User Manual

Size: 28.5" x 16" (72.39cm x 40.64cm)
How to Use
This product is for household use only.
GETTING STARTED
• Remove all packing material, any stickers, and the plastic band around the power plug.
• Remove and save literature.
• Please visit www.prodprotect.com/applica to register your warranty.
• Wash all removable parts as instructed in CARE AND CLEANING section.
• CAUTION: Handle blades and disks very carefully. They are very sharp.
• Select a level dry countertop where the appliance is to be used allowing air space on all sides to provide
proper ventilation for the motor.
ASSEMBLING THE PROCESSOR
Inserting / Removing Center Post
1. Turn the workbowl upside down.
2. To INSERT center post: Place post into smaller opening in bottom of workbowl and turn counterclockwise
until tabs lock in place. (B)
3. To REMOVE center post: grasp the white tabs and turn the center post clockwise until the lower tabs are
free. Lift the post out.
Locking Workbowl on Base
1. Attach center post to workbowl (see above). Place the workbowl on the base with handle turned to the
right of the locking mechanism (C) over the unlock symbol (
).
2. Hold handle and rotate workbowl clockwise toward the lock symbol (
) until it clicks firmly into place
(D). Be sure to lock the workbowl in place before attaching the blades and lid.
Locking Lid to Workbowl
1. Place lid over workbowl with the small latch to the right of the workbowl’s handle (E).
2. Hold feed chute of lid and rotate lid clockwise until lid locks into place.
Important: For your protection this appliance has an interlock system. The processor will not operate
unless the workbowl, cover and wide-mouth feed chute are properly locked in place.
3. Place the wide-mouth feed chute on top of the lid with the small tab to the right of the workbowl’s handle.
Turn clockwise until it clicks into position over the handle.
4. Insert the food pusher into the central tube of the wide-mouth feed chute. Turn clockwise to lock in place.
TRADITIONAL 10-CUP FOOD PROCESSOR
PROCESASOR DE ALIMENTOS TRADICIONAL DE 10 TAZAS
USING THE S BLADE
1. Attach center post to workbowl.
2. Lock workbowl onto base (D).
3. Hold S blade by center shaft and insert onto center post (F).
Caution: Blade attachments are very sharp. Use caution when handling and storing.
4. Place food in workbowl.
5. Place lid on workbowl and lock into place by rotating clockwise (E).
6. Attach the wide-mouth feed chute and insert food pusher.
Important: Never use your fingers to direct food through the chute.
7. Select your desired speed (PULSE, HIGH or LOW).
Note: Process foods for no more than a few seconds at a time. Pulsing produces more precise results and offers greater
control of end results.
Important: Be sure S- blade has completely stopped spinning before removing cover from processor.
8. Press the OFF/PULSE button and allow blades to stop revolving before removing lid. Twist lid toward (
) to remove.
9. Unplug appliance.
10. Unlock workbowl by turning it counterclockwise and lift off base.
Note: Remove bowl from appliance before removing blade to prevent food from leaking through the center opening of the bowl.
11. Carefully remove S blade.
USING THE SLICE/SHRED DISC
1. Attach center post to workbowl.
2. Lock workbowl into position (C and D).
3. Place disc stem onto center post in workbowl.
4. Carefully place slice/shred disc on stem with appropriate side up (depending on work to be done).
5. Place lid on workbowl and lock into place by rotating clockwise (E).
6. Place the wide-mouth feed chute and food pusher in place.
7. Fill feed chute with food. Select regular opening or wide-mouth, depending upon size of food to be processed. Position
food pusher over food (G or H).
8. Select PULSE, HIGH or LOW; press firmly on food pusher to guide food through processor, but do not force it.
Note: Heavy pressure on the pusher does not speed the work; use the pusher only as a guide. Let the processor do the
work.
9. When finished, press OFF/PULSE and wait for disc to stop rotating before removing lid. Twist lid toward (
)
to remove.
10. Unplug appliance.
11. Carefully remove the slice/shred disc. Unlock workbowl by turning it counterclockwise and lifting it off the base.
Care and Cleaning
This product contains no user serviceable parts. Refer service to qualified service personnel.
Note: Do not attempt to sharpen the cutting edges of the blades or discs. They are permanently sharpened at the factory
and will be ruined if sharpened.
CLEANING
Note: Before cleaning, be sure unit is turned off and cord is unplugged.
• Completely disassemble processor parts before washing.
• Rinse parts immediately after processing for easy cleanup.
• Wipe base and feet with a damp cloth and dry thoroughly. Do not immerse base in liquid.
• All removable parts can be washed by hand or in a dishwasher (top rack only).
• Do not use rough scouring pads or cleansers on any plastic or metal parts to clean.
• Do not allow blades or discs to soak in water for long periods of time.
• Remember to clean the internal shaft of the chopping blade; use a baby bottle brush to remove any clogged food particles.
Please Read and Save this Use and Care Book.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be followed, including the following:
• Read all instructions.
• To protect against risk of electrical shock, do not put food processor base, cord or plug in water or
other liquid.
• Close supervision is necessary when any appliance is used by or near children.
• Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.
• Avoid contacting blades and moving parts.
• Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions, or
has been dropped or damaged in any manner. Contact the consumer service number listed in this
manual. This appliance has important markings on the plug blade. The attachment plug or entire
cordset (if plug is molded onto cord) is not suitable for replacement. If damaged, the appliance
shall be replaced.
• The use of attachments not recommended by the appliance manufacturer may cause fire, electric
shock or injury.
• Do not use outdoors.
• Do not let cord hang over the edge of table or counter, or touch hot surfaces.
• Keep hands and utensils away from moving blades or discs while processing to reduce the risk
of severe injury to persons or damage to the food processor. A scraper may be used but must be
used only when the processor is not running.
• Blades are sharp. Handle carefully.
• To reduce the risk of injury, never place blade or disk on base without first putting workbowl
properly in place.
• Be certain the lid is securely locked in place before operating appliance.
• Never feed food by hand. Always use food pusher.
• Unit has a protection system. The unit will not operate unless the work bowl is securely locked
onto base and the lid is securely locked onto workbowl.
• Do not attempt to defeat the lid interlock mechanism.
• Do not use appliance for other than intended use.
• This product is designed for household use only.
• Do not open lid until blade or disk stops completely.
• The maximum rated wattage for this product was obtained with the multi-function S blade.
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
SAVE THESE INSTRUCTIONS.
This product is for household use only.
POLARIZED PLUG (120V Models Only)
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock,
this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any
way.
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a tamper-resistant screw to prevent removal of the outer cover.
To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-
serviceable parts inside. Repair should be done only by authorized service personnel.
ELECTRICAL CORD
The cord of this appliance was selected to reduce the possibility of tangling in or tripping over a longer
cord. If more length is needed, only extension cords having an electrical rating not less than the appliance.
When using an extension cord, do not let it drape over the working area or dangle where someone could
accidentally trip over it. Handle cord carefully for longer life; avoid jerking or straining it at outlet and
appliance connections.
Note: If the power cord is damaged, please call our Customer Service line listed in these instructions.
Product may vary slightly from what is illustrated.
A
CONTROLS
The controls are located on the front of the base. Press PULSE,
HIGH or LOW to select a function (see directions below).
OFF/PULSE
• Processor should be stored in OFF position and
unplugged when not in use.
• Use PULSE for short processing tasks. This lets you
control the size and uniformity of foods being chopped.
• The OFF/PULSE button must be pressed and held
for the appliance to operate in PULSE mode. When
released, the appliance stops.
• The motor of the processor will run as long as the OFF/
PULSE button is held down. Press the button and then
release to allow the blades to stop running and the food
to fall to the bottom of the workbowl.
• Pulsing gives better control when chopping, mincing,
mixing and blending foods. You can control the size of
the foods, from coarse to fine.
HIGH and LOW
• When either speed is selected, the processor runs
continuously until the OFF/PULSE button is pressed.
• Use LOW speed when slicing or shredding.
• Use HIGH speed for chopping, mixing, or blending foods.
E
F
D
C
B
OR
G
H
Model/Modelo: FP2500, FP2500B, FP2500S
Customer Care Line: 1-800-231-9786
For online customer service: www.prodprotect.com/applica
Línea de Atención del Cliente: 1-800-231-9786
Para servicio al cliente en línea: www.prodprotect.com/applica
† 1. Food pusher (Part # 07234DZ118 [white] / 07234EZB [black])
† 2. Wide-mouth feed chute (Part # 77788)
† 3. Lid (Part # 77786)
† 4. Reversible slice/shred disc (Part # 77792-1)
† 5. 10-cup workbowl
(Part # 77841(Only for Models FP2500B/FP2500S)
Part #77842 (Only for Model FP2500)
† 6. Multi-function S blade (Part # 77793)
7. Base
8. Touchpad Controls
9. Cord wrap (under base)
† 10. Non-skid suction feet (Part # 09183-1)
† 11. Disc stem (Part # 77789) (not shown)
Note: † indicates consumer replaceable/removable parts










Comercializado por:
Spectrum Brands de México, S.A de C.V
Autopista México Querétaro
No 3069-C Oficina 004
Colonia San Andrés Atenco, Tlalnepantla
Estado de México, C.P. 54040
Mexico.
Tel: (55) 5831 – 7070
Servicio y Reparación
Art. 123 No. 95
Col. Centro, C.P. 06050
Deleg. Cuauhtemoc
Servicio al Consumidor,
Venta de Refacciones y Accesorios
01 800 714 2503
Importado por / Imported by:
RAYOVAC ARGENTINA S.R.L.
Humboldt 2495 Piso# 3
(C1425FUG) C.A.B.A. Argentina.
C.U.I.T No. 30-70706168-1
Importado por / Imported by:
Spectrum Brands de México, S.A de C.V
Autopista México Querétaro
No 3069-C Oficina 004
Colonia San Andrés Atenco, Tlalnepantla
Estado de México, C.P. 54040
Mexico.
Tel: [phone]
Para atención de garantía marque:
01 [phone]
Importado por / Imported by:
Spectrum Brands
En Chile, Household Products Chile Ltda
Av. Del Valle 570, Ofic. 704
Ciudad Empresarial, Huechuraba
Santiago - Chile
Fono: (562) 2571 3700
Importado por / Imported by:
Spectrum Brands S.A.
Carrera 17 No.89-40
Bogotá, Colombia
Línea de atención al cliente:
018000510012
500 W 120 V ~ 60 Hz
Sello del Distribuidor:
Fecha de compra:
Modelo:
Código de fecha / Date Code / Le code de date:
Made and Printed in People’s Republic of China.
Fabricado e Impreso en la República Popular de China.
BLACK+DECKER and the BLACK+DECKER logo are trademarks of
The Black & Decker Corporation and are used under license. All rights reserved.
BLACK+DECKER y el logo tipo BLACK+DECKER son marcas registradas de
The Black & Decker Corporation y son utilizados bajo licencia. Todos los derechos reservados.
T22-5003188
15758-00
© 2016 The Black & Decker Corporation and Spectrum Brands, Inc., Middleton, WI 53562
NEED HELP?
TWO-YEAR LIMITED WARRANTY
(Applies only in the United States and Canada) For service, repair or any questions regarding your appliance, call the
appropriate 800 number on cover of this book. Please DO NOT return the product to the place of purchase. Also, please DO
NOT mail product back to manufacturer, nor bring it to a service center. You may also want to consult the website listed on
this manual.
What does it cover?
• Any defect in material or workmanship provided;
however, Spectrum Brands, Inc.’s liability will not
exceed the purchase price of product.
For how long?
• Two years from the date of original purchase with proof of
such purchase.
What will we do to help you?
• Provide you with a reasonably similar replacement
product that is either new or factory refurbished.
How do you get service?
• Save your receipt as proof of date of sale.
• Visit the online service website at
www.prodprotect.com/applica, or call toll-free
1-800-231-9786, for general warranty service.
• If you need parts or accessories, please call
1-800-738-0245.
What does your warranty not cover?
• Damage from commercial use
• Damage from misuse, abuse or neglect
• Products that have been modified in any way
• Products used or serviced outside the country of
purchase
• Glass parts and other accessory items that are packed
with the unit
• Shipping and handling costs associated with the
replacement of the unit
• Consequential or incidental damages (Please note,
however, that some states do not allow the exclusion or
limitation of consequential or incidental damages, so
this limitation may not apply to you.)
How does state law relate to this warranty?
• This warranty gives you specific legal rights. You may
also have other rights that vary from state to state or
province to province.
Por favor llame al número correspondiente que aparece en la lista a continuación para solicitar que se haga efectiva
la garantía y donde Ud. puede solicitar servicio, reparaciones o partes en el país donde el producto fué comprado.
Argentina
Atención al consumidor
0800 444 7296
Horario de atención:
Lunes a viernes de 9 a 13 hs
y de 14.30 a 17 hs.
email: [e-mail]
Humboldt 2495 piso 3
C.A.B.A. – Argentina
Chile
SERVICIO DE MAQUINAS Y
HERRAMIENTAS LTDA.
Portugal Nº 644
Santiago – Chile
Fonos: 02-6355208 / 02-6341169
Email: [e-mail]
Call center: 800-171-051
Colombia
Rayovac Varta S.A
Carrera 17 Número 89-40
Línea gratuita nacional
018000510012
Costa Rica
Aplicaciones Electromecanicas
Calle 22 y 24 en Avenida 3 BLV de la
torre Mercedes Benz
200 mts norte y 50 mts este
San José, Costa Rica
Tel. [phone]
Ecuador
Servicio Master
Dirección: Capitán Rafael
Ramos OE 1-85 y Galo plaza lasso.
Tel [phone]
El Salvador
Sedeblack
Calle San Antonio Abad, Colonia
Lisboa
No 2936
San Salvador, Depto. de San
Salvador
Tel. [phone]
Guatemala
Kinal
17 avenida 26-75, zona 11 Centro
comercial Novicentro,
Local 37 - Ciudad
Guatemala
Tel. [phone]
Honduras
Serviteca
San Pedro Sula, B Los Andes, 2 calle-
entre 11-12 Avenida
Honduras
Tel. [phone]
México
Articulo 123 # 95 Local 109 y 112
Col. Centro, Cuauhtemoc,
México, D. F.
Tel. [phone]
Nicaragua
LRM ELECTRONICA
Managua - Sinsa Altamira 1.5
kilómetros al norte
Nicaragua
Tel. [phone]
Panamá
Supermarcas
Centro comercial El dorado, Plaza
Dorado, Local 2.
Panama
Tel. [phone]
Perú
Servicio Central Fast Service
Av. Angamos Este 2431
San Borja, Lima Perú
Tel. [phone]
Puerto Rico
Buckeye Service
Jesús P. Piñero #1013
Puerto Nuevo, SJ PR 00920
Tel.: [phone]
Republica Dominicana
Prolongación Av. Rómulo
Betancourt
Zona Industrial de Herrera
Santo Domingo, República
Dominicana
Tel.: [phone]
Venezuela
Inversiones BDR CA
Av. Casanova C.C.
City Market Nivel Plaza Local 153
Diagonal Hotel Melia,
Caracas.
Tel. [phone]