VSW-HDMI2X1-4K VSW-HDMI4X1-4K 2 x 1 or 4 x 1 HDMI Switch 4K Switch between two or four different HDMI sources BLACK BOX to a single display. ® Supports up to 4 K (UHD) resolutions (3840 x 2160). Automatically switches to a source when it becomes available. Customer Support Information Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
Trademarks Used in this Manual Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners. Page 2 724-746-5500 | blackbox.
FCC and IC RFI Statements/NOM Statement FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
NOM Statement 4. Todas las instrucciones de operación y uso deben ser seguidas. 5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc. 6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante. 7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante. 8.
NOM Statement 16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo. 17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación. 18.
Table of Contents Table of Contents 1. Specifications.................................................................................................. 7 2. Overview......................................................................................................... 9 2.1 Introduction........................................................................................... 9 2.2 Features................................................................................................. 9 2.
Chapter 1: Specifications 1.
Chapter 1: Specifications Specifications (continued) Indicators VSW-HDMI2X1-4K: (2) LEDS for input status; VSW-HDMI4X1-4K: (4) LEDs for input status NOTE: Only one input LED is lit at a time. Environmental Temperature Tolerance: Operating: 32 to 104° F (0 to 40° C); Storage: -4 to +140° F (-20 to +60° C); Relative Humidity: 80% Altitude: 10,000 ft. Power Input voltage: 100 to 240 VAC, 50 to 60 Hz, 45 watts, Input connector: IEC320 C14. Output voltage: 9 VDC, 1.5 A via a 2.
Chapter 2: Overview 2. Overview 2.1 Introduction The 2 x 1 or 4 x 1 HDMI Switch 4K enables users to quickly and easily share display devices (HDTV, Blu-ray player, HD-DVD, Xbox, Wii, PS3, satellite receiver, etc.) from your device inputs to one output device (monitor, projector, or TV). You can select the desired input source within the range of 16.4 feet (5 meters) via the remote control or push button located on the switch.
Chapter 2: Overview Advanced Autosensing • Select ports in Priority, Auto-sensing, and Switch modes. - I n Priority mode, the system automatically selects highest priority source to display (Priority order: Source-1 > Source-2 > ……). - In Auto-sensing mode, the system automatically selects the latest video source to display. - In Switch mode, the system selects the outputs to switch. • Switch outputs by pressing a button or setting priority.
Chapter 2: Overview 2.4 Hardware Description 1 2 Figure 2-1. 4 x 1 switch front panel. 3 4 5 6 7 Figure 2-2. 4 x 1 switch back panel. 9 8 Figure 2-3. 4 x 1 switch top panel. 724-746-5500 | blackbox.
Chapter 2: Overview Table 2-1. 2 x 1 and 4 x 1 switch components. Label in Fig.
Chapter 2: Overview Audio/Video EDID Setting Switch See #7 in Figure 2-2 and Table 2-1. Table 2-2. Audio/video EDID setting switch functions. Mode Video Audio 1 Auto Auto 2 Auto Inventory 3 Inventory Auto 4 Inventory Inventory NOTE: For more operation details, refer to Chapter 4, Operation. Advanced Autosensing Setting Switch See #3 in Figure 2-1 and Table 2-1. Table 2-3. Advanced autosensing setting switch.
Chapter 3: Installation 3. Installation WARNING: Before installation, power off all devices that will be connected to this system. Make sure that all devices you will connect are properly grounded. Place cables away from fluorescent lights, air conditioners, and machines that are likely to generate electrical noise. 3.1 Device Connection 1. U se a video cable (HDMI) to connect the display to the video output port on the unit. 2.
Chapter 3: Installation 3.2 Connection Pattern TV PC tower Stereo Remote Media play Controller Figure 3-1. Connecting the 4 x 1 HDMI Switch 4K. 724-746-5500 | blackbox.
Chapter 4: Operation 4. Operation 4.1 LED Indicators LEDs 1–4 Figure 4-1. Top and front panel of the switch. Table 4-1. LED Indicators LEDs 1–4 Switch/Auto/Priority/Modes Status The selected LED emits green and goes off 3 times per 2 seconds. The non-selected LED goes off. The input video signal isn't ready. The selected LED emits green and goes off once per 2 seconds. The input video signal is ready but cannot detect the monitor. The selected LED emits steady green.
Chapter 4: Operation 4.2 Push Button Control 4.2.1 A/V Source Selection Press the pushbutton (#11 in Figure 2-3) once to select the source in sequence (S1—>S2—>S3—>S4—>S1…). The monitor immediately shows the video source once selected. The corresponding LED lights when the source is selected. 4.2.2 EDID Setting NOTE: B efore starting, slide Audio/Video EDID Setting Switch (#7 in Figure 2-2) to position 2/3/4. Copy Monitor EDID (2 methods) Method 1 Step 1. Apply power to the unit. Step 2.
Chapter 4: Operation 4.2.3 EDID Emulation Slide the switch (#7 in Figure 2-2) to the desired position. Table 4-1. EDID emulation switch functions. Mode Video Audio 1 Auto (Va) Auto (Va) 2 Auto (Va) Inventory (Ai) 3 Inventory (Vi) Auto (Aa) 4 Inventory (Vi) Inventory (Ai) Va) Video Auto: Automatically use the EDID of the attached display (video algorithm). Aa) Audio Auto: Automatically use the EDID of the attached display (audio algorithm).
Chapter 4: Operation 4.2.5 Factory Default Setting To return all settings to factory state, press the BTN & EDID Copy button for 9 seconds and release right after 4 LEDs (L1–L4) flash green twice. BTN + EDID Copy (9 seconds)—>4 LEDs (L1–L4) flash green twice—>release 4.3 IR Remote Control A/V Source selection: Press 1/2/3/4: Select Source1/Source 2/Source/Source 4 724-746-5500 | blackbox.
Chapter 5: Serial Control (4-Port model only) 5. Serial Control (4-Port model only) The Video Switch’s built-in serial interface allows users to control the Switch through a PC, serial controller devices, or home theater system. The controller’s serial port should be configured as shown below. Baud Rate: 38400 bps Data Bits: 8 Parity: None Stop Bits: 1 Flow Control: None Figure 5-1. Hyperterminal screen. Page 20 724-746-5500 | blackbox.
NOTES 724-746-5500 | blackbox.
NOTES Page 22 724-746-5500 | blackbox.
NOTES 724-746-5500 | blackbox.
Chapter Black Box Tech Support: FREE! Live. 24/7. Tech support the way it should be. Great tech support is just 60 seconds away at 724-746-5500 or blackbox.com. About Black Box Black Box provides an extensive range of networking and infrastructure products. You’ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support available in 60 seconds or less. © Copyright 2014. Black Box Corporation.
