and 2.
Here it is possible to read the current temperature of the core temperature sensor, P2 + P2A. In the field next
to ”Temperature”, the current temperature is shown. If ERR appears, the sensor circuit is defective. In the
field next to ”Time”, an adjustment value between 80 and 120 (default 100) is shown. To adjust the
temperature, press the time key until the digit in the display flashes. Then adjust upwards or
downwards
until the correct temperature is shown. Finally, press the time key again to save the setting.
The temperature can be adjusted by +- 50°F (+- 10°C). You change between the various measuring points
of the core temperature probe by pressing the step key.
1= Core temp.probe 1, point 1,
2= Core temp.probe, point 2, 3= Core temp.probe 1, point 3.
4= Core temp.probe 2, point 1, 5= Core temp.probe, point 2, 6= Core temp.probe 2, point 3.
D17 Steam generator temperature (Available on K models only).
Here it is possible to read the current steam generator temperature, P3.
In the field next to ”Temperature”,
the current temperature is shown. If ERR appears, the sensor circuit is defective. In the field next to ”Time”,
an adjustment value between 80 and 120 (default 100) is shown. To adjust the temperature, press the time
key until the digit in the display flashes.
Then adjust upwards or downwards until the correct temperature is
shown. Finally, press the time key again to save the setting. The temperature can be adjusted by +-50°F (+-
10°C).
D18 Drain temperature
Here it is possible to read the current steam generator temperature, P4. In the field next to ”Temperature”,
the current temperature is shown. If ERR appears, the sensor circuit is defective. In the field next to ”Time”,
an adjustment value between 80 and 120 (default 100) is shown. To adjust the temperature, press the time
key until the digit in the display flashes. Then adjust upwards or downwards until
the correct temperature is
shown. Finally, press the time key again to save the setting. The temperature can be adjusted by +- 50°F (+-
10°C) (approx. 33°F [0.5°C] per step).
D20 Door sensor
Here it is possible to read the status of and calibrate door sensor 1 = SE1 and 2
= SE1A. You change
between door sensor 1 and 2 by pressing the step key. After some time, the text “DOOR SENSOR” changes
to show the status of the sensor: >CLOSED<, >OPEN<, >SENS ERROR<. You start the calibration by
pressing the exhaust key.
How to calibrate:
1. Press damper key
2. >CLOSE< flashes 3. Close the door
4. Press damper key 5. >OPEN< flashes 6. Open door in the first step
7. Press damper key 8. >CALIB OK< or >CALIB ERR< appears
9. Press damper key to confirm
In the display next to the temperature key, it is possible to read the current value (0 – 120). In the display
next to the time key, it is possible to read the set point.
TEST FUNCTIONS D21-28
D21 Water level (Available on K models only).
Here
it is possible to read the status of Se2. In the display next to ”Time”, the conductivity is shown and it is
indicated whether the water level is high or low. XX|LO= low water level, XX|HI= high water level. XX =
conductivity of the water. Default setting is approx. 80
with no water and 40.60 with water. The better the
13