QCE12U QCE24U QCE42U QCE-CEB QCE-GK QCE-DF-12U QCE-DF-24U QCE-DF-42U QCE-SPFP-1U QCE-SPFP-2U codes QCE-SPFP-3U codes QCE-SPFP-5U codes QCE-VCM-24U March 2009 QCE-VCM-42U codes codes codes Product Group QuietCab Elite 12U, Title™24U, and 42U User Manual Reduce noise and improve productivity BLACK BOXdata in your office with QuietCab soundproof cabinets. ® Customer Support Information Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
Trademarks Used in this Manual Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc. UL is a registered trademark of Underwriters’ Laboratories. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners. Page 2 724-746-5500 | blackbox.
FCC and IC RFI Statements and NOM Statement FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
NOM Statement 4. Todas las instrucciones de operación y uso deben ser seguidas. 5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc. 6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante. 7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante. 8.
NOM Statement 17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación. 18.
Table of Contents Table of Contents 1. Specifications...............................................................................................7 2. Overview......................................................................................................8 2.1 Introduction.......................................................................................8 2.2 Features.............................................................................................8 2.3 What’s Included.............
Chapter 1: Specifications 1. Specifications Attenuation — Up to 28.5 dB Cable Knockout Size — Top panel: (3) 3"x 13" (7.62 x 33.02 cm); Bottom panel: (3) 3" x 13" (7.62 x 33.02 cm) Capacity — 1102.3 lb. (500 kg) Fans — (2) 740 CFM total Footprint, Cladding — 30.7"W x 47.6"D (78 x 121 cm) Footprint, Floor — 30.7"W x 43.3"D (78 x 110 cm) Heat Load (Maximum) — 7.2 kW Power Consumption (Maximum) — 1 Amp Rack Units — 12 RoHS — Yes Size — QCE12U: External: 28"H x 30.7"W x 47.63"D (71.12 x 77.97 x 120.
Chapter 2: Overview 2. Overview 2.1 Introduction The QuietCab Elite reduces equipment noise to a level below background noise in an average office. It attenuates sound by 28.5 dB—the most you can get today in a soundproof enclosure. Independently tested as the most effective quiet cabinet in the world, the QuietCab Elite features an innovative airflow design with 7.2 kW heat dissipation—the equivalent of 37 single processor servers and peripherals.
Chapter 3: Preparing the Cabinet for Installation 3. Preparing the Cabinet for Installation Follow these simple recommendations for best performance from your new enclosure. 3.1 Handling NOTE: For palletized cabinets, see the unpacking instruction sheet before attempting to remove the cabinet from the pallet. To achieve the level of acoustic performance and industrial needs of a high-quality 19” enclosure, the composition of cabinet parts means that the QuietCab Elite cabinets are very heavy.
Chapter 3: Preparing the Cabinet for Installation 3. To remove rear doors, disconnect the power supply, turn the cam lock with key supplied, then lift the swing handle and turn it clockwise. Hold the left-hand door in position while opening the right-hand door. NOTE: Open without disturbing the sound-proof seals. 4. Each door has a cooling fan connected to a fan-speed controller placed behind the side infills.
Chapter 3: Preparing the Cabinet for Installation CAUTION: Make sure that once fitted, the foam does not cover any of the equipment’s vents. Table 3-1. Quick fit soundproof blanking panels.
Chapter 3: Preparing the Cabinet for Installation Cables are usually run into the side cable apertures of a cabinet and straight onto cable trays fitted to the cabinet frame (see Figure 3-5). With the interconnecting server and equipment, cables are dressed to the side and rear. Most equipment fans expel hot waste air to the rear of the cabinet.. Disorganized cabling can inhibit airflow movement, so be careful when dressing cabling. We recommend that cables are dressed to the side rear infill panels.
Chapter 3: Preparing the Cabinet for Installation The cable entry box is reassembled in the hole exposed by removing the gland and soundproofing material. Assemble it from the inside of the cabinet so that the flange makes a seal on the cabinet’s soundproofing material showing rear center base assembled. Make sure foam is dressed around cables so that no air can escape. This will ensure that any airborne sound inside the cabinet is retained and attenuated within the enclosure.
Chapter 3: Preparing the Cabinet for Installation Two foam inserts are supplied as standard and should be fitted, regardless of cables being passed though, because this ensures the correct air path for cooling. Keep cable bundle flat where possible when passing through foam blocks. Figure 3-4. Cable entry box. Rear base shown. NOTE: Keep cables flat where possible.
Chapter 3: Preparing the Cabinet for Installation Figure 3-5. Cable tray. 724-746-5500 | blackbox.
Chapter 3: Preparing the Cabinet for Installation Table 3-2. Available cable trays. Rack Units Description Part Number 12U 5.9" (150 mm) wide *Contact Tech Support. 24U 5.9" (150 mm) wide *Contact Tech Support. 24U 5.9" (150 mm) wide *Contact Tech Support. 42U 5.9" (150 mm) wide *Contact Tech Support. 42U 5.9" (150 mm) wide *Contact Tech Support. *Contact Black Box Technical Support at 724-746-5500 or info@blackbox.com. These along with other accessories can be purchased from Black Box.
NOTES 724-746-5500 | blackbox.
NOTES Page 18 724-746-5500 | blackbox.
NOTES 724-746-5500 | blackbox.
Black Box Tech Support: FREE! Live. 24/7. Tech support the way it should be. Great tech support is just 30 seconds away at 724-746-5500 or blackbox.com. About Black Box Black Box provides an extensive range of networking and infrastructure products. You’ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support available in 30 seconds or less. © Copyright 2012. Black Box Corporation.