HPL108MT
A B D C 2 E
F G H I J 3
ENGLISH (Original instructions) Intended use Your Black & Decker oscillating tool has been designed for DIY applications such as sanding operations. It is also suitable for cutting wooden materials, plastic, gypsum, non-ferrous metals and fastening elements (e.g., unhardened nails, staples), working soft wall tiles and scraping of small surfaces. This tool is intended for consumer use only. Safety instructions General power tool safety warnings @ Warning! Read all safety warnings and all instructions.
(Original instructions) d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use.
ENGLISH (Original instructions) Safety of others u u This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Residual risks.
(Original instructions) u If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard. ENGLISH Rigid scraper. (Part number - X26135-XJ) Ideal for removal of hard and soft material from flat surfaces such as Features the removal of vinyl flooring, bonded This tool includes some or all of the following features. 1. On/Off switch 2. Variable speed dial 3. Super-lokTM Tool free accessory clamping lever 4. Battery 5.
ENGLISH (Original instructions) Fitting and removing the accessories (fig. C - H) Warning! Before fitting an accessory, disconnect the tool from the mains supply. Fitting a Black & Decker / Piranha accessory (fig. C - E) u Hold the tool and squeeze the accessory clamping lever (3). u Slide the accessory (13) between the shaft and the accessory holder making sure the accessory engages all eight pins on the holder and is flush with the shaft. u Release the accessory clamping lever.
(Original instructions) Charger diagnostics If the charger detects a weak or damaged battery, the charging indicator (11) will flash red at a fast rate. Proceed as follows: u Re-insert the battery (4). u If the charging indicators continues flashing red at a fast rate, use a different battery to determine if the charging process works properly. u If the replaced battery charges correctly, the original battery is defective and should be returned to a service centre for recycling.
ENGLISH (Original instructions) Maintenance Your Black & Decker corded/cordless appliance/tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Warning! Before performing any maintenance on corded/ cordless power tools: u Switch off and unplug the appliance/tool. u Or switch off and remove the battery from the appliance/ tool if the appliance/tool has a separate battery pack.
(Original instructions) EC declaration of conformity MACHINERY DIRECTIVE % HPL108MT Black & Decker declares that these products described under "technical data" are in compliance with: 2006/42/EC, EN 60745-1, EN 60745-2-4 These products also comply with Directive 2004/108/EC and 2011/65/EU. For more information, please contact Stanley Europe at the following address or refer to the back of the manual.
X26125 X26115 X26130 X26110 E16389 19 49 53 52 51 55 54 48 50 10 9 8 12 1 18 17 14 11 15 16 46 www.2helpU.
ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black & Decker in your country.
Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD 90586772 REV-0 Tel. 03-8720 5100 Fax 03-9727 5940 Tel. +64 9 259 1133 Fax +64 9 259 1122 Tel.
