MDU9705A-10BT August 2000 Compact mDSL Modem © Copyright 2000. Black Box Catalogue, Ltd. 464 Basingstoke Road, Reading, Berkshire RG2 0QN TECHNICAL: SALES: FAX: ADDRESS: WEB: (0118) 965 6000 (0118) 965 5100 (0118) 965 5001 464 Basingstoke Road, Reading, Berkshire RG2 0QN www.blackbox.co.
Compact mDSL Modem Compact mDSL Modem Table of Contents Section Page Radio and TV Interference.....................................................2 CE Notice...............................................................................2 General Information...............................................................3 Features Description PPP Operational Background..............................................4 Configuration .......................................................................
Compact mDSL Modem General Information Thank you for your purchase of this Black Box product. This product has been thoroughly inspected and tested and is warranted for One Year parts and labor.
Compact mDSL Modem Compact mDSL Modem Configuration Router Black Box MDU9705A-10BT There are two modes of operation for the Compact mDSL Modem: Plug-n-Play and self configuration. Both are described below. Ethernet LAN PEC Device w/ Serial I/F Plug-n-Play Figure 1. Cisco router with serial interface, configured as PPP Half Bridge. For example, the customer site is assigned the addresses 192.168.1.0/24 through 192.168.1.1/24. The address 192.168.1.
Compact mDSL Modem of the CO unit should be changed. This feature gives ISPs, LECs and PTTs the ability to provision bandwidth on an as needed basis to customers. The Plug and Play application will also work in an HTTP/SNMP managed system using the by deploying a SNMP Management Module agent card with mDSL Rack Cards installed in Black Box’s 2U Access Rack system.
Compact mDSL Modem Compact mDSL Modem Configuration DIP Switch Set “S2” Configuration DIP Switch Set “S3” The only setting for S2 is for Clocking Mode between the Compact mDSL Modems. All other switches are reserved for factory usage and must remain in the default configuration. Default settings are shown in the table below.
Compact mDSL Modem Off On Off On Off On Off On Off On Off On Off On Off On On Off On Off On Off On Off On Off On Off Off On On Off Off On On Off Off On On Off Off On On Off On On Off Off On On Off Off On On Off Off On Off Off Off Off On On On On Off Off Off Off On On On Off Off Off Off On On On On Off Off Off Off Off Off Off Off Off On On On On On On On On Off Off Off Off Off Off Off On On On On On On On On On On On On On Off Off Off Off Off Off Off Off Off Off Off Off Off Off Off On On On On On On On O
Compact mDSL Modem Compact mDSL Modem Connecting 10Base-T Ethernet Port to PC (DTE) Power Connection The 10Base-T interface is configured as DTE (Data Terminal Equipment). If the Compact mDSL Modem is to connect to another DTE device such as a 10Base-T network interface card, construct a 10Base-T crossover cable and connect the wires as shown in the diagram below. 10BaseT Port RJ-45 Pin No. 1 (TD+) 2 (TD-) 10Base-T DTE RJ-45 Pin No.
Compact mDSL Modem Compact mDSL Modem Operation CRC Detected LAN receive frame(s) too large Detected LAN receive frame(s) not octet aligned Detected LAN receive frame(s) with bad CRC 9 pulses = When the Compact mDSL Modem has been properly configured and installed, it should operate transparently. This sections describes power-up, LED status monitors, and the built-in loopback test modes.
Compact mDSL Modem Compact mDSL Modem Test Modes intended to be evaluated only by another Processor. If the units are transmitting data and the pattern generator is enabled on one end of the link, the far end will begin receiving unframed packets and assume that the line has gone down. During test modes, the pattern generator is forced to time out before it can cause the DSL link to go down. The Compact mDSL Modem offers a proprietary Remote Loopback test modes, plus a built-in V.
Compact mDSL Modem Compact mDSL Modem Loops and Patterns The following section describes the Remote Loopback/BER test modes. Remote Digital Framer When Remote Loop/511 or Remote Loop/511/E is enabled via the front panel switch, the Remote unit’s Restart Timer is set to one minute. This is because when the 511/511E generator is initiated on the local unit, the Remote framer begins seeing unframed packets.
Compact mDSL Modem Compact mDSL Modem Appendix A 10BASE-T mDSL SPECIFICATIONS Clocking Modes: DTE Rate: Diagnostics: LED Status: Configuration: Power: Compliance: Transmission Line: Line Coding: Line Rates (DSL line): Line Interface: mDSL Physical Internal or Receive Recovered All 64k increments from 64 to 2304 kbps V52 compliant (511/511E) pattern generator and detector with error injection mode and Remote Loopback control by a single front panel switch The following LEDs are displayed on the front pa
Compact mDSL Modem How To Contact your Local Black Box Italy: Black Box Italia S.P.A Tel: 0227400280 Fax: 0227400219 www.blackbox.it Australia: Black Box Catalog Australia PTY LTD Tel: 0398797100 Fax: 0398702955 Germany: Black Box Deutschland Tel: 0811/5541-0 Fax: 0811/5541-499 www.blackbox-deutschland.com Brazil: Black Box Do Brasil Tel: (011) 5515-4000 Fax: (011) 5515-4002 www.blackbox.com.br Switzerland: Datacom Black Box Services AG Tel: 0554517070 Fax: 0554517075 www.black-box.
