www.blackanddecker.co.
13 11 12 5 6 A B 5 14 8 D C 7 15 3 9 E 2 10 F
Intended use Your Black & Decker drill/screwdriver has been designed for screwdriving applications and for drilling in wood, metal and plastics. This tool is intended for consumer use only. Safety instructions General power tool safety warnings @ Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc.
o p Fire hazard! Avoid short-circuiting the contacts of a detached battery (e.g. when storing the battery in a toolbox). Do not attempt to charge damaged batteries. The charger is intended for indoor use only. Vibration The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN 60745 and may be used for comparing one tool with another.
Removing and refitting the chuck (fig. C) Open the chuck as far as possible. Remove the chuck retaining screw by turning it clockwise using a screwdriver. Tighten an Allen key (14) into the chuck and strike it with a hammer as shown. Remove the Allen key. Remove the chuck by turning it counterclockwise. To refit the chuck, screw it onto the spindle and secure it with the chuck retaining screw. Use Warning! Let the tool work at its own pace. Do not overload.
Use HSS drill bits when drilling in metal. Use masonry bits when drilling in soft masonry. Use a lubricant when drilling metals other than cast iron and brass. Make an indentation using a centre punch at the centre of the hole to be drilled in order to improve accuracy. Screwdriving Always use the correct type and size of screwdriver bit. If screws are difficult to tighten, try applying a small amount of washing liquid or soap as a lubricant.
Voltage No-load speed Max. torque Chuck capacity Max drilling capacity Steel Wood Weight VDC min-1 Nm mm KC12GT 12 700 8 10 mm 10 mm 25 kg 0,9 Battery Voltage Capacity Weight A9251 VDC 9.6 Ah 1.3 kg 0.365 A9252 12 1.0 0.5 Battery Voltage Capacity Weight A9272 VDC 9.6 Ah 1.5 kg 0.465 A9282 18 1.2 0.73 Charger Input voltage Approx. charging time KC14GT 14,4 750 12,5 10 10 25 1,01 A9262 14.4 1.2 0.
17 18 E15279 8 13 1 1 8 13 CD12C TY 2 CD12C TY 3 CD12C TY 6 CD14C TY 1 CD14C TY 2 CD14C TY 4 CD14C TY 6 CD14C TY 8 16 CD96C TY 1 CD12C TY 1 CD12C TY 5 CD14C TY 3 CD14C TY 7 CD18C TY 1 CD18C TY 3 CD18C TY 5 CD112C TY 1 14 3 www.2helpU.
Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD 90530269 Tel. 03-8720 5100 Fax 03-9727 5940 Tel. +64 9 259 1133 Fax +64 9 259 1122 Tel.
