® {zy ,ÃÂÁÀCBA@| |{zy ,ÃÂÁÀCBA@ AA{y ,ÂÀB@ CC ÁÁ ÃÃ zz || AA{y ,ÂÀB@ CC ÁÁ ÃÃ zz || KD574 KD577 KD1000
Congratulations! On the purchase of your Black & Decker corded drill. To ensure the best results from your corded drill please read these safety and usage instructions carefully. If you have any questions or queries after reading this manual please do not hesitate to call your local service and information centre (the number is towards the back of this manual).
Contents Page 4 Safety instructions Double insulation Page 5 Electrical safety Mains plug replacement Extension cables Unwanted tools and the environment The Black & Decker guarantee Page 6 After sales service for your Black & Decker product Our after sales service policy Accessories Technical data Features Page 7 Fitting the drill bit Removing the chuck Fitting the side handle Preparing your drill for operation Page 8 Using your drill Handy hints Cooling down Overload EC declaration of conformity
Corded drills user manual SAFETY INSTRUCTIONS Warning! When using electric tools, the following basic safety precautions should always be taken to reduce the risk of fire, electric shock and personal injury. Read all these instructions before attempting to operate the product and save this booklet. For safe operation: • Keep the work area clean. Cluttered areas and benches invite injuries. • Consider the work area environment. Do not expose the power tool to rain and do not use in damp or wet locations.
ENGLISH from the mains power supply. This is done by placing insulation barriers between the electrical and mechanical components making it unnecessary for the tool to be earthed. Note: Double insulation does not take the place of normal safety precautions when operating the tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool. ELECTRICAL SAFETY Be sure the supply is the same as the voltage given on the rating plate.
ENGLISH AFTER SALES SERVICE FOR THE BLACK & DECKER PRODUCT (UK, AUSTRALIA AND NEW ZEALAND ONLY) Black & Decker offers a nationwide network of authorised service agents. The use of other than genuine Black & Decker accessories and parts may damage or reduce the performance of your Black & Decker product and may also endanger the user. The terms and conditions of the warranty may also be effected.
ENGLISH FITTING THE DRILL BIT (KEYLESS CHUCKS) Proceed as follows: Disconnect the plug from the electricity supply. While holding the rear section of the chuck, rotate the front section until the jaws of the chuck are sufficiently open. Insert the drill bit in the jaws of the chuck. Hold the rear section of the chuck while tightening the front section. Twist the two sections firmly in opposite directions to securely grip the drill bit.
,À@y y,À@ ENGLISH yy @@ ÀÀ ,, @@ ÀÀ ,, yy @@ ÀÀ ,, yy @@ ÀÀ ,, yy Set the forward/ reverse switch to the desired direction of rotation. Never change the setting of the hammer switch, the speed switch, the torque speed control or the forward/reverse when your drill is in operation. USING YOUR DRILL To switch your drill on, depress the on/off switch or the variable speed switch. Your drill stops when the on/off switch or the variable speed switch is released.
Australia Black & Decker (A’asia) Pty Ltd 286-288 Maroondah Highway North Croydon, Victoria 3136 Tel: 03 9213 8200 Fax: 03 9726 7150 New Zealand Black & Decker 483 Great South Road, Penrose, Auckland Tel: 09 579 7600 Fax: 09 579 8200 South Africa Black & Decker South Africa (Pty) Ltd Suite no 107, PostNet X65, Halfway House 1685 Tel: 011 314 4431 Fax: 011 314 4435 United Kingdom Black & Decker 210 Bath Road, Slough Berkshire SL1 3YD Tel: 01753 574277 Tlx: 848317 BAND MH Fax: 01753 551155 10Part
Data protection act: Tick this box if you prefer not to receive information from Black & Decker or other companies.
GUARANTEE CARD South Africa: Black & Decker South Africa (Pty) Ltd, Suite no 107, PostNet X65, Halfway House 1685 United Kingdom & Ireland: PO Box 821, Slough, Berkshire, SL1 3AR Please complete this section immediately after the purchase of your corded drill and post it to the Black & Decker address in your country (above). If you live in Australia or New Zealand, please register your purchase by using the alternative guarantee card supplied. 12 Part no. 808378-52 5/98.
