March LB308A 2009 codes codes codes codes codes codes 8-Port 10/100BASE-TX Hardened Ethernet Extender Switch Headline User’s Manual text. BLACK BOX Use Subheadline this managed text to hardened be added. switch plus VDSL extender ® in extreme environments. Customer Support Information Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
FCC and NOM Statements FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
NOM Statement 5. El aparato eléctrico no deberá ser usado cerca del agua — por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc. 6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante. 7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante. 8.
NOM Statement 17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación. 18.
Trademarks Used in this Manual Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Apple and Macintosh are registered trademarks of Apple Computer, Inc. Hyperterminal is a registered trademark of Hilgraeve, Inc. Internet Explorer is a registered trademark of Microsoft Corporation. Netscape is a registered trademark of Netscape Communications Corporation. UNIX is a registered trademark of The Open Group.
Quick Start Guide Quick Start Guide This quick start guide describes how to install and use the 8-Port 10/100BASE-TX Hardened Ethernet Extender Switch. Use it in harsh environments where space is limited. QS.1 Physical Description Figure QS-1 illustrates the port status LEDs and power inputs. Tables QS-1 and QS-2 describe these components. 321 4 5 12 10 9 8 11 7 6 13 13 13 13 Figure QS-1. Port status LEDs and power inputs. Page 6 724-746-5500 | blackbox.
Quick Start Guide Table QS-1. Port status LEDs. Number Indicator State Indication 1 Power 1 Steady Power on. 2 Power 2 3 Power 3 Off Power off. Steady A valid network connection is established. Flashing Transmitting or receiving data. ACT stands for Activity. Steady Connection at 100-Mbps speed. Off Connection at 10-Mbps speed. Steady A valid network connection is established. Flashing Transmitting or receiving data. ACT stands for Activity.
Quick Start Guide Table QS-3. Ports on the switch. Number Number of Ports Description Mode Selection 10BASE-T full-duplex mode 10BASE-T half-duplex mode 12 (8) RJ-45 10/100BASE-TX ports 100BASE-TX full-duplex mode 100BASE-TX half-duplex mode Auto-negotiating mode 13 (2) RJ-11 and terminal blocks Ethernet Extender ports Asymmetrical or symmetrical DC Terminal Block Power Inputs: You can use two power inputs to power on the Hardened Ethernet Extender Switch. Redundant power supplies are supported.
Quick Start Guide • Provides 2 MB of memory buffer. • Relay output alarms indicate power and port link failure. • Includes redundant 12–48-VDC power terminal block power inputs and 12-VDC jack with a 100–240-VAC external power supply. • Operating voltage and maximum current consumption are: 0.92 A @ 12-VDC, 0.46 A @ 24 VDC, 0.23 A @ 48 VDC. Maximum power consumption is 11 W. • Operating temperature range is -40 to +167° F (-40 to +75° C). • Supports DIN rail and panel mounting installation. QS.3.
Quick Start Guide Figure QS-2. switch_a> prompt. 5. Log on to Privileged Exec Mode (Enable Mode): At the “switch_a>” prompt, type “enable” and press “Enter” to log on to Privileged Exec Mode (or Enable Mode). The “switch_all” prompt will show on the screen. 6. Log on to Configure Mode (Configure Terminal Mode): At the “switch_all” prompt, just type in “configure terminal” and press Enter to log on to Configure Mode (or Configure Terminal Mode). The “switch_a(config)#” prompt will show on the screen.
Quick Start Guide QS.4 Web Configuration 1. Log in to the Ethernet Switch: Specify the default IP address (192.168.1.10) of the Hardened Ethernet Extender Switch in the Web browser. A login will appear as shown in Figure QS-4. Figure QS-4. Login screen. 2. Enter the factory default login ID: root. Enter the factory default password (no password), then click on the “Login” button to log in to the Hardened Ethernet Extender Switch. LB308A 724-746-5500 | blackbox.
Quick Start Guide Figure QS-5. Welcome screen. Page 12 724-746-5500 | blackbox.
Preface Preface This manual describes how to install and use the 8-Port 10/100BASE-TX Ethernet Extender. The extender is scalable and uses SNMP/RMON Web-based management. To get the most from this manual, you should have an understanding of Ethernet networking concepts. In this manual, you will find: • Specifications • Illustrated LED functions. • Installation instructions. • Management configuration. • SNMP, IGMP LB308A 724-746-5500 | blackbox.
Table of Contents Table of Contents Quick Start Guide ......................................................................................... 6 QS.1 Physical Description........................................................................... 6 QS.2 Functional Description....................................................................... 8 QS.3 Console Configuration...................................................................... 9 QS.4 Web Configuration.........................................
Table of Contents 4.5 4.6 Protocols ....................................................................................... 33 Management Architecture.............................................................. 34 5. Web-Based Browser Management............................................................. 35 5.1 SNMP and RMON Management..................................................... 35 5.1.1 Overview........................................................................ 35 5.1.
Table of Contents Apppendix A. DB9 DCE Pin Assignment........................................................... 203 Appendix B. Time Zone, Country, and City Lists............................................... 204 Page 16 724-746-5500 | blackbox.
Chapter 1: Specifications 1. Specifications Address Table Size — 8192 MAC addresses Cable — 10BASE-T: 2-pair UTP/STP CAT3/4/5, up to 328 ft. (100 m); 100BASE-TX: 2-pair UTP/STP CAT5, up to 328 ft. (100 m); Ethernet Extender: Telephone wires up to 6232 ft.
Chapter 1: Specifications Size — 5.7"H x 2.4"W x 4.9"D (14.5 x 6 x 12.5 cm) Weight — 2.4 lb. (1.1 kg) Page 18 724-746-5500 | blackbox.
Chapter 2: Overview 2. Overview 2.1 Introduction Use the 8-Port 10/100BASE-TX Hardened Ethernet Extender Switch in harsh environments where space is limited. 2.2 Features The Hardened Ethernet Extender Switch: • Meets NEMA TS1/TS2 environmental requirements, including temperature, shock, and vibration for traffic control equipment. • Meets EN61000-6-2 and EN61000-6-4 EMC generic standard immunity for an industrial environment. • Manageable via SNMP, Web browser, Telnet, and RS-232 console port.
Chapter 2: Overview 2.3 Management Support The 8-Port 10/100BASE-TX Hardened Ethernet Extender Switch supports VLAN, trunking, port security, port mirroring, QoS, internetworking protocols, and network management methods. VLAN: • Port-based VLAN • IEEE 802.1q tagged VLAN Trunking: • MAC-based trunking with automatic link failover Port Security: • Per-port programmable MAC address locking • Up to 24 static secure MAC addresses per port • IEEE 802.
Chapter 2: Overview • SNMP agent: MIB-2 (RFC1213); bridge MIB (RFC1493); RMON MIB (RFC2819): statistics, history, alarm, and events; VLAN MIB (IEEE 802.1Q/RFC2674), private MIB • Web browser • TFTP software upgrade capability 2.4 What’s Included Your package should contain the following items. If anything is missing or damaged, contact Black Box Technical Support at 724-746-5500 or info@blackbox.com.
Chapter 2: Overview Table 2-1. Port status LEDs. Number Indicator State Indication 1 Power 1 Steady Power on. 2 Power 2 3 Power 3 Off Power off. Steady A valid network connection is established. Flashing Transmitting or receiving data. ACT stands for Activity. Steady Connection at 100-Mbps speed. Off Connection at 10-Mbps speed. Steady A valid network connection is established. Flashing Transmitting or receiving data. ACT stands for Activity.
Chapter 2: Overview Table 2-3. Ports on the switch. Number Number of Ports Description Mode Selection 10BASE-T full-duplex mode 10BASE-T half-duplex mode 12 (8) RJ-45 10/100BASE-TX ports 100BASE-TX full-duplex mode 100BASE-TX half-duplex mode Auto-negotiating mode 13 (2) RJ-11 and terminal blocks Ethernet Extender ports Asymmetrical or symmetrical 10/100BASE-T and Ethernet Extender Connectors Figure 2-2 illustrates the 10/100BASE-T RJ-45 connector. Table 2-4 describes the connector pinouts.
Chapter 2: Overview Figure 2-3. Ethernet Extender RJ-11 and terminal block connectors. Table 2-5. RJ-11 and terminal block port pinouts. Pin Signal 3 Tip 4 Ring WARNING: Improper operation might damage the terminal block. Ethernet Extender Mode Settings You can set the Ethernet Extender modes via DIP switches on the front panel of the Hardened Ethernet Extender Switch. Table 2-6. DIP switch settings. Page 24 Loc Rmt The device operate in local mode. The device operates in remote mode.
Chapter 2: Overview 2.6 Hardened Ethernet Extender Switch Management 2.6.1 Web-Based Browser Interface The Hardened Ethernet Extender Switch has a point-and-click, browser-based interface that lets users access full Hardened Ethernet Extender Switch configuration and functionality from a Netscape® or Internet Explorer® browser. 2.6.
Chapter 3: Installation 3. Installation This chapter gives step-by-step instructions for installing the Hardened Ethernet Extender Switch. 3.1 Selecting a Site for the Hardened Ethernet Extender Switch As with any electric device, you should place the Hardened Ethernet Extender Switch where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference.
Chapter 3: Installation Figure 3-1. Switch mounted on a DIN rail. 3.3 Connecting to Power The switch is powered via redundant DC Terminal Block Power Inputs or a 12-VDC DC Jack. 3.3.1 12-VDC Jack Step 1: Connect the supplied AC to DC power adapter to the receptacle on the top side of the Hardened Ethernet Extender Switch. Step 2: Connect the power cord to the AC to DC power adapter and attach the plug into a standard AC outlet with the appropriate AC voltage. 3.3.
Chapter 3: Installation Ethernet Extender Switch. 1 3 4 5 2 Figure 2-3. Power connectors on the switch. 3.3.3 Alarms for Power Failure Step 1: There are two pins on the terminal block used to detect a power failure. The output is normally closed when the power source is active. Use this as a drycontact application to send a signal that detects a power failure. Table 3-1. Power input assignment.
Chapter 3: Installation SPECIAL NOTE: The relay output is in the normally open position when there is no power to the Hardened Ethernet Extender Switch. Do not connect any power source to this terminal to prevent shorting your power supply. 3.3.4 Reset Button Press the reset button for more than 10 seconds to reset the Hardened Ethernet Extender Switch back to the default password. 3.4 Connecting to Your Network 3.4.
Chapter 3: Installation Step 2: Prepare cable with corresponding connectors for each type of port in use. Step 3: Consult Table 3-2 for cabling requirements based on connectors and speed. Step 4: Connect one end of the cable to the Hardened Ethernet Extender Switch and the other end to a desired device. Step 5: Once the connections between two end devices are made successfully, turn on the power and the Hardened Ethernet Extender Switch is ready to operate. Page 30 724-746-5500 | blackbox.
Chapter 4: Hardened Ethernet Extender Switch Management 4. Hardened Ethernet Extender Switch Management This chapter explains the methods that you can use to configure management access to the Hardened Ethernet Extender Switch. It describes the types of management applications and the communication and management protocols that deliver data between your management device (workstation or personal computer) and the system. It also contains information about port connection options.
Chapter 4: Hardened Ethernet Extender Switch Management 4.2.1 Direct Access Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a terminal-emulation program (such as HyperTerminal) to the Hardened Ethernet Extender Switch console port.
Chapter 4: Hardened Ethernet Extender Switch Management After you set up your IP address for the Hardened Ethernet Extender Switch, you can access the Hardened Ethernet Extender Switch’s Web interface applications directly in your Web browser by entering the IP address of the Hardened Ethernet Extender Switch.
Chapter 4: Hardened Ethernet Extender Switch Management Simple Network Management Protocol (SNMP) SNMP is the standard management protocol for multivendor IP networks. SNMP supports transaction-based queries that allow the protocol to format messages and to transmit information between reporting devices and data-collection programs. SNMP runs on top of the User Datagram Protocol (UDP), offering a connectionless-mode service. 4.
Chapter 5: Web-Based Browser Management 5. Web-Based Browser Management The Hardened Ethernet Extender Switch provides a Web-based browser interface for configuring and managing the Hardened Ethernet Extender Switch. This interface allows you to access the Hardened Ethernet Extender Switch using a preferred Web browser. This chapter describes how to configure the Hardened Ethernet Extender Switch using its Web-based browser interface. 5.
Chapter 5: Web-Based Browser Management • Setting MIB variables according to the SNMP SET frame message. • Generating an SNMP TRAP frame message to the Network Management Station if the threshold of a certain MIB counter is reached or if other trap conditions (such as the following) are met: WARM START COLD START LINK UP LINK DOWN AUTHENTICATION FAILURE RISING ALARM FALLING ALARM TOPOLOGY ALARM MIB-II defines a set of manageable objects in various layers of the TCP/IP protocol suites.
Chapter 5: Web-Based Browser Management • RMON Alarm Group—allows a network administrator to define alarm thresholds for any MIB variable. An alarm can be associated with low threshold, high threshold, or both. A trigger can trigger an alarm when the value of a specific MIB variable exceeds a threshold, falls below a threshold, or exceeds or falls below a threshold. • RMON Event Group—allows a network administrator to define actions based on alarms. SNMP traps are generated when RMON alarms are triggered.
Chapter 5: Web-Based Browser Management 5.2.1 Logging on to the Hardened Ethernet Extender Switch Figure 5-1. Login screen. Hardened Ethernet Extender Switch IP ADDRESS: In your Web browser, specify the IP address of the Hardened Ethernet Extender Switch. Default IP address is 192.168.1.10. LOGIN: Enter the factory default login ID: root. PASSWORD: Enter the factory default password (no password).
Chapter 5: Web-Based Browser Management Figure 5-2. Web browser interface screen.
Chapter 5: Web-Based Browser Management OTHER PROTOCOLS: GVRP, IGMP Snooping, NTP 5.2.3 System Figure 5-3. System screen. System Information: View System information, VLAN ID, IP Address, and IP Subnet Page 40 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Mask of the Hardened Ethernet Extender Switch. Figure 5-4. Update setting screen. System Name/Password 1. System Name: Click in the “System Name” text box. Type a system name if it is blank, or replace the current system name with a new one. 2. Updating setting: Click the “Updating setting” button to update your settings. 3. Password: Click in the “Password” text box. Type a password. 4. Retype Password: Click in the “Retype Password” text box.
Chapter 5: Web-Based Browser Management Figure 5-5. Update setting screen. IP Address 1. IP Address: Click in the “IP Address” text box and type a new address to change the IP Address. 2. IP Subnet Mask: Click in “IP Subnet Mask” text box and type a new address to change the IP Subnet Mask. 3. Submit: Click on the “Submit” button when you finish these selections. 4.
Chapter 5: Web-Based Browser Management 6. Submit: Click “Submit” button when you finish with Default Gateway. 7. DNS Server: Click on the“DNS Server” drop-down menu to choose “Disable” or “Enable” from the “DNS Server” drop-down list to disable or enable DNS Server Setting for the Hardened Ethernet Extender Switch. Click the text box and type a new address to change the DNS Server. (Need to choose “Enable” from the “DNS Server” drop-down menu.) 8.
Chapter 5: Web-Based Browser Management C Figure 5-7. Route table screen. Route Table: Click Route Table to view Route Table. Page 44 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-8. Save configuration screen. Save Configuration 1. Load config from TFTP server: Click in the “TFTP Server” text box and type the TFTP server IP address from where the file will be obtained. Click in the “FILE” text box and type the name of the file that will be obtained. Click on the “Load” button to load the file from the TFTP server. 2.
Chapter 5: Web-Based Browser Management 5. Auto save: Click on the “Auto save” drop-down menu to choose “Disable” or “Enable” from the “Auto save” drop-down list to disable or enable Auto save for the Hardened Ethernet Extender Switch. 6. Auto save interval (5–65536 sec): Click in the “Auto save interval” text box and type a decimal number between 5 and 65536. 7. Submit: Click on the “Submit” button when you finish the Auto save configuration. Figure 5-9. Upgrade firmware screen. Firmware Upgrade 1.
Chapter 5: Web-Based Browser Management 3. Upgrade: Click on the “upgrade” button to upgrade firmware to the Hardened Ethernet Extender Switch. Follow the message on the screen during the firmware upgrade process. Do not turn off the power or perform other functions during this period of time. Reboot the Hardened Ethernet Extender Switch after completing the upgrade process. Figure 5-10. Firmware version screen. Follow the messages on the screen during the firmware upgrade process.
Chapter 5: Web-Based Browser Management Figure 5-11. Firmware upgrade screen #1. Page 48 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-12. Firmware upgrade screen #2. Firmware has been upgraded successfully to the Hardened Ethernet Extender Switch. Reboot the switch after completing the upgrade process. LB308A 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-13. Firmware upgrade screen #3. Page 50 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-14. Alarm setting screen. Alarm Setting 1. Name: Click on the “Name” drop-down menu to choose “fe1–fe8,” “VDSL1– VDSL2,” or “Power1–Power3” from the “Name” drop-down list. 2. Trigger Enabled: Click on the “Trigger Enabled” drop-down menu to choose “YES” or “NO” from the “Trigger Enabled” drop-down list to enable or disable Trigger. 3. Update Setting: Click on the “Update Setting” button to update settings to the Hardened Ethernet Extender Switch.
Chapter 5: Web-Based Browser Management Figure 5-15. Reboot screen. Reboot Reboot: Click on the “Reboot” button to restart the Hardened Ethernet Extender Switch. Page 52 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-16. Logout screen. Logout Logout: Click on the “Logout” button to logout of the Hardened Ethernet Extender Switch. LB308A 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management 5.2.4 Port Figure 5-17. Port Configuration screen. Configuration 1. Admin Setting: Click on the “Admin Setting” drop-down menu to choose “Link down” or “Link up” from the “Admin Setting” drop-down list to disable or enable Admin Setting for the port. 2. Speed: Click on the “Speed” drop-down menu to change the line speed and duplex settings from the “Speed” drop-down list for the port. 3.
Chapter 5: Web-Based Browser Management Figure 5-18. Port Status screen. Port Status View the link status, speed, duplex, and flow control status for all ports. LB308A 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-19. Rate Control screen. Rate Control 1. Ingress: Click in the “Ingress” text box and type a new Rate to change the Ingress Rate Control for the port. Rate Values: 64kbps, 128kbps, 192kbps, … , 1792kbps. 2Mbps, 3Mbps, 4Mbps, … , 100Mbps. NOTE: M = 1024k. 2. Egress: Click in the “Egress” text box and type a new Rate to change the Egress Rate Control for the port. Rate Values: 64kbps, 128kbps, 192kbps, … , 1792kbps. 2Mbps, 3Mbps, 4Mbps, … , 100Mbps.
Chapter 5: Web-Based Browser Management Figure 5-20. RMON Statistics screen. RMON Statistics Click Port 1–Port 10 to view corresponding RMON Statistics. LB308A 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-21. Per port VLAN activities screen. Per port VLAN activities Click Port 1–Port 10 to view corresponding VLAN activities. Page 58 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-22. Port Security screen. Port Security 1. Mode: Choose “Enable” or “Disable” from the “Mode” drop-down menu to enable or disable Port Security for the port. 2. Add MAC address: Click in the “Add MAC address” text box and type a MAC address for the port. 3. Delete MAC address: Choose a MAC address from the “Delete MAC address” drop-down menu to be deleted from the port. 4.
Chapter 5: Web-Based Browser Management 5.2.5 Switching Figure 5-23. Bridging screen. Bridging 1. Aging Time (seconds): Click the text box and type a decimal number as Bridging Aging Time in seconds. 2. Update setting: Click on the “update setting” button when you finished Aging Time settings. 3. Threshold level (0-100): Click in the “Level” text box and type a decimal number for the port. Choose “Broadcast” and/or “DFL-Multicast“ from “Stormcontrol enabled type” for the port.
Chapter 5: Web-Based Browser Management Figure 5-24. Static MAC entry screen. Static MAC Entry Static-MAC-Entry Forward: 1. Add MAC address: Click in the “Add MAC address” text box and type a locked forwarding MAC address for the port. 2. VLAN ID: Click on the “VLAN ID” drop-down menu and choose a VLAN ID from the “VLAN ID” drop-down list. 3. Delete MAC address: Choose a locked forwarding MAC address from the “Delete MAC address” drop-down menu to be deleted from the port. 4.
Chapter 5: Web-Based Browser Management 2. VLAN ID: VLAN ID: Choose a VLAN ID from the “VLAN ID” drop-down menu. 3. Delete MAC address: Choose a MAC address from the “Delete MAC address” drop-down menu to be discarded from the VLAN. 4. Submit: Click on the “Submit” button when you finish the Static-MAC-Entry Discard settings. Figure 5-25. Port Mirroring screen. Port Mirroring 1. Mirror From: Choose Mirror From port from Port 1–Port 10. 2.
Chapter 5: Web-Based Browser Management 4. Submit: Click on the “Submit” button when you finish the Port Mirroring settings. 5.2.6 Trunking Figure 5-26. Port Trunking screen. Port Trunking Static Channel Group: 1. Trunk 1: Click Port 1–Port 8 to assign ports to Trunk 1. (Maximum 4 ports in Trunk 1.) VDSL Trunking: 1. Trunk 3: Click “Static” or “Disable” for Trunk 3. 2. Submit: Click “Submit” button when you finished Port Trunking settings. LB308A 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management 5.2.7 STP Ring Figure 5-27. Global Configuration screen. Global Configuration 1. Spanning Tree Protocol: Choose “Enable” or “Disable” from “Spanning Tree Protocol” drop-down menu to enable or disable Spanning Tree Protocol. 2. Bridge Priority (0..61440): Click in “Bridge Priority” text box and type a decimal number between 0 and 61440. 3. Hello Time (sec) (1..9): Click in “Hello Time” text box and type a decimal number between 1 and 9. 4. Max Age (sec) (6..
Chapter 5: Web-Based Browser Management 6. STP Version: Click on the “STP Version” drop-down menu to choose “MSTP,” “RSTP,” or “STP compatible” from the “STP Version” drop-down list. 7. Update setting: Click on the “Update setting” button when you finish the Global Configuration. Figure 5-28. RSTP Port Setting screen RSTP Port Setting 1. STP Version: Click on the “STP Version” drop-down menu to choose “RSTP” from “STP Version” drop-down list. 2.
Chapter 5: Web-Based Browser Management 5. Point to Point Link: Click on the “Point to Point Link” drop-down menu to Choose “Enable” or “Disable” from “Point to Point Link” drop-down list to enable or disable Point to Point Link for the port. 6. Edge Port: Click on the “Edge Port” drop-down menu to Choose “Enable”, “Disable”, or “Auto” from “Edge Port” drop-down list to set Enable, Disable, or Auto Edge Port for the port. 7.
Chapter 5: Web-Based Browser Management Figure 5-30. MSTP Properties screen. MSTP Properties 1. STP Version: Click on the “STP Version” drop-down menu to choose “MSTP” from “STP Version” drop-down list. 2. Region Name: Click in the “Region Name” text box to create an MST region and specify a name to it. MST bridges of a region form different spanning trees for different VLANs. By default, each MST bridge starts with the region name as its bridge address.
Chapter 5: Web-Based Browser Management Figure 5-31. VLAN Interface Configuration screen #1. Figure 5-32. VLAN Interface Configuration screen #2. Page 68 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management MSTP Instance Setting VLAN Instance Configuration 1. VLAN Instance Configuration: Click on the “VLAN Instance Configuration” button. The “VLAN Instance Configuration” window appears. 2. VLAN ID: Click on the “VLAN ID” drop-down menu to choose VLAN from the “VLAN ID” drop-down list to simultaneously add multiple VLANs for the corresponding instance of a bridge. 3. Instance ID (1..15): Click in the “Instance ID” text box to specify the instance ID. 4.
Chapter 5: Web-Based Browser Management Figure 5-33. Port Instance Configuration screen. Page 70 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-34. Port Instance Configuration Instance ID screen. MSTP Port Setting Port Instance Configuration 1. Instance ID: Click on the “Instance ID” drop-down menu to choose instance ID from the “Instance ID” drop-down list. 2. Click Port 1– Port 8 to assign ports to the corresponding instance ID. 3. Update setting: Click on the “Update setting” button when you finish Port Instance Configuration. Instance ID 1.
Chapter 5: Web-Based Browser Management MSTP Port Configuration 1. Port: Click on the “Port” drop-down menu to choose port from the “Port” drop-down list. 2. Priority (Granularity 16): Click in the “Priority” text box to set the port priority for a bridge group. The Multiple Spanning Tree Protocol uses port priority as a tiebreaker to determine which port should forward frames for a particular instance on a LAN, or which port should be the root port for an instance.
Chapter 5: Web-Based Browser Management Ring Setting Ring state 1. Click on the “Ring state” drop-down menu from “Ring state” drop-down list to choose “Enable” or “Disable” to enable or disable Ring state. 2. Update setting: Click on the “Update setting” button when you finish Ring state setting. Set ring port 1. Ring port 1: Click on the “Ring port 1” drop-down menu to choose Ring port 1 from “Ring port 1” drop-down list. 2.
Chapter 5: Web-Based Browser Management VLAN Mode Setting 1. VLAN Mode Setting: Click on the “VLAN Mode Setting” drop-down menu to choose “Tag-based VLAN” or “Port-based VLAN” from “VLAN Mode Setting” drop-down list. 2. Update Setting: Click on the “Update Setting” button when you finish VLAN Mode Setting. Figure 5-37. Update VLAN Mode Setting screen. Page 74 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-38. Submit VLAN Setting screen. 802.1Q VLAN Setting Add VLAN: 1. VLAN setting: Click on “VLAN setting.” The “VLAN Setting” window appears. 2. Add VLAN: Click “Add VLAN” button to create a new VLAN from the “VLAN Setting” window. 3. VLAN ID (2–4094): Click in the “VLAN ID” text box and specify a new VLAN ID number from 2–4094. 4. VLAN Name: Click in the “VLAN Name” text box and type a name for this newly created VLAN.
Chapter 5: Web-Based Browser Management Figure 5-39. 802.1Q VLAN Setting screen. Delete VLAN: 1. VLAN setting: Click on “VLAN setting.” The “VLAN Setting” window appears. 2. Delete VLAN: Click on the “Delete VLAN” button. 3. Select a VLAN ID: Click on the “Select a VLAN ID” drop-down menu from “Select a VLAN ID” drop-down list to choose the VLAN to be deleted. 4. Submit: Click on the “Submit” button when you finish the VLAN setting. Page 76 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-40. Update VLAN Port Setting screen. 802.1Q Port Setting 1. VLAN Port Setting: Click “VLAN Port Setting.” The “VLAN Port Setting” window appears. 2. Mode: Click on the “Mode” drop-down menu to choose “Access,” “Trunk,” or “Hybrid” from the “Mode” drop-down list for the port. The port will be a Tag port if you choose “Trunk” Mode for the port. And the port will be a Tag or Untag port if you choose “Hybrid” Mode for the port. 3.
Chapter 5: Web-Based Browser Management Figure 5-41. Submit VLAN Mode Setting screen. Figure 5-42. VLAN Mode 2 screen. Page 78 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Port Based VLAN 1. VLAN: Choose the port to be added to or deleted from the VLAN. 2. Select all: Click on the “select all” button to choose Port 1–Port 10 to be added to the VLAN. 3. Delete all: Click on the “delete all” button to choose Port 1– Port 10 to be deleted from the VLAN. 4. Submit: Click on the “Submit” button when you finish Port Based VLAN setting. 5.2.9 QoS Figure 5-43. Global Configuration screen. Global Configuration 1.
Chapter 5: Web-Based Browser Management 2. Trust: Enable or disable the Hardened Ethernet Extender Switch port to trust the CoS (Class of Service) labels of all traffic received on that port. Enable or disable a routed port to trust the DSCP (Differentiated Service Code Point) labels of all traffic received on that port. 3. Policy: Choose “Strict Priority(Queue3) + WRR(Queue0-2)” or “WRR(Queue0-3)”. A strict priority queue is always emptied first.
Chapter 5: Web-Based Browser Management 2. Submit: Click on the “Submit” button when you finish 802.1p priority. Figure 5-45. DSCP screen. DSCP 1. Priority: Click on the “Priority” drop-down menu from the “Priority” drop-down list to choose 0–3 for DSCP Priority 0–63. 2. Submit: Click on the “Submit” button when you finish DSCP. LB308A 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management 5.2.10 SNMP Figure 5-46. SNMP General Setting screen. SNMP General Setting 1. SNMP Status: Click on the “SNMP Status” drop-down menu from the “SNMP Status” drop-down list to choose “Enable” or “Disable” to enable or disable SNMP. 2. Description: Click in the “Description” text box and specify a new description for SNMP. 3. Location: Click in the “Location” text box and specify a new location for SNMP. 4.
Chapter 5: Web-Based Browser Management 5. Trap Community Name: For each “Trap Community Name,” Click in the “Trap Community Name” text box and specify a trap community name. 6. Trap Host IP Address: For each “Trap Host IP Address,” Click in the “Trap Host IP Address” text box and specify a trap host IP address. 7. Link Down Trap: Click on the“Link Down Trap” drop-down menu from “Link Down Trap” drop-down list to choose “Enable” or “Disable” to enable or disable link down trap. 8.
Chapter 5: Web-Based Browser Management 2. Set Community Name: Click in the “Set Community Name” text box and specify a set community name. 3. Update Setting: Click “Update Setting” button when you finished SNMP V1/ V2c Setting. Figure 5-48. Update SNMP v1/v2c Setting screen. Page 84 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-49. SNMP v3 Setting screen. SNMP v3 Add User: 1. Add User: Click on the“Add User” button. The “SNMP V3 Setting” window appears. 2. SNMP Version: Click on the“SNMP Version” drop-down menu from the “SNMP Version” drop-down list to choose “SNMPv3 No-Auth,” “SNMPv3 Auth-MD5,” “SNMPv3 Auth-SHA,” “SNMPv3 Priv Auth-MD5,” or “SNMPv3 Priv Auth-SHA.” • SNMPv3 No-Auth: Add a user using SNMP v3 without authentication.
Chapter 5: Web-Based Browser Management • SNMPv3 Priv Auth-SHA: Add a user using SNMP v3 with authentication and privacy. Click in the “Auth. Password” text box and specify an authentication password. Click in the “Privacy PassPhrase” text box and specify a privacy pass phrase. 3. User Name: Click in the “User Name” text box and specify a user name for a user using SNMP v3. 4. Access Mode: Click on the “Access Mode” drop-down menu from “Access Mode” drop-down list to choose “Read Only” or “Read/Write.
Chapter 5: Web-Based Browser Management 2. Select User Name: Click on the “Select User Name” drop-down menu from the “Select User Name” drop-down list to choose the user to be deleted from using SNMP v3. 3. Submit: Click on the “Submit” button when you finish user deletion. 5.2.11 802.1x Figure 5-51. Radius Configuration screen. Radius Configuration 1.
Chapter 5: Web-Based Browser Management Figure 5-52. Radius Server Setting screen. Add Radius: 1. Add Radius: Click on the “Add Radius” button. The “Radius Server Setting” window appears. 2. Radius Server IP: Click in the “Radius Server IP” text box and specify the IP address of the remote radius server host. 3. Radius Server Port: Click in the “Radius Server Port” text box and specify the UDP destination port for authentication requests. The host is not used for authentication if set to 0. 4.
Chapter 5: Web-Based Browser Management 5. Timeout <1–1000>: Click in the “Timeout” text box and specify the time interval (in seconds) that the Hardened Ethernet Extender Switch waits for the radius server to reply before retransmitting. Enter a value in the range 1 to 1000. 6. Retransmit <1–100>: Click in the “Retransmit” text box and specify the number of times a radius request is resent to a server if that server is not responding or responding slowly. Enter a value in the range 1 to 100. 7.
Chapter 5: Web-Based Browser Management Figure 5-54. Port Authetication screen. Port Authentication 1. Interface: Click on the “Interface” drop-down menu from “Interface” drop-down list to choose the port to be set port-based authentication. 2. Authentication State: Click on the “Authentication State” drop-down menu from the “Authentication State” drop-down list to choose “Enable” or “Disable” to enable or disable authentication state. 3.
Chapter 5: Web-Based Browser Management 6. Update Setting: Click on the “Update Setting” button when you finish portbased authentication setting. 5.2.12 VDSL Figure 5-55. VDSL Configuration. VDSL Configuration VDSL Ports: 1. Interface: Click on the “Interface” drop-down menu from “Interface” dropdown list to choose VDSL1 or VDSL2 port. 2. VDSL Retrain: Click on the “VDSL Retrain” button to try to get a higher link speed for Ethernet Extender port. VDSL Settings: • Enable Asymmetric Mode: 1.
Chapter 5: Web-Based Browser Management 2. Update Setting: Click “Update Setting” button to finish enabling asymmetric mode for an Ethernet Extender port. 3. Fixed Rate: Click on the “Fixed Rate” drop-down menu to disable fixed speed rate or select a fixed speed rate for an Ethernet Extender port from the “Fixed Rate” drop-down list. Fixed Rate: bps Disable 59 M/31 M 52 M/24 M 47 M/14 M 42 M/8 M 35 M/6 M 28 M/5 M 25 M/2 M 22 M/1 M 14 M/1 M 1 M/1 M 4.
Chapter 5: Web-Based Browser Management 1M 4. Fixed Rate: Click on the “Fixed Rate” drop-down menu to disable fixed speed rate or select a fixed speed rate for Ethernet Extender port from the “Fixed Rate” drop-down list. Fixed Rate: bps Disable 50M 40M 30M 25M 20M 15M 10M 5M 3M 1M 5. Update Setting: Click on the “Update Setting” button to finish Max. Speed and Fixed Rate settings. LB308A 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-56. VDSL Status screen. VDSL Status Click VDSL1 or VDSL2 to view Interface VDSL1 or VDSL2 status. Page 94 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management Figure 5-57. VDSL counters screen. VDSL Counters Click VDSL1 or VDSL2 to view Interface VDSL1 or VDSL2 counters. LB308A 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management 5.2.13 Other Protocols Figure 5-58. GVRP screen. GVRP GVRP Global Setting: 1. GVRP: Click on the “GVRP” drop-down menu from “GVRP” drop-down list to choose “Enable” or “Disable” to enable or disable GVRP (GARP VLAN Registration Protocol). Page 96 724-746-5500 | blackbox.
Chapter 5: Web-Based Browser Management 2. Dynamic VLAN creation: Click on the “Dynamic VLAN creation” drop-down menu from “Dynamic VLAN creation” drop-down list to choose “Enable” or “Disable” to enable or disable Dynamic VLAN creation. GARP (Generic Attribute Registration Protocol) provides IEEE802.1Q compliant VLAN pruning and dynamic VLAN creation on IEEE802.1Q trunk ports. 3. Update Setting: Click on the “Update Setting” button when you finish GVRP Global Setting. Per port setting (include LAG): 1.
Chapter 5: Web-Based Browser Management Figure 5-59. IGMP Snooping screen. IGMP Snooping 1. IGMP mode: Click on the “IGMP mode” drop-down menu from the “IGMP mode” drop-down list to choose “Disable,” “Passive,” or “querier” for the Hardened Ethernet Extender Switch. Disable: Disable IGMP on the Hardened Ethernet Extender Switch. Passive: The Hardened Ethernet Extender Switch with only multicast-data-forwarding capability. Querier: The Hardened Ethernet Extender Switch acts as the querier for the network.
Chapter 5: Web-Based Browser Management 5. Fast-leave: Click on the “fast-leave” drop-down menu from the “fast-leave” drop-down list to choose “Enable” or “Disable” for the Hardened Ethernet Extender Switch. Enabling this function will allow members of a multicast group to leave the group immediately when an IGMP Leave Report Packet is received by the Hardened Ethernet Extender Switch. IGMP querier: 1. Query-interval: Click in the “query-interval” text box and specify a new number from 1–18000.
Chapter 5: Web-Based Browser Management Figure 5-60. NTP screen. NTP NTP Setting: 1. NTP Status: Click on the “NTP Status” drop-down menu from “NTP Status” drop-down list to choose “Enable” or “Disable” to enable or disable NTP for the Hardened Ethernet Extender Switch. 2. NTP Server (IP Address or Domain name): Click in the “NTP Server” text box and specify the IP address or Domain name of NTP server. 3. Sync Time: Click “Sync Time” button to synchronize time with NTP server. 4.
Chapter 5: Web-Based Browser Management 5. Polling Interval (1–10080 min): Click in the “Polling Interval” text box and specify the polling interval. 6. Update Setting: Click on the “Update Setting” button when you finish NTP Setting. Daylight Saving Setting: 1.
Chapter 5: Web-Based Browser Management • Day: <1–31> Specifies from 1 to 31. • Hour: <0–23> Specifies from 0 to 23. • Minute: <0–59> Specifies from 0 to 59. 6. Update Setting: Click on the "Update Setting" button when you finish Daylight Saving Setting. NOTE: The “Week”, “Hour,” “Minute,” and “Day” fields would not accept the alphabetic characters (Like Jan, Feb, Sun, Mon). They only accept the two digit numbers (0 through 9). Page 102 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management 6. Command Line Console Management The Hardened Ethernet Extender Switch provides a command line console interface for configuration purposes. The Hardened Ethernet Extender Switch can be configured either locally through its RS-232 port or remotely via a Telnet session. For the latter, you must specify an IP address for the Hardened Ethernet Extender Switch first.
Chapter 6: Command Line Console Management 6.1.1 Exec Mode (View Mode) Figure 6-1. switch_a prompt. Logon to Exec Mode (View Mode) At the switch_a login: prompt just type in “root” and press to logon to Exec Mode (or View Mode). switch_a login: root Figure 6-2. switch_a> prompt. Page 104 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management Basic commands Exec Mode (or View Mode) is the base mode from where users can perform basic commands such as: clear, debug, disable, enable, exit, help, logout, no, quit, show, terminal. The CLI contains a text-based help facility. To access this help, type in the full or partial command string then type a question mark “?”. The CLI displays the command keywords or parameters along with a short description.
Chapter 6: Command Line Console Management Figure 6-4. switch_a>show ? prompt. Figure 6-5. switch_a>show prompt. Login timed out The login session to Exec Mode (or View Mode) has timed out due to an extended period of inactivity (60 seconds) to indicate authentication attempt timed out. And the switch_a login: prompt will show on the screen. Page 106 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management Logon back to Exec Mode (View Mode) At the switch_a login: prompt, type in “root” and press to logon back to Exec Mode (or View Mode). switch_a login: root Figure 6-6. Logon back to Exec Mode (View Mode) screen. Exit from Exec Mode (View Mode) At the switch_a> prompt, type in “exit” and press to exit from Exec Mode (or View Mode). switch_a>exit LB308A 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management Figure 6-7. Exit Exec Mode (View Mode) screen 6.1.2 Privileged Exec Mode (Enable Mode) Logon to Privileged Exec Mode (Enable Mode) At the switch_a> prompt, type in “enable” and press to logon to Privileged Exec Mode (or Enable Mode). The switch_a# prompt will show on the screen. switch_a>enable Figure 6-8. Logon to Privileged Exec Mode (Enable Mode). Page 108 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management Commands Privileged Exec Mode (or Enable Mode) allows users to run commands as follows. At the switch_a# prompt, press to list the commands. switch_a#? Figure 6-9. List commands screen. Figure 6-10. List commands screen prompt. LB308A 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management At the switch_a# prompt, type in the full or partial command string, then type a question mark “?” to display the command keywords or parameters along with a short description. switch_a#show ? Figure 6-11. Display command keywords or parameters. Figure 6-12. Short description screen. Page 110 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management Login timed out The login session to Privileged Exec Mode (or Enable Mode) has timed out because of an extended period of inactivity (60 seconds) to indicate authentication attempt timed out. The switch_a login: prompt will show on the screen. Logon back to Exec Mode (View Mode) At the switch_a login: prompt, type in “root” and press to logon back to Exec Mode (or View Mode). switch_a login: root F Figure 6-13. Logon back to Exec Mode (or View Mode).
Chapter 6: Command Line Console Management Figure 6-14. Exit Exec Mode (or View Mode). 6.1.3 Configure Mode (Configure Terminal Mode) Logon to Configure Mode (Configure Terminal Mode) At the switch_a# prompt, type in “configure terminal” and press to logon to Configure Mode (or Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. Figure 6-15. Logon to Configure Mode screen. Page 112 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management Commands Configure Mode (or Configure Terminal Mode) serves as a gateway into the modes as follows. At the switch_a(config)# prompt, press to list the commands. Figure 6-16. Configure mode screen #1. Figure 6-17. Configure mode screen #2 LB308A 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management At the switch_a(config)# prompt, type in the full or partial command string, then type a question mark “?” to display the command keywords or parameters along with a short description. switch_a(config)#show ? Figure 6-18. Display command keywords or parameters. Login timed out The login session to Configure Mode (or Configure Terminal Mode) has timed out because of an extended period of inactivity (60 seconds) to indicate authentication attempt timed out.
Chapter 6: Command Line Console Management Figure 6-19. Logon back to Exec Mode. Exit from Configure Mode (or Configure Terminal Mode) At the switch_a(config)# prompt, type in “exit” and press to exit from Configure Mode (or Configure Terminal Mode). switch_a(config)#exit Figure 6-20 Exit Configure Mode. LB308A 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management 6.2 System System Information, System Name/Password, IP Address, ARP Table, Route Table, Save Configuration, Firmware Upgrade, Alarm Setting, Reboot, Logout System Name/Password System Name: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use the hostname command to set or change the network server name.
Chapter 6: Command Line Console Management switch_a(config)# IP Address IP Address/IP Subnet Mask: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. vlan1.1 means vlan 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface vlan1.1 switch_a(config-if)# 2. Usage: Use the ip address command to remove the IP address from an interface. 3.
Chapter 6: Command Line Console Management 2. Usage: Use IP default-gateway command to set the IP address of the default gateway. Use the no ip default-gateway command to remove the IP address of the default gateway. 3. Command Syntax: ip default-gateway IP-ADDRESS no ip default-gateway IP-ADDRESS A.B.C.D specifies the IP address of the default gateway. 4. Example: The following example sets the default gateway 192.168.1.254 to Hardened Ethernet Extender Switch: switch_a(config)#ip default-gateway 192.168.
Chapter 6: Command Line Console Management switch_a(config)# ARP Table 1. Command Mode: Privileged Exec mode Logon to Privileged Exec Mode (Enable Mode). The switch_a# prompt will show on the screen. switch_a(config)# 2. Usage: Use show arp-table command to view ARP Table. 3. Command Syntax: show arp-table 4. Example: The following example shows the ARP Table of switch: switch_a#show arp-table Route Table 1. Command Mode: Privileged Exec mode Logon to Privileged Exec Mode (Enable Mode).
Chapter 6: Command Line Console Management Logon to Privileged Exec Mode (Enable Mode). The switch_a# prompt will show on the screen. switch_a# 2. Usage: Use install image command to load configuration file from tftp server to Hardened Ethernet Extender Switch. 3. Command Syntax: install image IP-ADDRESS WORD IP-ADDRESS specifies the IP address of tftp server. WORD specifies the file name to be loaded to Hardened Ethernet Extender Switch. 4.
Chapter 6: Command Line Console Management switch_a#write config-file 192.168.1.100 switch_a# Save Configuration: 1. Command Mode: Privileged Exec mode Logon to Privileged Exec Mode (Enable Mode). The switch_a# prompt will show on the screen. switch_a# 2. Usage: Use copy running-config startup-config command to write configurations to the file to be used at startup. This is the same as the write memory command. 3. Command Syntax: copy running-config startup-config 4.
Chapter 6: Command Line Console Management 4. Example: The following example restores default setting of the Hardened Ethernet Extender Switch: switch_a#restore default switch_a# Auto Save: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to enable auto save configuration function.
Chapter 6: Command Line Console Management 2. Usage: Use this command to set the interval when the configuration would be automatically saved. The range of interval value is from 5 to 65535. The default value is 30 seconds. 3. Command Syntax: service auto-config interval WORD WORD specifies the interval value. 4.
Chapter 6: Command Line Console Management Follow the message on the screen during the firmware upgrade process. Do not turn off the power or perform other functions during this period of time. Figure 6-21. Upgrade firmware screen. At the “switch_a#” prompt just type in “reload” and press to reboot the Hardened Ethernet Extender Switch after completing the upgrade process. Figure 6-22. Reload screen. Page 124 724-746-5500 | blackbox.
Chapter 6: Command Line Console Management Alarm Setting Alarm-trigger if: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to enable or disable alarm trigger on interface. 3. Command Syntax: (no) alarm-trigger if INTERFACE INTERFACE specifies the interface. 4.
Chapter 6: Command Line Console Management 4. Example: The following example enables alarm trigger of power “1” to the Hardened Ethernet Extender Switch: switch_a(config)#alarm-trigger power 1 switch_a(config)# Reboot 1. Command Mode: Privileged Exec mode Logon to Privileged Exec Mode (Enable Mode). The switch_a# prompt will show on the screen. switch_a# 2. Usage: Use reload command to restart the Hardened Ethernet Extender Switch. 3. Command Syntax: reload 4.
Chapter 6: Command Line Console Management 4. Example: The following example specifies to exit from the Exec mode or Privileged Exec mode. switch_a>logout switch_a login: 6.3 Port Configuration, Port Status, Rate Control, RMON Statistics, Per Port Vlan Activities, Port Security Configuration Admin Setting: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen.
Chapter 6: Command Line Console Management Duplex: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use duplex command to specify the duplex mode to be used for each interface. Use the no duplex to disable this function. 3. Command Syntax: (no) duplex MODE MODE specifies the duplex mode: auto, full, half. 4.
Chapter 6: Command Line Console Management 2. Usage: Use flowcontrol on command to enable flow control, and configure the flow control mode for the port. Use the no flowcontrol to disable this function. 3. Command Syntax: flowcontrol on no flowcontrol 4. Example: The following example shows the use of flowcontrol on to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#flowcontrol on switch_a(config-if)# Port Status 1.
Chapter 6: Command Line Console Management Rate Control 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use this command to specify the ingress/egress rate to be used for each interface. The bandwidth value is in bits.
Chapter 6: Command Line Console Management The switch_a> or switch_a# prompt will show on the screen. switch_a> switch_a# 2. Usage: Use the show interface statistics command to display RMON statistics of interface. 3. Command Syntax: show interface statistics IFNAME IFNAME specifies the name of the interface for which RMON statistics is desired. 4.
Chapter 6: Command Line Console Management Port Security Mode: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use this command to enable port security for port. Use the no parameter with this command to disable port security for port. 3. Command Syntax: port-security enable no port-security enable 4.
Chapter 6: Command Line Console Management 2. Usage: Use this command to add MAC addresses to be allowed to access the port. Use the no parameter with this command to delete MAC addresses to be allowed to access the port. 3. Command Syntax: port-security allowed-address MAC no port-security allowed-address MAC MAC the Media Access Control (MAC) address in the HHHH.HHHH.HHHH format. 4. Example: The following example adds MAC address 2222.2222.
Chapter 6: Command Line Console Management Group = <1-1> The ID of the bridge-group that this ageing time is for. AGEINGTIME = <10-1000000> The number of seconds of persistence. 4. Example: The following example sets the new AGEINGTIME (1000) to bridge GROUP (1): switch_a(config)#bridge 1 ageing-time 1000 switch_a(config)# Threshold level (0-100): 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1.
Chapter 6: Command Line Console Management 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use storm-control broadcast enable command to enable broadcast traffic. Use no storm-control broadcast command to disable broadcast traffic. 3.
Chapter 6: Command Line Console Management 2. Usage: Use storm-control multicast enable command to enable multicast traffic. Use no storm-control multicast command to disable multicast traffic. 3. Command Syntax: storm-control multicast enable no storm-control multicast 4. Example: The following example shows setting storm-control multicast enable to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#storm-control multicast enable switch_a(config-if)# DLF: 1.
Chapter 6: Command Line Console Management 4. Example: The following example shows setting storm-control dlf enable to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#storm-control dlf enable switch_a(config-if)# Static MAC Entry Static-MAC-Entry Forward: 5. Command Mode: Configure mode Log on to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 6.
Chapter 6: Command Line Console Management Static-MAC-Entry Discard: 1. Command Mode: Configure mode Log on to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to statically configure a bridge entry to discard matching frames in a particular VLAN. 3. Command Syntax: bridge GROUP address MAC discard vlan VLANID no bridge GROUP address MAC discard vlan VLANID GROUP <1-1> Bridge-group ID used for bridging.
Chapter 6: Command Line Console Management 2. Usage: Use this command to define a mirror source port and its direction. Use the no parameter with this command to disable port mirroring by the destination port on the specified source port. 3. Command Syntax: mirror interface SOURCEPORT direction SNOOPDIRECTION no mirror interface SOURCEPORT SOURCEPORT Name of the Source interface to be used. SNOOPDIRECTION [both|receive|transmit] both Specifies mirroring of traffic in both directions.
Chapter 6: Command Line Console Management 2. Usage: Use static-channel-group command to create a static aggregator, or add a member port to an already-existing static aggregator. Use the no static-channel-group command to detach the port from the static aggregator. 3. Command Syntax: static-channel-group <1-3> no static-channel-group <1-3> Channel group number. Maximum 4 ports in static-channel-group 1 and static-channel-group 2. Maximum 2 ports in static-channel-group 3 4.
Chapter 6: Command Line Console Management 3. Command Syntax: bridge GROUP protocol PROTOCOL vlan-bridge GROUP <1-1> Bridge group name used for bridging. PROTOCOL ieee IEEE 802.1Q spanning-tree protocol. mstp IEEE 802.1s multiple spanning-tree protocol. rstp IEEE 802.1w rapid spanning-tree protocol. 4. Example: The following example chooses the PROTOCOL (rstp) on bridge GROUP (1): switch_a(config)#bridge 1 protocol rstp vlan-bridge switch_a(config)# Multiple Spanning Tree Protocol: 1.
Chapter 6: Command Line Console Management 4. Example: The following example enables or disables the multiple-spanning-tree on bridge GROUP (1): switch_a(config)#bridge 1 multiple-spanning-tree enable switch_a(config)#no bridge 1 multiple-spanning-tree enable bridge-forward switch_a(config)# Rapid Spanning Tree Protocol: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2.
Chapter 6: Command Line Console Management Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to enable the Spanning Tree protocol on a bridge. Use the no form of the command to disable the Spanning Tree protocol on a bridge. 3. Command Syntax: bridge GROUP spanning-tree enable no bridge GROUP spanning-tree enable BRIDGE-FORWARD GROUP <1-1> Bridge group name used for bridging.
Chapter 6: Command Line Console Management GROUP <1-1> The ID of the bridge group for which the priority is set. PRIORITY <0-61440> The bridge priority. 4. Example: The following example sets the priority PRIORITY (4096) of bridge GROUP (1): switch_a(config)#bridge 1 priority 4096 switch_a(config)# Hello Time (sec) (1..9): 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2.
Chapter 6: Command Line Console Management switch_a(config)# 2. Usage: Use this command to set the max-age for a bridge. Use the no parameter with this command to restore the default value of max-age. 3. Command Syntax: bridge GROUP max-age MAXAGE no bridge GROUP max-age GROUP <1-1> The ID of the bridge group to which this maximum age time is assigned. MAXAGE <6-28> The maximum time, in seconds, to listen for the root bridge. 4.
Chapter 6: Command Line Console Management FORWARD_DELAY <4-30> the forwarding time delay in seconds. 4. Example: The following example sets the forward-time FORWARD_DELAY (30) of bridge GROUP (1): switch_a(config)#bridge 1 forward-time 30 switch_a(config)# RSTP Port Setting Priority(Granularity 16): 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen.
Chapter 6: Command Line Console Management 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use this command to set the cost of a path associated with a bridge-group. Use the no parameter with this command to restore the default cost of a path associated with a bridge-group. 3.
Chapter 6: Command Line Console Management switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use spanning-tree link-type command to set the link type of a port to enable or disable rapid transition. Use the no spanning-tree link-type command to set a port to its default state and to disable rapid transition. 3. Command Syntax: (no) spanning-tree link-type LINKTYPE LINKTYPE The link type to be assigned to the port. point-to-point Enable rapid transition. shared Disable rapid transition. 4.
Chapter 6: Command Line Console Management Use the no spanning-tree autoedge command to disable this feature. 3. Command Syntax: (no) spanning-tree autoedge 4. Example: The following example enables the spanning-tree autoedge of the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#spanning-tree autoedge switch_a(config-if)# Edgeport: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1.
Chapter 6: Command Line Console Management switch_a(config-if)# MSTP Properties Region Name: 1. Command Mode: MST Configuration mode Logon to Configure Mode (Configure Terminal Mode). Then logon to MST Configuration mode. The switch_a(config-mst)# prompt will show on the screen. switch_a(config)#spanning-tree mst configuration switch_a(config-mst)# 2. Usage: Use this command to create an MST region and specify a name to it. MST bridges of a region form different spanning trees for different VLANs.
Chapter 6: Command Line Console Management switch_a(config)#spanning-tree mst configuration switch_a(config-mst)# 2. Usage: Use this command to specify the number for configuration information. The default value of revision number is 0. 3. Command Syntax: bridge GROUP revision REVISION_NUM GROUP <1-1> Specify the bridge-group ID. REVISION_NUM <0-255> Revision number. 4.
Chapter 6: Command Line Console Management HOP_COUNT Maximum hops the BPDU will be valid for. 4. Example: The following example specifies the maximum allowed hops (25) for BPDU in bridge GROUP (1): switch_a(config)#bridge 1 max-hops 25 switch_a(config)# MSTP Instance Setting Bridge Instance VLAN: 1. Command Mode: MST Configuration mode Logon to Configure Mode (Configure Terminal Mode). Then logon to MST Configuration mode. The switch_a(config-mst)# prompt will show on the screen.
Chapter 6: Command Line Console Management switch_a(config)#bridge 1 protocol mstp switch_a(config)#spanning-tree mst configuration switch_a(config-mst)#bridge 1 instance 1 vlan 10, 20 switch_a(config-mst)# Bridge Instance Priority: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to set the bridge priority for an MST instance to the value specified.
Chapter 6: Command Line Console Management Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use this command to assign a Multiple Spanning Tree instance to a port. Use the no parameter with this command to remove the instance. 3.
Chapter 6: Command Line Console Management 2. Usage: Use this command to set the port priority for a bridge group. The Multiple Spanning Tree Protocol uses port priority as a tiebreaker to determine which port should forward frames for a particular instance on a LAN, or which port should be the root port for an instance. A lower value implies a better priority. In the case of the same priority, the interface index will serve as the tiebreaker, with the lower-numbered interface being preferred over others.
Chapter 6: Command Line Console Management 2. Usage: Use this command to set the cost of a path associated with an interface. Use the no parameter with this command to restore the default cost value of the path. A lower path-cost indicates a greater likelihood of the specific interface becoming a root. 3. Command Syntax: bridge GROUP instance INSTANCE_ID path-cost PATH_COST GROUP <1-1> Specify the bridge-group ID. INSTANCE_ID <1-15> Specify the instance ID.
Chapter 6: Command Line Console Management BRIDGE-FORWARD Puts all ports of the specified bridge into the forwarding state. 4. Example: The following example enables Ring state in bridge GROUP (1): switch_a(config)#bridge 1 protocol ring switch_a(config)# Set ring port: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to set Ring port 1 and Ring port 2. 3.
Chapter 6: Command Line Console Management 2. Usage: Use vlan database command to enter the VLAN configuration mode. 3. Command Syntax: vlan database 4. Example: The following example changes to VLAN configuration mode from Configure mode: switch_a(config)#vlan database switch_a(config-vlan)# Add VLAN/Delete VLAN: 1. Command Mode: VLAN Configure mode Logon to Configure Mode (Configure Terminal Mode). Logon to VLAN Configure Mode. The switch_a(config-vlan)# prompt will show on the screen.
Chapter 6: Command Line Console Management 4. Example: The following example enables the vlan VLANID (2) and name VLAN_NAME (vlan2) of bridge GROUP (1): switch_a(config-vlan)#vlan 2 bridge 1 name vlan2 state enable switch_a(config-vlan)# 802.1Q Port Setting Switchport mode access: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen.
Chapter 6: Command Line Console Management 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use switchport mode hybrid command to set the switching characteristics of the Layer-2 interface as hybrid, and classify both tagged and untagged frames.
Chapter 6: Command Line Console Management The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use switchport mode trunk command to set the switching characteristics of the Layer-2 interface as trunk, and specify only tagged frames. Use the no switchport trunk command to reset the mode of the Layer-2 interface to access (default). 3. Command Syntax: switchport mode trunk no switchport trunk 4.
Chapter 6: Command Line Console Management 3. Command Syntax: switchport hybrid allowed vlan all switchport hybrid allowed vlan none switchport hybrid allowed vlan add VLANID egress-tagged enable/disable switchport hybrid allowed vlan remove VLANID no switchport hybrid vlan all Allow all VLANs to transmit and receive through the Layer-2 interface. none Allow no VLANs to transmit and receive through the Layer-2 interface. add Add a VLAN to the member set. remove Remove a VLAN from the member set.
Chapter 6: Command Line Console Management The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use this command to set the switching characteristics of the Layer-2 interface to trunk. The all parameter indicates that any VLAN ID is part of its port’s member set. The none parameter indicates that no VLAN ID is configured on this port. The add and remove parameters will add and remove VLAN IDs to/from the port’s member set.
Chapter 6: Command Line Console Management 4. Example: The following example specifies to add the interface fe1 (port 1) to VLANID (2): switch_a(config)#interface fe1 switch_a(config-if)#switchport trunk allowed vlan add 2 switch_a(config-if)# Port Based VLAN Switchport portbase add/remove vlan: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen.
Chapter 6: Command Line Console Management 6.8 QoS Global Configuration, 802.1p Priority, DSCP Global Configuration QoS: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use mls qos enable command to globally enable QoS. Use the no mls qos command to globally disable QoS. 3. Command Syntax: mls qos enable (no) mls qos 4.
Chapter 6: Command Line Console Management cos Class of Service. dscp Differentiated Service Code Point. 4. Example: The following example turns on QoS trust CoS on the Hardened Ethernet Extender Switch: switch_a(config)#mls qos trust cos switch_a(config)# Strict Priority: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use priority-queue out command to enable the egress expedite queue.
Chapter 6: Command Line Console Management 2. Usage: Use wrr-queue bandwidth command to specify the bandwidth ratios of the transmit queues. 3. Command Syntax: wrr-queue bandwidth WRR_WTS WRR_WTS Weighted Round Robin (WRR) weights for the 4 queues (4 values separated by spaces). Range is 1–55. 4. Example: The following example specifies the bandwidth ratios of the transmit queues on the Hardened Ethernet Extender Switch: switch_a(config)#wrr-queue bandwidth 1 2 4 8 switch_a(config)# 802.1p Priority 1.
Chapter 6: Command Line Console Management 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use mls qos map dscp-queue command to map the DSCP values to a queue. 3. Command Syntax: mls qos map dscp-queue DSCP_VALUE to QUEUE_ID DSCP_VALUE DSCP values. Up to 8 values (separated by spaces). Range is 0-63. QUEUE_ID Queue ID. Range is 0-3. 4.
Chapter 6: Command Line Console Management 4. Example: The following example enables SNMP to the Hardened Ethernet Extender Switch: switch_a(config)#snmp-server enable switch_a(config)# Description: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use snmp-server description command to specify and no snmp-server description command to remove description for SNMP. 3.
Chapter 6: Command Line Console Management 3. Command Syntax: snmp-server location LOCATION no snmp-server location LOCATION The location for SNMP. 4. Example: The following example specifies location (location) for SNMP: switch_a(config)#snmp-server location location switch_a(config)# Contact: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2.
Chapter 6: Command Line Console Management prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to specify trap community name for SNMP. Use the no parameter with this command to remove trap community name for SNMP. 3. Command Syntax: snmp-server trap-community <1-5> NAME no snmp-server trap-community <1-5> <1-5> The trap community 1-5. NAME The trap community name for SNMP. 4.
Chapter 6: Command Line Console Management IP-ADDRESS The trap host IP address for SNMP. A.B.C.D specifies the IP address. 4. Example: The following example specifies trap host 1 IP address (192.168.1.20) for SNMP: switch_a(config)#snmp-server trap-ipaddress 1 192.168.1.20 switch_a(config)# Link Down Trap: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2.
Chapter 6: Command Line Console Management Use the no snmp-server trap-type enable linkUp command to disable link up trap for SNMP. 3. Command Syntax: (no) snmp-server trap-type enable linkUp 4. Example: The following example enables link up trap for SNMP: switch_a(config)#snmp-server trap-type enable linkUp switch_a(config)# SNMP v1/v2c Get Community Name: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen.
Chapter 6: Command Line Console Management 2. Usage: Use snmp-server community set command to specify and no snmp-server community set command to remove set community name for SNMP. 3. Command Syntax: snmp-server community set NAME no snmp-server community set NAME The set community name for SNMP. 4. Example: The following example specifies set community name (name) for SNMP: switch_a(config)#snmp-server community set name switch_a(config)# SNMP v3 SNMPv3 No-Auth: 1.
Chapter 6: Command Line Console Management switch_a(config)# SNMPv3 Auth-MD5, SNMPv3 Auth-SHA: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Add a user using snmp v3 with read-only or read-write access mode and with MD5 or SHA authentication. Use the no form of the command to delete this user. 3.
Chapter 6: Command Line Console Management 2. Usage: Add a user using snmp v3 with read-only or read-write access mode, MD5 or SHA authentication, and privacy. Use the no form of the command to delete this user. 3. Command Syntax: (no) snmp-server v3-user USERNAME (ro｜rw) priv auth (md5｜sha) AUTH_ PASSWORD des PRIV_PASS_PHRASE USERNAME Specify a user name.
Chapter 6: Command Line Console Management Use no dot1x system-auth-ctrl command to globally disable authentication. 3. Command Syntax: (no) dot1x system-auth-ctrl 4. Example: The following example globally enables authentication: switch_a(config)#dot1x system-auth-ctrl switch_a(config)# Radius Server IP: Radius Server Port: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2.
Chapter 6: Command Line Console Management switch_a(config)# Secret Key: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to set the shared secret key between a Radius server and a client. 3. Command Syntax: (no) radius-server host IP-ADDRESS key KEY IP-ADDRESS A.B.C.D specifies the IP address of the radius server host.
Chapter 6: Command Line Console Management radius-server timeout SEC no radius-server timeout SEC <1-1000> The number of seconds for a Hardened Ethernet Extender Switch to wait for a server host to reply before timing out. Enter a value in the range 1 to 1000. 4. Example: The following example specifies 20 seconds for the Hardened Ethernet Extender Switch to wait for a server host to reply before timing out: switch_a(config)#radius-server timeout 20 switch_a(config)# Retransmit: 1.
Chapter 6: Command Line Console Management Port Authentication Authentication State: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. fe1 means port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)# 2. Usage: Use dot1x reauthetication command to enable reauthentication on a port. Use no dot1x reauthetication command to disable reauthentication on a port. 3.
Chapter 6: Command Line Console Management 2. Usage: Use this command to force a port state. Use no dot1x port-control command to remove a port from the 802.1x management. 3. Command Syntax: dot1x port-control auto｜force-authorized｜force-unauthorized no dot1x port-control auto Specify to enable authentication on port. force-authorized Specify to force a port to always be in an authorized state. force-unauthorized Specify to force a port to always be in an unauthorized state. 4.
Chapter 6: Command Line Console Management 3. Command Syntax: dot1x timeout re-authperiod SECS no dot1x timeout re-authperiod SECS <1-4294967295> Specify the seconds between reauthorization attempts. The default time is 3600 seconds. 4. Example: The following example specifies to set the interval 25 seconds between reauthorization attempts: switch_a(config)#interface fe1 switch_a(config-if)#dot1x timeout re-authperiod 25 switch_a(config-if)# 6.
Chapter 6: Command Line Console Management 4. Example: The following example specifies to upgrade VDSL speed for Ethernet Extender port 1 (vdsl1): switch_a(config)#interface vdsl1 switch_a(config-if)#vdsl retrain switch_a(config-if)# VDSL Settings: Enable/Disable Asymmetric Mode: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. vdsl1 means Ethernet Extender port 1. The switch_a(config-if)# prompt will show on the screen.
Chapter 6: Command Line Console Management Asymmetric Mode Fixed Rate: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. vdsl1 means Ethernet Extender port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface vdsl1 switch_a(config-if)# 2. Usage: Use this command to set fixed rate bandwidth settings in the asymmetric mode for Ethernet Extender port.
Chapter 6: Command Line Console Management switch_a(config)#interface vdsl1 switch_a(config-if)#vdsl asym-fixedrate 59 switch_a(config-if)# Symmetric Mode Max. Speed: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. vdsl1 means Ethernet Extender port 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface vdsl1 switch_a(config-if)# 2. Usage: Use this command to set Max.
Chapter 6: Command Line Console Management 4. Example: The following example specifies to set Max. Speed settings (50) in the symmetric mode for Ethernet Extender port 1 (vdsl1): switch_a(config)#interface vdsl1 switch_a(config-if)#vdsl maxspeed 50 switch_a(config-if)# Symmetric Mode Fixed Rate: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. vdsl1 means Ethernet Extender port 1. The switch_a(config-if)# prompt will show on the screen.
Chapter 6: Command Line Console Management Table 6-3. VDSL fixed rates. Rate 1 Set fixed rate to 1 Mbps 3 Set fixed rate to 3 Mbps 5 Set fixed rate to 5 Mbps 10 Set fixed rate to 10 Mbpss 15 Set fixed rate to 15 Mbps 20 Set fixed rate to 20 Mbps 25 Set fixed rate to 25 Mbps 30 Set fixed rate to 30 Mbps 40 Set fixed rate to 40 Mbps 50 Set fixed rate to 50 Mbps 4.
Chapter 6: Command Line Console Management 4. Example: The following example shows Ethernet Extender port (vdsl1) status: switch_a>show vdsl status interface vdsl1 VDSL Counters 1. Command Mode: Exec mode Logon to Exec Mode (View Mode). The switch_a> prompt will show on the screen. switch_a> 2. Usage: Use this command to show Ethernet Extender port counters. 3. Command Syntax: show vdsl counter interface IFNAME IFNAME Interface name. 4.
Chapter 6: Command Line Console Management 2. Usage: Use set gvrp enable bridge command to enable (set) and set gvrp disable bridge command to disable (reset) GVRP globally for the bridge instance. This command does not enable/disable GVRP in all ports of the bridge. After enabling GVRP globally, use the set port gvrp enable command to enable GVRP on individual ports of the bridge. 3. Command Syntax: set gvrp enable bridge GROUP set gvrp disable bridge GROUP GROUP Bridge-group ID used for bridging. 4.
Chapter 6: Command Line Console Management 4. Example: The following example enables dynamic VLAN creation for bridge GROUP (1): switch_a(config)#set gvrp dynamic-vlan-creation enable bridge 1 switch_a(config)# Per port setting: GVRP: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2.
Chapter 6: Command Line Console Management The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to set the GVRP applicant state to normal or active. 3. Command Syntax: set gvrp applicant state active/normal IFNAME active Active state normal Normal state IFNAME Name of the interface. 4.
Chapter 6: Command Line Console Management set gvrp registration forbidden IF_NAME normal Specify dynamic GVRP multicast registration and deregistration on the port. fixed Specify the multicast groups currently registered on the Hardened Ethernet Extender Switch are applied to the port, but any subsequent registrations or deregistrations do not affect the port. Any registered multicast groups on the port are not deregistered based on the GARP timers.
Chapter 6: Command Line Console Management 4. Example: The following example enables IGMP snooping querier: switch_a(config)# ip igmp snooping querier switch_a(config)# IGMP mode: Passive: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use ip igmp snooping command to enable IGMP Snooping. This command is given in the Global Config mode.
Chapter 6: Command Line Console Management switch_a(config)#interface vlan1.1 switch_a(config-if)# 2. Usage: Use ip igmp version command to set the current IGMP protocol version on an interface. To return to the default version, use the no ip igmp version command. 3. Command Syntax: ip igmp version VERSION no ip igmp version VERSION IGMP protocol version number. 4. Example: The following example sets the IGMP protocol version 3 on vlan1.1: switch_a(config)#interface vlan1.
Chapter 6: Command Line Console Management 3. Command Syntax: (no) ip igmp snooping fast-leave 4. Example: The following example enables IGMP snooping fast-leave on vlan1.1: switch_a(config)#interface vlan1.1 switch_a(config-if)#ip igmp snooping fast-leave switch_a(config-if)# IGMP querier: Query-interval: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. vlan1.1 means vlan 1. The switch_a(config-if)# prompt will show on the screen.
Chapter 6: Command Line Console Management switch_a(config-if)#ip igmp query-interval 120 switch_a(config-if)# IGMP querier: Max-response-time: 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. vlan1.1 means vlan 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface vlan1.1 switch_a(config-if)# 2. Usage: Use ip igmp query-max-response-time command to configure the maximum response time advertised in IGMP queries.
Chapter 6: Command Line Console Management 1. Command Mode: Interface mode Logon to Configure Mode (Configure Terminal Mode). Then logon to Interface mode. vlan1.1 means vlan 1. The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface vlan1.1 switch_a(config-if)# 2. Usage: Use ip igmp snooping mrouter interface command to statically configure the specified VLAN constituent interface as a multicast router interface for IGMP Snooping in that VLAN.
Chapter 6: Command Line Console Management The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface vlan1.1 switch_a(config-if)# 2. Usage: Use ip igmp snooping report-suppression command to enable report suppression for IGMP versions 1 and 2. Use the no ip igmp snooping report-suppression command to disable report suppression. 3. Command Syntax: (no) ip igmp snooping report-suppression 4. Example: The following example enables report suppression for IGMPv2 reports on vlan1.
Chapter 6: Command Line Console Management 4. Example: The following example enables NTP for the Hardened Ethernet Extender Switch: switch_a(config)#ntp enable switch_a(config)# NTP Server: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to specify the IP address or Domain name of NTP server. 3. Command Syntax: ntp server IP-ADDRESS｜DOMAIN-NAME IP-ADDRESS A.B.C.
Chapter 6: Command Line Console Management 3. Command Syntax: ntp sync-time 4. Example: The following example synchronizes time with NTP server: switch_a(config)#ntp sync-time switch_a(config)# Time Zone: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2. Usage: Use this command to to set time zone. 3. Command Syntax: clock timezone TIMEZONE TIMEZONE Specifies the time zone.
Chapter 6: Command Line Console Management 3. Command Syntax: ntp polling-interval MINUTE MINUTE <1-10080> The polling interval. Enter a value in the range 1 to 10080 minutes. 4. Example: The following example specifies the polling interval 60 minutes: switch_a(config)#ntp polling interval 60 switch_a(config)# Daylight Saving Mode: 1. Command Mode: Configure mode Logon to Configure Mode (Configure Terminal Mode). The switch_a(config)# prompt will show on the screen. switch_a(config)# 2.
Chapter 6: Command Line Console Management TIMEZONE Specifies the daylight saving timezone. DAY <1-31> Specifies from 1 to 31. MONTH <1-12> Specifies from January to December. HOUR <0-23> Specifies from 0 to 23. MINUTE <0-59> Specifies from 0 to 59. OFFSET <1-1440> Specifies from 1 to 1440 minutes. no clock summer-time 4.
Appendix A: DB9 DCE Pin Assignment Appendix A. DB9 DCE Pin Assignment Table A-1. DB9 DCE connector pin assignments. LB308A Pin Number Name RS-232 Signal Name 1 DCD Data Carrier Detect 2 RXD Receive Data 3 TXD Transmit Data 4 — Not connected 5 GND Signal ground 6 — Not connected 7 CTS Clear to Send 8 — Not connected 724-746-5500 | blackbox.
Appendix B: Time Zones for Countries and Cities Appendix B. Time Zones for Countries and Cities Table B-1. Time zone codes.
Appendix B: Time Zones for Countries and Cities Table B-1 (continued). Time zone codes.
Appendix B: Time Zones for Countries and Cities Table B-1 (continued). Time zone codes.
Appendix B: Time Zones for Countries and Cities Table B-1 (continued). Time zone codes.
Appendix B: Time Zones for Countries and Cities Table B-1 (continued). Time zone codes.
Appendix B: Time Zones for Countries and Cities Table B-1 (continued). Time zone codes.
Appendix B: Time Zones for Countries and Cities Table B-1 (continued). Time zone codes.
NOTES LB308A 724-746-5500 | blackbox.
Black Box Tech Support: FREE! Live. 24/7. Tech support the way it should be. Great tech support is just 30 seconds away at 724-746-5500 or blackbox.com. About Black Box Black Box provides an extensive range of networking and infrastructure products. You’ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support available in 30 seconds or less. © Copyright 2011. Black Box Corporation.
