Powerful Solutions www.blackanddecker.co.
English 2 (Original instructions) 7
1 18 15 16 2 17 3 14 4 13 12 5 6 7 11 10 9 8 19 26 20 25 21 24 22 23 3
22 27 21 28 8 29 22 24 30 31 32 12 33 24 34 33 32 4
16 14 25 1 26 35 36 5
38 37 39 24 40 41 26 Q 44 42 43 R 6 S
Intended use Your Black & Decker sliding compound mitre saw has been designed for sawing wood, plastic and non-ferrous metal only. Safety instructions General power tool safety warnings Warning! Read all safety warnings and all ! instructions. Failure to follow all instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f.
The blade guard on your saw will automatically raise when the arm is brought down; it will lower over the blade when the arm is raised. The guard can be raised by hand when installing or removing saw blades or for inspection of the saw. Never raise the blade guard manually unless the machine is switched off. Check periodically that the motor air slots are clean and free of chips. Do not work with material containing asbestos. Asbestos is considered to be carcinogenic.
Warning! The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used. The vibration level may increase above the level stated.
Assembly Warning! Before assembly, make sure that the tool is switched off and unplugged. Note: This tool is accurately adjusted before shipping from the factory. Check the following accuracy and readjust them if necessary in order to obtain the best results in operation. Laser beam The laser beam alignment is set at manufacturing source and is not user adjustable. Mitre angle adjustment (fig.
Hold the main operating handle (2) and pull the carriage (16) forward until the centre of the saw blade is over the front of the work piece. Operate the on/off switch (25) and press the saw arm release lever (26) to lower the cutting head. When the saw reaches full speed, push the main operating handle (2) down slowly, cutting through the leading edge of the workpiece. Slowly move the main operating handle (2) toward the fence to complete the cut.
Settings Vertical position (back of moulding is against the fence) Bevel angle 0° Outside Mitre Right at Left at corner angle 45° 45° Moulding Bottom Bottom position against against table table Finished Keep left Keep side side of right side cut of cut Horizontal position (Back of moulding is flat on the table) 45° 0° 0° Top Bottom against against fence fence Keep Keep right side right side of cut of cut Crown moulding cut Crown moulding can only be cut flat on the table with this mitre saw.
changing the blades. Use correctly sharpened saw blades. Observe the maximum speed and tooth type marked on the saw blade. Only use Black & Decker recommended blades. To replace the blade (24), proceed as follows: Using a screwdriver, loosen but do not remove the screw (37). Do not remove the screw completely as it will make re-assembly difficult. Using a screwdriver, loosen but do not remove the screw (38). Do not remove the screw completely as it will make re-assembly difficult.
Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual.
To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our aftersales service and contacts are available on the Internet at: www.2helpU.com Please visit our website www.blackanddecker.co.
TYP.
ENGLISH Do not forget to register your product! www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black & Decker in your country.
$XVWUDOLD %ODFN 'HFNHU $XVWUDOLD 3W\ /WG )OHWFKHU 5RDG 0RRURROEDUN 9LFWRULD 1HZ =HDODQG %ODFN 'HFNHU 7H $SXQJD 3ODFH 0W :HOOLQJWRQ $XFNODQG 8QLWHG .