Powerful Solutions 1 2 3 6 5 TM 4 12 7 11 10 9 www.blackanddecker.co.
English 2 (Original instructions) 5
17 16 9 14 13 15 11 A B 23 22 21 C 19 20 18 D 3
24 25 21 26 8 E 28 27 29 G 4 F 30 6 H
Intended use Your Black & Decker saw has been designed for sawing wood and wood products. This tool is intended for consumer use only. Safety instructions General power tool safety warnings @ Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. Service a.
Safety instructions for circular saws with outer or inner pendulum guards and with tow guard a. Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut. b.
Electrical safety # u This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard. Additional safety instructions for lasers + Read all of this manual carefully. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
u u The height difference between the toothed rim and the lower end of the riving knife should be 2 - 3 mm. Tighten the screws. Fitting and removing the parallel fence (fig. C) u The parallel fence is used to saw in a straight line parellel to the edge of the workpiece. Fitting u Loosen the locking knob (18). u Insert the parallel fence (19) through the openings (20). u Slide the parallel fence into the desired position. u Tighten the locking knob. Removing u Loosen the locking knob.
Dust extraction An adaptor is required to connect a vacuum cleaner or dust extractor to the tool. u Insert the dust extraction adaptor into the saw dust outlet (12). u Connect the vacuum cleaner hose to the adaptor. Maintenance Your Black & Decker corded/cordless appliance/tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.
Input voltage VAC Power input W No-load speed min-1 Max. depth of cut mm Depth of cut at 45° bevel mm Blade diameter mm Blade bore mm Blade tip width mm Laser properties: Laser class Wave length nm Laser power mW Weight kg KS1600L TYPE1 230 1,600 5,000 65 50 190 16 2.3 2 650 <5 5.
ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black & Decker in your country.
Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD 90555815 Tel. 03-8720 5100 Fax 03-9727 5940 Tel. +64 9 259 1133 Fax +64 9 259 1122 Tel.