Operation Manual

8
ENGLISH
SURFACING/THICKNESSING ATTACHMENT ADE80 (TYPE 3)
Congratulations!
You have chosen an Elu product. Years of experience, thorough product
development and innovation make Elu one of the most reliable partners for
professional users.
Table of contents
Technical data en - 1
Manufacturer’s declaration en - 1
Safety instructions en - 1
Package contents en - 1
Description en - 2
Assembly and adjustment en - 2
Instructions for use en - 3
Maintenance en - 3
Guarantee en - 3
Technical data
Using MFF80/ Using HH40/
MFF81 HH40E
Max. surfacing width 90° mm 80 82
Max. surfacing width 45° mm 45 45
Max. thicknessing capacity mm 80 x 80 80 x 80
Max. planing depth mm 3.75 4.0
Thicknessing table mm 500 x 80 500 x 80
Surfacing fence length mm 350 350
Weight kg 3.7 3.7
Manufacturer’s Declaration
ADE80
Elu declares that the attachment mentioned above has been designed in
compliance with 89/392/EEC.
This attachment must not be put into service until it is established that the
Power Tool to be connected to this attachment is in compliance with
89/392/EEC (identified by the CE-marking on the Power Tool).
Director Engineering and Product Development
Horst Großmann
Elu International, Idstein, Germany
Safety instructions
Observe the safety regulations in the instruction manual of the Power
Tool to be connected to this attachment. Also observe any applicable
additional safety rules. Read the following safety instructions before
attempting to operate this product.
Keep these instructions in a safe place!
The attention of UK users is drawn to the “woodworking machines
regulations 1974” and any subsequent amendments.
General
• The attachment must be level and stable at all times.
• Keep the work top clear of foreign objects.
• Use the attachment with the Power Tools and accessories specified in
this manual only.
• Secure the Power Tool carefully.
• Work with closed hands.
• Make sure that your work area is properly lighted.
Surfacing/thicknessing
1 Dust extraction
As the planer produces dust and chips, the use of dust extraction
equipment is recommended. Proper dust extraction is especially
important if beech or oak dust is produced.
2 Wear safety goggles
Also use a face or dust mask to protect against dust or flying particles.
3 Protection devices
Only operate the Power Tool and attachment with all guards properly in
place.
4 Inspect workpiece
Remove any nails, staples and other metal parts.
5 Cutter blades
Use sharp and undamaged cutter blades only.
6 Damaged parts
Before operation, inspect the attachment, the Power Tool, the power
cable and the plug carefully for signs of damage. Have any damage
repaired by an Elu authorized repair agent before using the tool or
attachment.
7 Starting the planer
Before switching on, remove all adjustment spanners from the planer
and attachment.
8 Operating the planer and attachment
Do not overload the planer by feeding it at a too high rate. Always feed
the material against the rotational direction of the cutter block. Always
use a push stick, especially when working with smaller workpieces.
9 Stopping the planer
After switching off, the cutter block will continue to run for a few
seconds. Do not attempt to block it.
10 Maintain your attachment with care
Keep the attachment clean and in good condition for better and safer
performance. Follow the instructions for maintenance. Keep all controls
dry, clean and free from oil and grease.
11 Have your attachment repaired by an Elu authorized repair agent
This attachment is in accordance with the relevant safety regulations.
To avoid danger, it must only be repaired by qualified technicians.
Package contents
The package contains:
1 Surfacing/Thicknessing attachment
1 Support foot
1 Support bracket with foot
1 Support for handle
1 Switch edge for MFF80/MFF81
1 Switch strap for HH40/HH40E
1 Plastic bag containing:
5 screws
5 nuts
1 securing clip
2 fence securing knobs
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
en - 1