Powerful Solutions 3 1 2 6 5 TM 4 8 7 11 13 10 9 www.blackanddecker.co.
English 2 (Original instructions) 5
20 19 18 15 16 17 14 2-3 mm 13 2-3 mm A B 21 6 5 11 12 C 22 D 3
25 8 7 24 23 11 E F 26 G 4
Intended use Your Black & Decker saw has been designed for sawing wood and wood products. This tool is intended for consumer use only. Safety instructions General power tool safety warnings @ Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. Service a.
Safety instructions for circular saws with outer or inner pendulum guards and with tow guard a. Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut. b.
Electrical safety # u This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard. Features 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
Switching on and off Warning! Make sure that the Allen key is removed from the blade retaining screw before switching on. Switching on u Keep the lock-off button (2) depressed and press the on/off switch (1). u Release the lock-off button. Switching off u Release the on/off switch. Aligning the saw with the cutting line (fig. F) The saw is equipped with 2 guides for straight cutting (23) and 2 guides for 45° mitre cutting (24). u Align the left edge of the guides (23) or (24) with the cutting line (25).
You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com Technical data Input voltage Power input No-load speed Max.
TYP 1 KS40 10 3 19 2 12 24 11 20 6 3 18 17 1 28 7 40 8 9 24 23 41 42 17 14 18 22 23 25 5 13 27 39 4 37 15 38 31 16 43 32 46 26 33 36 35 29 49 30 34 821 817 50 Max 5 mm 2 mm E13165 WWW.2helpU.
ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black & Decker in your country.
Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD 90555640 Tel. 03-8720 5100 Fax 03-9727 5940 Tel. +64 9 259 1133 Fax +64 9 259 1122 Tel.
