2 3 4 15 5 14 13 6 12 11 10 9 8 7 CD601 CD602
English 2 (Original instructions) 5
B A 21 20 11 C 7 22 D 3
12 E 8 G 4 6 8 13 23 5 15 F
Intended use Your Black & Decker saw has been designed for sawing wood and wood products. This tool is intended for consumer use only. Safety instructions General power tool safety warnings @ Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. Service a.
Safety instructions for circular saws with outer or inner pendulum guards and with tow guard a. Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut. b.
Electrical safety # u This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard. Features 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
The height difference between the toothed rim and the lower end of the riving knife should be 2 - 3 mm. u Tighten the screw. Fitting and removing the parallel fence (fig. D) The parallel fence is used to saw in a straight line parellel to the edge of the workpiece. Fitting u Loosen the locking knob (21). u Insert the parallel fence (7) through the openings (22). u Slide the parallel fence into the desired position. u Tighten the locking knob. Removing u Loosen the locking knob (21).
Protecting the environment Z EC declaration of conformity Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. z Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.
Guarantee Black & Decker is confident of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.
TYP. CD601 - CD602 36 37 38 43 39 44 41 45 6 1 1-2-3 42 7 8 2 3 10 69 11 12 13 21 45 9 1 16 71 22 23 20 17 48 73 70 18 19 46 14 15 3 26 72 47 27 28 29 30 25 50 31 74 51 33 34 35 49 53 63 64 52 62 55 54 68 32 61 65 56 58 59 66 57 67 60 E13688 www.2helpU.
ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black & Decker in your country.
Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD 90580808 REV 0 Tel. 03-8720 5100 Fax 03-9727 5940 Tel. +64 9 259 1133 Fax +64 9 259 1122 Tel.
