ORDER NO. CRT4632 DEH-2350UB/XNES CD RDS RECEIVER DEH-2350UB /XNES DEH-2350UBG DEH-2350UBSW DEH-2350UB DEH-2350UB /XNES /XNES /XSES /XNES1 This service manual should be used together with the following manual(s): Model No. CX-3269 Order No. CRT4488 Mech. Module S11.1STD-DOUT Remarks CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly For details, refer to "Important Check Points for Good Servicing".
1 2 3 4 SAFETY INFORMATION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
5 6 7 8 CAUTION Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacture. Discord used batteries according to the manufacture's instructions.
1 2 3 4 [Important Check Points for Good Servicing] A In this manual, procedures that must be performed during repairs are marked with the below symbol. Please be sure to confirm and follow these procedures. 1. Product safety Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual. 1 Use specified parts for repair. Use genuine parts.
6 7 8 CONTENTS SAFETY INFORMATION .....................................................................................................................................2 1. SERVICE PRECAUTIONS................................................................................................................................6 1.1 SERVICE PRECAUTIONS .........................................................................................................................6 1.2 NOTES ON SOLDERING ...............
1 2 3 4 1. SERVICE PRECAUTIONS 1.1 SERVICE PRECAUTIONS A 1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual. 2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during power-on mode may damage the ICs inside the unit. 3.
5 6 7 8 9. Capacitor Bond Lock Silicon Glue (GEM1017) Place the capacitor in the center of the silk print, and confirm it does not touch to the connector. Then, apply silicon glue. A NG OK B C D 1.2 NOTES ON SOLDERING For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering.
1 2 3 4 2. SPECIFICATIONS 2.1 SPECIFICATIONS A B C General USB Rated power source...............14.4 V DC (allowable voltage range: 12.0 V to 14.4 V DC) Grounding system...................Negative type Maximum current consumption .....................................................10.0 A Backup current .......................4.0 mA or less Dimensions (W × H × D): DIN Chassis .....................178 mm × 50 mm × 165 mm Nose ...........................188 mm × 58 mm × 17 mm D Chassis ..............
5 6 7 8 2.3 PANEL FACILITIES A Head unit 12 3 4 5 7 8 9 1 6 a b P art S (SRC/OFF) (Back/display/ scroll) 2 (eject) 9 3 (list) a FUNCTION Press to select functions. Press and hold to recall the initial setting menu when the sources are off. k LIST/ ENTER Press to display the disc title, track title, folder, or file list depending on the source. While in the operating menu, press to control functions. c d P art 8 j B Display indication /DISP OFF 4 MULTI-CONTROL (M.C.
1 2 3 4 2.4 CONNECTION DIAGRAM A This unit 3 1 2 3 4 5 B 5 6 7 8 9 a b c d e 2 1 4 5 Power cord input Rear output or subwoofer output Antenna input Fuse (10 A) Wired remote input Hard-wired remote control adaptor can be connected (sold separately). f g Power cord h Perform these connections when not connecting a rear speaker lead to a subwoofer. 1 L 4 C F 5 R i j R 2 3 6 7 8 9 a b c d k l e f g h Perform these connections when using a subwoofer without the optional amplifier.
5 6 7 8 3. BASIC ITEMS FOR SERVICE 3.1 CHECK POINTS AFTER SERVICING A To keep the product quality after servicing, please confirm following check points. No. 1 4 Procedures Confirm whether the customer complain has been solved. If the customer complain occurs with the specific media, use it for the operation check. Play back a CD. (Track search) Check FM/AM tuner action. (Seek, Preset) Switch band to check both FM and AM. Check whether no disc is inside the product.
1 2 3 4 3.2 PCB LOCATIONS A C CD Core Unit (S11.1STD-DOUT) B A Tuner Amp Unit C B Keyboard Unit A:DEH-2350UB/XNES B:DEH-2350UBG/XNES D C:DEH-2350UBSW/XNES D:DEH-2350UB/XSES E:DEH-2350UB/XNES1 Unit Number : CWN5489 (A, B, D, E) : CWN5479 (C) E Unit Name : Tuner Amp Unit Unit Number : Unit Name : Keyboard Unit Unit Number : CWX3985 Unit Name : CD Core Unit (S11.
5 6 7 8 3.3 JIGS LIST - Jigs List Name 16P FFC Test Disc L.P.F. A Jig No. GGD1310 TCD-782 Remarks Tuner Amp Unit - CD Core Unit Checking the grating Checking the grating (Two pieces) Grease No. GEM1024 GEM1038 GEM1043 GEM1045 GEM1017 Remarks CD Mechanism Module CD Mechanism Module CD Mechanism Module CD Mechanism Module Capacitor Bond Lock - Grease List Name Grease Grease Grease Grease Silicon Glue B 3.
1 2 3 4 4. BLOCK DIAGRAM 4.
5 6 7 8 A JA251 PL 3 PRE OUT Q251 RCAG TUNL 2 CD_Lch 1 P251 ELECTRONIC VOLUME/ SOURCE SELECTOR IC201 PML022A 1 POUT_L 6 IN2_L IN1_L B JA901 FUSE 10 A AUX_Lch 4 B.UP IN4+_L FRONT_L VST VCK VDT 26 15 30 14 31 13 18 STB REAR_L 7 11 8 12 FL+ FLIn RLIn CLK FL- 7 FL- 5 RL+ 3 RL- RL+ AMP IC301 PAL007E DATA 17 B.UP 15 FL+ 1 9 RL- 3 5 7 MUTE Q351 (1/2) 22 BREM B.
1 2 3 4 5. DIAGNOSIS 5.1 OPERATIONAL FLOWCHART A Power ON Vcc = 1.2 V Pin 5 PVcc = 3.3 V Pin 1 BSENS B Pin 141 BSENS = L ASENS Pin 143 ASENS = L C DSENS Pin 140 DSENS = L Starts communication with Grille microcomputer. D 300 ms SWVDD <- H Pin 128 300 ms In case of the above signal, the communication with Grille microcomputer may fail. If the time interval is not 300 msec, the oscillator may be defective. Source keys operative E Source ON SYSPW <- H Pin 7 F Completes power-on operation.
5 6 7 8 5.2 ERROR CODE LIST ERROR CODES A If a CD memory device is inoperable, or operation of such media is stopped by an error, the error mode is established and a cause of the error is displayed by an error code. Indication of error codes is intended to reduce the number of calls from customers and facilitate failure analysis and repair work in servicing.
1 2 3 4 USB storage device A Message Cause NO DEVICE Turn the plug When plug and and play on. play is off, no USB storage deConnect a compatible USB stovice is conrage device. nected. FRMT READ Sometimes there is a delay between the start of playback and when you start to hear any sound. NO AUDIO Action Transfer the audio files to the USB storage device and connect. The connected USB storage device has security enabled Follow the USB storage device instructions to disable the security.
5 6 7 8 5.3 CONNECTOR FUNCTION DESCRIPTION A B WIRED REAR REMOTE OUTPUT CONTROL ANTENNA 15 13 11 9 7 5 3 1 16 14 12 10 8 6 4 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 FL+ FR+ FLFRRL+ RR+ RLRR- NC NC NC NC ACC B.REM B.
1 2 3 4 6. SERVICE MODE 6.1 DISPLAY TEST MODE A The information such as the system microcomputer version is checked. [How to enter Test mode] Press “ 1 ” and “ 3 ” keys simultaneously to start resetting. [Operation key] Operation key Processing Remarks Enter display test mode (2) Switch to next test mode 1+3 B [Test items] Start display test mode (2). (Press “ 1 ” + “ 3 ” keys simultaneously to start resetting.
5 6 7 8 6.2 CD TEST MODE - Flow Chart Test Mode IN TRK Contents MIN Display [BAND] [2] RF AMP *1 Gain switching TRK MIN SEC Power On (T.Offset is adjusted) TRK MIN SEC 00 [BAND] TRK MIN 00 SEC [BAND] 91 91 SEC TRK MIN TRK MIN SEC 0X 0X 0X TRK MIN SEC [<] 00 00 00 or 99 99 99 [3] ?? ?? ?? [3] F,T,RF AGC*7 F.
1 2 3 4 7. DISASSEMBLY While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same. A - Removing the Panel Assy (Fig.1) 1 1 Remove the two hooks. 2 Remove the two hooks and then remove the Panel Assy. 1 2 2 Fig.1 Panel Assy B - Removing the CD Mechanism Module (Fig.2, 3, 4) 1 Remove the screw. 2 Remove the two screws. 1 2 2 Fig.2 C Heat sink side The CD Mechanism Module side is made a bottom. 3 3 Fig.
5 6 7 8 A - Removing the Tuner Amp Unit (Fig.5) 1 1 Remove the two screws. 2 Remove the two screws. 3 Straighten the tabs at two locations indicated and then remove the Tuner Amp Unit. 3 1 2 B 3 2 Fig.5 Tuner Amp Unit C - Attention of removing (Fig.6) Don't remove this screws excluding the dismantlement of the CD Mechanism Module. D Fig.
1 2 3 4 - Disassembling the Panel Part (Fig.7, 8) A 1. Remove the arm while bending the rib of the panel upward. B Fig.7 2. Press the upside hook and the bottom side hook of the button at the same time, and pull out the button. C Fig.8 - Assembling the Panel Part (Fig.9, 10, 11) 1. Attach the button from the front side of the panel. D E Fig.9 2. Attach the spring to the arm as shown in the figure. The bended tip of the spring is set to this side. F Hitch the spring to the groove. 24 Fig.
5 6 7 8 3. Fit the spring in the groove at the position shown in the figure. A 4. Fit the boss on the lower side of the arm in the lower hole of the panel, and then warp the rib on the panel in the direction shown in the figure and fit the boss of the arm in the panel. B Fig.
1 2 3 4 How to carry the mecha unit 1. Hold the designated points (shown with dashed lines) of the upper chassis and the front/rear bracket. 2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion. 3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx.
5 6 7 8 How to remove the PU unit 1. Create an empty-clamp state according to “How to create empty clamp state (motor drive)”. 2. Hook the feeding screw biasing spring to a tentative hooking portion (Fig 2b). Be careful not to get injured by the spring edge. 3. Hold the PU at the position A as shown in Fig 1. Slide the PU as far as possible toward the holder in the feeding screw so that a joint on the outer end of the feeding screw is loosened. 4.
1 2 3 4 8. EACH SETTING AND ADJUSTMENT 8.1 CD ADJUSTMENT A 1) Cautions on adjustments In this product the single voltage (3.3 V) is used for the regulator. The reference voltage is the REFO1 (1.65 V) instead of the GND. If you should mistakenly short the REFO1 with the GND during adjustment, accurate voltage will not be obtained, and the servo’s misoperation will apply excessive shock to the pickup. To avoid such problems: a.
5 6 7 8 8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT A Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below.
1 2 Grating waveform 3 4 Ech -> Xch 20 mV/div, AC Fch -> Ych 20 mV/div, AC A 0 degrees 30 degrees 45 degrees 60 degrees 75 degrees 90 degrees B C D E F 30 DEH-2350UB/XNES 1 2 3 4
5 6 7 8 8.3 PCL OUTPUT CONFIRMATION A - PCL output With the TESTIN (22 pin) status of IC601 to be “H”, it is shifted to PCL Output Test mode after reset started. Check that square wave of 600.0 kHz is output from PCL (8 Pin) of IC601. If clock signal is out of this range, this resonator (X602) must be changed for a new one.
1 2 3 4 9. EXPLODED VIEWS AND PARTS LIST NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual.
5 6 7 8 (1) PACKING SECTION PARTS LIST Mark No. * * Description Mark No. Part No. Description Part No.
1 2 3 4 3 4 9.
5 6 7 8 (1) EXTERIOR SECTION PARTS LIST Mark No. > Description Mark No. Part No. Description Part No.
1 2 3 4 9.
5 6 7 8 CD MECHANISM MODULE SECTION PARTS LIST Mark No. Description Mark No. Part No. Description Part No. 50 Damper CNW1198 51 Arm CNW1726 1 .....
1 2 3 4 10. SCHEMATIC DIAGRAM 10.1 TUNER AMP UNIT (GUIDE PAGE) Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". C 120 CDSRQ 121 CDSTBY 122 123 ML R605 124 NM 125 126 C602 0.
5 6 7 8 A A-b 13 PML022A 5 IN4-_L ROL 8 7 6 5 1 2 3 4 main sub CCG1205-A CCG1218-A CCG1192-A DCH1201-A CCG1201-A R201 1k C204 NM C213 CCG1201-A 10p/50 C203 10p/50 C215 10p/50 C202 C201 CCG1192-A (DCH1201-A) 0.22u/6.3 C211 C212 0.22u/6.3 NM RN4983 RN1910 A : DEH-2350UB/XNES B : DEH-2350UBG/XNES C : DEH-2350UBSW/XNES D : DEH-2350UB/XSES E : DEH-2350UB/XNES1 2.2u/10 10u/10 4.7u/10 B RT3T22M UMH3N,RT3N66M GND VST Q251 6 1 C1 E1 2 5 B1 B2 4 3 E2 C2 RN1910 R256 VDD3.3V B.
VCOM 9 OU TCK 820 R231 B.UP VDD3.3V SW5V NM L231 AGND 1800p/50 1800p/50 NM AGND VOUTR 8 C232 0.01u/16 TMS C238 C237 LPF C623 GND C624 0.1u/10 5.6k F% C626 R626 0.1u/10 0.1u/10 C625 MODEL RB751S-40 0.1u/10 C630 0.1u/10 70 69 0.
PVCC4 8.2 R810 8.2 R809 2.2k R811 NM 39 DPDT DPDT2 DEH-2350UB/XNES 8 A-b GND INA INB OUTY Vcc GND TC7SET08FUS1 3 2 1 IC801 ILM GND 4 5 NM LTC114EUB 3.3k R893 GND Q892 Q891 LSA1576UB(QRS) FLPILM 0.1u/10 C629 R636 47k R625 40 SWVDD NM L851 ROT1 ROT0 KYDT ILMCLR1 ILMCLR2 DM DP AUXG AUXR AUXL CSENS R623 0.1u/10 R624 47k 41 42 43 44 C628 0.1u/10 C627 0.1u/10 5.6k F% C626 R637 NM 1.
DEH-2350UB/XNES 4 KN401 RFGND 3 1 P401 * RFGND C446 3 2 1 NM C448 FM(30%): -15.0 dBs AM(30%): -15.0 dBs C417 IMSA-6802-01Y900 C402 * L551 L418 6 7 8 9 10 NC7 NC6 NC5 NC4 NC3 C413 NM L406 0.022u/16 R403 100 100 R559 R560 NC9 NC10 NC11 NC12 NC13 C424 * TDA7706 IC401 AGND NM L416 R421 0 L414 L412 NM L413 NM DGND R429 NM GND NM R417 SI SCK FLPILM ML CDWAIT CDSTBY CDSRQ CDRST CPPW C671 110 112 111 109 CD_SCL 0.1u/10 C602 0.
USB5V R C L501 CTH1475-A (CTH1420-A-TLB) GRILL 801 - 850 SWVDD5 851 - 870 ILMPW 871 - 890 FLPILM 891 - 900 PW CONNECT 901 - 910 IC REG 911 - 930 ASENS 931 - 940 TELIN 941 - 950 A.ANT 951 - 960 W.
1 2 3 F B DEH-2350UB/XNES 4 1/4W KST0 2 1 S1824 2 1 2 S1826 1 1 2 1 2 1 2 1 2 2 S1830 CENTER S1834 2 S1837 5 2 2 S1839 CLOCK 2 KST4 2.
6 7 SOURCE KDT3 KDT2 1826 CN1821 CKS6287-A R1902 3 R1901 2 NM 5V NM DGND AUX:+2.
1 2 3 4 10.3 CD CORE UNIT (S11.1STD-DOUT) CXX1942 PICKUP UNIT(P10.5)(SERVICE) V3R3 4.7u/6.3 (2125) 2.7 2.4 (1/10W) 2.4 C104 (1/10SR,1608) R101 R102 R103 E:P5+P10 F:P1+P6 * A R106 REFO NM FOM 0.1u/10 F FOP T TOP R229 83 470 84 C217 R216 85 56p/50 1.2k 86 10k R214 C215 71 72 73 EFM AD.Vdd ASY RFO EQ2 EQ1 RF2RFA.GND2 88 A.Vdd2 0.1u/10 F BD F 90 F T 91 E T 92 89 A B F E 93 REFO d C229 C223 94 FE95 68p/50 FE 0.
FD 6 C C232 SKIP /CDSRQ /WAIT ADENA TEMP VDSENS 10k R235 C S 10k R260 NM P R707 C16M /CDSRQ 81 LRCK RFO SCKO DOUT EQ1 PA7 87 CONT DSCSNS PE5756A 90 B 12SNS F HOME BCLK D R293 C284 DATA 0 NM LOEJ CLCONT 39 R264 38 1k CONT DSCSNS R245 100k R253 8SNS NM 36 R254 91 35 92 HOME EJSW 34 E LRCK 0 37 8SNS 33 * 31 IO.Vdd1 96 IO.GND1 ADCIN 97 TE- RESET TEO C.GND 99 C.Vdd TE2 00 0.01u/16 C210 VPP X.
1 2 3 4 10.4 WAVEFORMS - CD CORE UNIT A 1DSCSNS 28SNS 4LOEJ 3HOME 5 V/div 5 V/div 5 V/div 5 V/div Note : 1. The encircled numbers denote measuring points in the circuit diagram. 2. Reference voltage REFO1(1.65 V) 500 ms/div 1DSCSNS 5CLCONT 4LOEJ 6VD 5 V/div 5 V/div 5 V/div 10 V/div 500 ms/div 1DSCSNS 28SNS 4LOEJ 3HOME 5 V/div 5 V/div 5 V/div 5 V/div 12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation Ref.: GND Ref.: GND Ref.
5 fRFAGC cTE 9TIN 6 1 V/div 500 mV/div 500 mV/div 2 ms/div fRFAGC cTE 8CIN 7SIN 7 1 V/div 200 ms/div 1 V/div 500 mV/div 2 V/div 8 gLRCK hBCLK iDATA 2 V/div 2 V/div 2 V/div 32 Tracks Jump waveform (Zoom of 100 Track Jump waveform) Search operation(Outter to Inner) Digital Out waveform Ref.: REFO Ref.: REFO Ref.
1 2 3 4 11. PCB CONNECTION DIAGRAM 11.1 TUNER AMP UNIT 150 W.
5 6 7 8 A > P 251 (A,7,129) Fuse 3 A SIDE A CEK1286 IC301 20 5 9 13 E 1 15 18 17 C309 > R753 1 16 C752 D751 1 Q752 C754 C901 C318 B C751 C753 R934 D951 D901 1 P401 C451 CN701 C430 C455 R412 R556 R819 R873 C231 C809 D804 C922 E Q872 C916 C924 C914 C917 C920 R911 C919 10 C911 C918 C915 C923 5 1 IC912 E R871 R811 C871 R872 C805 R820 R802 R874 R816 D803 D805 D802 R815 L802 D801 R814 10 5 R801 R810 R809 1 D807 C807 S691 R807 D810 C820 C8
1 A A 2 3 4 TUNER AMP UNIT 1 B 1 C PCL TESTIN D E 1 1 1 F A 52 160 150 140 130 120 110 DEH-2350UB/XNES 1 2 3 4 100 90
5 6 7 8 A SIDE B 150 1 140 1 1 130 B 120 110 100 C 90 80 PCL 70 N D 60 50 40 E 1 30 20 1 10 1 F Y 100 90 80 70 60 50 40 30 20 10 X 0 A DEH-2350UB/XNES 5 6 7 8 53
1 2 30 40 D1874 3 50 D1858 S1839 70 80 1 S1836 90 S1837 2 C1862 D1861 100 3 S1838 25 LCD V1801 C1863 D1862 D1883 110 20 4 S1835 C1866 15 D1882 D1865 120 5 C1865 130 S1834 10 5 140 6 S1833 1 R1823 CN1901 AUX 150 1 USB CN1911 160 A 60 DOWN S1828 D1854 D1877 CLOCK 30 D1864 D1881 20 C1859 35 D1863 10 S1827 D1876 X D1871 S1843 C1867 D1913 RIGHT D1875 S1826 D1857 S1825 40 IC1802 2 Y DISP D1866 C1858 S1829 C1856 S1845 C1857 S1824
IC1801 45 50 10 15 X1801 55 R1805 D1802 D D1801 1 R1821 R1822 R1892 R1889 1 5 Q1851 R1893 R1890 R1864 R1898 50 R1854 R1801 5 60 R1872 R1803 R1804 1 R1806 70 R1874 R1852 40 30 R1824 R1825 R1826 10 R1851 R1885 R1884 R1856 R1894 R1875 20 R1858 R1891 R1888 R1899 C1802 1 80 R1897 L1801 5 90 R1853 L1911 1 15 CN1821 10 C 100 R1882 R1881 R1871 R1880 R1895 1 30 25 20 CN801 A 110 1 D1911 R1896 R1901 R1902 20 120 R1860 R1862 R1855 C1864 C1901 C1902
1 2 3 4 11.3 CD CORE UNIT (S11.1STD-DOUT) C CD CORE UNIT (S11.1STD-DOUT) SIDE A A PICKUP UNIT(P10.
5 7 8 CD CORE UNIT (S11.
1 2 3 4 12. ELECTRICAL PARTS LIST A B NOTE: Parts whose parts numbers are omitted are subject to being not supplied. The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
5 6 Circuit Symbol and No. L L L X X 671 802 901 401 601 X 602 > P251 P 401 CN701 CN801 JA251 JA401 JA901 JA961 > (A,109,51) Oscillator 12.
1 Circuit Symbol and No. A B 2 3 Part No.
5 6 Circuit Symbol and No. C 616 (A,100,64) 7 Part No.
1 2 Circuit Symbol and No. R 1899 (B,61,13) 3 Part No. A (B,149,33) 10 uF (B,98,24) CCG1192 CKSRYB105K10 C Unit Number : CWX3985 Unit Name R R R R R 308 701 702 706 708 (A,58,36) (B,37,21) (B,38,20) (B,43,11) (A,40,22) RS1/16SS183J RS1/16SS101J RS1/16SS101J RS1/16SS221J RS1/16SS0R0J R 709 R 722 (A,40,21) (B,37,22) RS1/16SS0R0J RS1/16SS0R0J CAPACITORS : CD Core Unit(S11.1STD-DOUT) MISCELLANEOUS B Part No. RS1/4SA271J CAPACITORS C 1801 C 1802 4 Circuit Symbol and No.
