October 2009 FOPM-210 Deluxe Optical Power Meter with Memory Works with an optical laser source to test optical fiber cables for optical loss. BLACK BOX ® Works at six wavelengths: 850, 1300, 1310, 1490, 1550, and 1625 nm. Customer Support Information Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
FCC and NOM Statements FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
Deluxe Optical Power Meter with Memory 6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante. 7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante. 8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá lo descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a personal de servicio calificado. 9.
NOM Statement and Safety Information 18. Servicio por personal calificado deberá ser provisto cuando: A: El cable de poder o el contacto ha sido dañado; u B: Objectos han caído o líquido ha sido derramado dentro del aparato; o C: El aparato ha sido expuesto a la lluvia; o D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o E: El aparato ha sido tirado o su cubierta ha sido dañada.
Deluxe Optical Power Meter with Memory TRADEMARKS USED IN THIS MANUAL Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Excel is a registered trademark of Microsoft Corporation. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners. Page 4 724-746-5500 | blackbox.
Table of Contents 1. Specifications............................................................................................. 6 1.1 Optical Specifications........................................................................... 6 1.2 General Specifications......................................................................... 6 2. Overview.................................................................................................... 7 2.1 Introduction.........................................
Deluxe Optical Power Meter with Memory 1. Specifications 1.1 Optical Specifications NOTE: V alid at 1550 nm, CW. 23° C ±3° C, relative humidity less than or equal to 70% with FC connector. Table 1-1.
Chapter 2: Overview 2. Overview 2.1 Introduction Use the Deluxe Optical Power Meter with Memory (FOPM-210) with an optical laser source (FOLS-SM-200 or FOLS-MM-200) to identify optical fiber strands, measure optical attenuation, verify continuity, and test optical transmission quality in laboratories, LANs, WANs, telecommunications networks, and other longdistance optical applications. The FOPM-210 has a memory capacity of 1000 data items and supports data transfers via a USB port and the included software.
Deluxe Optical Power Meter with Memory 3. Operation 3.1 Battery Indicator A battery indicator on the screen shows the remaining charge. See Figures 3-1 and 3-2. Table 3-1 describes the LED status. Figure 3-1. Battery indicator full. Figure 3-2. Battery indicator empty. Table 3-1. Battery indicator status.
Chapter 3: Operation 3.2 AC Operation If you will use the power meter at one location, for example, in a laboratory or test department, you can use the AC adapter to power it instead of batteries. Plug the AC adapter’s output cable into the DC input jack on the bottom of the power meter. When the AC adapter is plugged in, the AC indicator on the LCD will be displayed. See Figure 3-3. Figure 3-3. AC adapter indicator. NOTES: Power is supplied by the AC adapter even if a battery is installed.
Deluxe Optical Power Meter with Memory 4. Using the Deluxe Optical Power Meter with Memory 4.1 Display and Controls 2 3 6 1 4 5 Figure 4-1. Keypad functions: Number 1 through 6. 4.1.1 Keypad Use the keypad to access a wide range of power meter functions. See Table 4-1. Table 4-1. Keypad functions. Number Key Function 1 Switches tester on/off. Press and hold for more than two seconds while turning on to disable the auto-off feature. 2 Press to set the wavelength.
Chapter 4: Using the Deluxe Optical Power Meter with Memory Table 4-1 (continued). Keypad functions. Number Key Function 6 Press to switch backlighting on/off. 4.1.2 Connectors FC/PC connector (FC/ST, FC/SC interchangeable connectors optional) USB connector External power/ Recharging LED DC input jack Battery fully charged LED Figure 4-2. Deluxe Optical Power Meter with Memory, bottom view. NOTE: The recharge LED lights when recharging batteries. The AC adapter LED lights when recharging finishes.
Deluxe Optical Power Meter with Memory 4.1.3 LCD Wavelength Reference Frequency AC adapter Battery indicator Measurement unit AutoPower Auto-off wavelength recognition Figure 4-3. LCD. . 4.2 Turning the Optical Power Meter On and Off 1. Press the key briefly. The power meter powers on, and backlighting switches on. I f the unit doesn’t power on, check the battery charge and make sure the battery is connected properly. If the battery fails, contact Black Box Technical Support at 724-746-5500.
Chapter 4: Using the Deluxe Optical Power Meter with Memory 3. Turn on/off the auto-off function. The power meter powers off automatically if you do not press a key within 10 minutes. Press the key for about two seconds to deactivate the auto-off function and the indicator will disappear on the LCD. The power meter powers off if the battery capacity is too low to support operation. 4.3 Setting the Wavelength Press the key repeatedly until the desired wavelength displays.
Deluxe Optical Power Meter with Memory 4.5 Setting and Checking the Reference Level 1. Setting the reference level: Press and hold the key for more than two seconds to store the presently measured value as the new reference level for the current wavelength. Once you set the new reference level, the LCD displays 0.00 dB, the buzzer sounds, and the power meter switches to dB measurement mode. 2. Checking the reference level: Press the key to display the stored reference level for the current wavelength.
Chapter 4: Using the Deluxe Optical Power Meter with Memory 4.8 Measured Power Value Overflow If the measured power value is higher than the highest value of the measuring range, the LCD screen displays HI. Figure 4-9. Power value high. If the measured power value is lower than the lowest value of the measuring range, the LCD screen displays LO. Figure 4-10. Power value low. 4.9 Storing the Current Test Value Press and hold the key for more than two seconds.
Deluxe Optical Power Meter with Memory 4.11 Connecting to the Optical Laser Source When connected to the dual-wavelength laser source (FOLS-SM-200 or FOLSMM-200), the Optical Power Meter (FOPM-210) accurately measures loss at distances up to 250 kilometers at 1550 nm. On-the-spot measurement will differ with the working wavelength, fiber attenuation, and the testing environment. Page 16 724-746-5500 | blackbox.
Chapter 5: Maintenance 5. Maintenance Disconnect the AC adapter/charger and replace the protective dust cap once you finish using it. Clean the connector and the instrument when they get dirty from use. We recommend using optical cleaning pads and anhydrous alcohol. Be careful not to get liquid inside the instrument. For measurement accuracy, calibrate the power meter once a year. 724-746-5500 | blackbox.
Deluxe Optical Power Meter with Memory Appendix. Troubleshooting A.1 Calling Black Box If you determine that your Deluxe Optical Power Meter with Memory is malfunctioning, do not attempt to alter or repair the unit. It contains no user-serviceable parts. Contact Black Box Technical Support at 724-746-5500. Before you do, make a record of the history of the problem.
Warranty Three-Year Limited Warranty Products are warranted against defective components and workmanship for three years from the date of delivery to the original customer. Any product found to be defective within the warranty period can be returned to an authorized service center for repair, replacement, and calibration. Exclusions The warranty on your equipment does not apply to defects resulting from unauthorized repair or modification, misuse, negligence, or accident. 724-746-5500 | blackbox.
NOTES Page 20 724-746-5500 | blackbox.
NOTES 724-746-5500 | blackbox.
Black Box Tech Support: FREE! Live. 24/7. Tech support the way it should be. Great tech support is just 20 seconds away at 724-746-5500 or blackbox.com. About Black Box Black Box Network Services is your source for more than 118,000 networking and infrastructure products. You’ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support available in 20 seconds or less. © Copyright 2009.