MFL143
A 2 B C D E
F G H I J 3
ENGLISH (Original instructions) Intended use Your Black & Decker multi-purpose tool has been designed for a wide range of DIY applications. Using the drill/screwdriver head, this tool is intended for screwdriving applications and for drilling in wood, metal, plastics and soft masonry. Using the saw head, this tool is intended for sawing wood, metal and plastics. Using the sander head, this tool is intended for sanding wood, metal, plastics and painted surfaces.
(Original instructions) b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d.
ENGLISH u u u u u Keep blades sharp. Dull or damaged blades may cause the saw to swerve or stall under pressure. Always use the appropriate type of saw blade for the workpiece material and type of cut. When cutting pipe or conduit, make sure that they are free from water, electrical wiring, etc. Do not touch the workpiece or the blade immediately after operating the tool. They can become very hot.
(Original instructions) When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time.
ENGLISH (Original instructions) Fitting and removing a drill bit or screwdriver bit The drill/screwdriver head is fitted with a keyless chuck to allow for an easy exchange of bits. u Lock the tool by setting the forward/reverse slider (2) to the centre position. u Open the chuck (9) by turning the front part clockwise with one hand while holding the rear part with the other. u Insert the bit shaft into the chuck (9).
(Original instructions) Charger diagnostics If the charger detects a weak or damaged battery, the charging indicator (19) will flash red at a fast rate. Proceed as follows: u Re-insert the battery (5). u If the charging indicators continues flashing red at a fast rate, use a different battery to determine if the charging process works properly. u If the replaced battery charges correctly, the original battery is defective and should be returned to a service centre for recycling.
ENGLISH u u u (Original instructions) Do not force the saw blade into the workpiece. Note that cutting sheet metal will normally take more time than sawing thicker wooden workpieces. Spread a thin film of oil along the cutting line before sawing. To cut, switch the tool on and move it down until the saw blade is exactly over the point of entry. Lower the rear of the shoe towards the workpiece, maintaining a firm pivoting pressure on the saw shoe.
ENGLISH (Original instructions) Batteries Z u Run the battery down completely, then remove it from the tool. NiCd, NiMH and Li-Ion batteries are recyclable. Take them to any authorised repair agent or a local recycling station. 905531** (typ. 1) Input voltage VAC 230 Output voltage VDC 16.4 Current mA 200 h 5-7 Approx. charge Technical data time MFL143 (H1) Voltage Charger VDC 14.4 Drill / Screwdriver Level of sound pressure according to EN 60745: Sound pressure (LpA) 82.
ENGLISH (Original instructions) Guarantee Black & Decker is confident of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.
21 E16391 1 3 2 16 4 14 15 5 6 www.2helpU.com 17 7 MFL143 20 11 8 12 13 9 10 20 - 06 - 11 18 19 TYP.
ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black & Decker in your country.
Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD 90577357 REV-0 Tel. 03-8720 5100 Fax 03-9727 5940 Tel. +64 9 259 1133 Fax +64 9 259 1122 Tel.
