Powerful Solutions 3 TM 1 4 www.blackanddecker.
English 2 (Original instructions) 5
9 9 9 9 8 8 4 4 5 6 7 7 B A 13 11 5 10 11 13 5 10 11 13 12 10 5 C D 3
13 16 14 15 13 11 10 5 E 4 F
Intended use Your Black & Decker angle grinder has been designed for cutting metal and masonry using the appropriate type of cutting or grinding disc. This tool is intended for consumer use only. Safety instructions General power tool safety warnings @ Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. Service a.
Kickback and related warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory's rotation at the point of the binding.
Safety warnings specific for sanding operations u Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback. Safety warnings specific for polishing operations u Do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely. Tuck away or trim any loose attachment strings.
u u u u Place the spring washer (6) over the spindle and locate it on the shoulder (7). Place the guard (4) onto the tool as shown. Place the flange (8) over the spindle with the protruding pips towards the guard. Make sure that the holes in the flange align with the screw holes. Secure the flange with the screws (9). Make sure that the screws are fully tight and that the guard can be rotated. Removing u Use a screwdriver to remove the screws (9).
u u u u u Or run the battery down completely if it is integral and then switch off. Unplug the charger before cleaning it. Your charger does not require any maintenance apart from regular cleaning. Regularly clean the ventilation slots in your appliance/tool/ charger using a soft brush or dry cloth. Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner. Regularly open the chuck and tap it to remove any dust from the interior (when fitted).
EC declaration of conformity % MACHINERY DIRECTIVE AST15/KG725/KG900/KG915/KG925 Black & Decker declares that these products described under "technical data" are in compliance with: 98/37/EC (until Dec. 28, 2009), 2006/42/EC (from Dec. 29, 2009), EN 60745-1, EN 60745-2-3 For more information, please contact Black & Decker at the following address or refer to the back of the manual. _ To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent.
KG725 - KG900 - KG915 - KG925 - AST15 2 1 4 3 5 E14095 WWW.2helpU.com 30 - 09 - 09 TYP.
ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black & Decker in your country.
Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD 90554272 Tel. 03-8720 5100 Fax 03-9727 5940 Tel. +64 9 259 1133 Fax +64 9 259 1122 Tel.
