HP96K HP12K(D) HP14K(D) HP122K(D) HP142K(D) 1
Copyright Black & Decker 2
4 5 3 2 6 7 1 8 11 10 9 15 12 14 13 A 3
10 18 9 16 17 B C 11 15 14 9 9 D 4 12 E 13
20 19 2 F G 5 I 3 21 22 H J 5
23 K 6 24
ENGLISH CORDLESS DRILL/SCREWDRIVER HP96K/ HP12K(D)/HP14K(D)/HP122K(D)/HP142K(D) CONGRATULATIONS! You have chosen a Black & Decker tool. Our aim is to provide quality tools at an affordable price. We hope that you will enjoy using this tool for many years.
ENGLISH Know your tool ◆ ◆ ◆ ◆ Warning! When using battery-powered tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, leaking batteries, personal injury and material damage. Read all of this manual carefully before operating the tool. Before operating the tool, make sure that you know how to switch the tool off in an emergency. Retain this manual for future reference. General 1.
ENGLISH 16. Store idle tools When not in use, tools, batteries and chargers should be stored in a dry, locked up or high place, out of reach of children. 17. Maintain tools with care Keep cutting tools sharp and clean for better and safer performance. Follow the instructions for maintenance and changing accessories. Keep handles and switches dry, clean and free from oil and grease. 18. Repairs This tool complies with relevant safety requirements.
ENGLISH HP96K/HP12K(D)/HP14K(D) Never attempt to replace the charger unit with a regular mains plug. HP122K(D)/HP142K(D) - Mains plug replacement (U.K. & Ireland only) ◆ ◆ ◆ ◆ ◆ ◆ ◆ Should your mains plug need replacing and you are competent to do this, proceed as instructed below. If you are in doubt, contact an authorised repair agent or a qualified electrician. Disconnect the plug from the supply and remove the fuse from the plug.
ENGLISH HP12KD/HP14KD/HP122KD/HP142KD Attaching the detector (fig. K) The tool provides a mounting location where the detector (23) is stored when not in use. ◆ Hang the unit to the holder (24) as shown. USE Let the tool work at its own pace. Do not overload. Charging the battery The battery needs to be charged before first use and whenever it fails to produce sufficient power on jobs that were easily done before.
ENGLISH ◆ For screwdriving, set the collar to the desired setting. If you do not yet know the appropriate setting, proceed as follows: ◆ Set the collar (3) to the lowest torque setting. ◆ Tighten the first screw. ◆ If the clutch ratchets before the desired result is achieved, increase the collar setting and continue tightening the screw. Repeat until you reach the correct setting. Use this setting for the remaining screws. HP122K(D)/HP142K(D) - Drilling in masonry (fig.
ENGLISH ◆ ◆ ◆ Regularly clean the ventilation slots in your tool and charger using a soft brush or dry cloth. Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner. Regularly open the chuck and tap it to remove any dust from the interior. PROTECTING THE ENVIRONMENT Tools Should you find one day that your tool needs replacement, or if it is of no further use to you, think of the protection of the environment.
ENGLISH ◆ Repairs have been attempted by persons other than authorised repair agents or Black & Decker service staff. To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual.
Australia DEWALT Industrial Power Tool Company 7 Clarice Road Box Hill, Victoria 3128 Tel. 03 9895 9200 Fax 03 9899 7465 New Zealand Black & Decker 81 Hugo Johnston Drive Penrose, Auckland, New Zealand Tel. 09 579 7600 Fax 09 579 8200 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD Tel.
5100052-08 20 03/03
