G A F B C D E H I L O P M N Q EN K J BDX19301-4B
PACKAGE CONTENTS PART A B C D E F G H I PART DESCRIPTION QTY Handle (To be assembled before use) Switch Latch Vacuum port Dust tank Blowing port Power cord wrap Accessory holder Caster(To be assembled before use) DESCRIPTION J Hose K Extension wand Floor nozzle Foam filter Disposable filter bag Reusable filter Gulper nozzle Crevice nozzle L M N O P Q 1 1 2 1 1 1 1 1 4 PART NUMBERS QTY BDVA13-3304 1 BDVA25-1205 BDVA13-1570 BDVA20-1200A BDVA25-1238N BDVA20-1100N BDVA13-1588 BDVA13-1508 3 1 1
PRODUCT SPECIFICATIONS Model Voltage / Frequency / Wattage Motor Tank Capacity Hose Power cord BDX19301-4B 240V / 50Hz / 850W By-Pass, Single Stage 15 Litre 32mmx1.5m H05VV-F, 2C x 0.75mm² / 1.83m. Length WARNING: Use only extension cords that are rated for outdoor use. Extension cords in poor condition or that are too small in wire size can pose fire and shock hazards.
EXPRESS WARRANTY STATEMENT WET/DRY VACUUM You are not required to do anything to register your wet/dry vacuum purchase. Please attach the purchase receipt to this manual and ensure both are kept safe. We hope you enjoy your new wet/dry vacuum , and if you have any problems call customer service on the above phone numbers. Do not return to place of purchase.
COMPLETE WARRANTY STATEMENT – WET/DRY VACUUM As soon as you have purchased the wet/dry vacuum, we recommend that you check to make sure it is intact and that you read the operating instructions carefully before using it. The purchase receipt for this product is to be retained and must be presented if making a claim under the terms of the Smart Marketing Group (SMG) warranty. Bank account statements are not acceptable for proof of purchase.
SAFETY INFORMATION IMPORTANT SAFETY INSTRUCTIONS & GROUNDING INSTRUCTIONS When using an electrical appliance, basic precautions should be always followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. ATTENTION! Read all safety rules carefully before attempting to operate. Retain for future reference. DANGER! Never operate this unit when flammable materials or vapors are present because electrical devices produce arcs or sparks that can cause a fire or explosion.
20. Do not pick up soot, cement, plaster or drywall dust without filter and dust bag in place. These are very fine particles that may affect the performance of the motor or be exhausted back into the air. Additional dust bags are available. 21. Do not leave the cord lying on the floor once you have finished the cleaning job. It can become a tripping hazard. 22. Use special care when emptying heavily loaded tanks. 23. To avoid spontaneous combustion, empty tank after each use. 24.
(1) (2) ASSEMBLY (1) (2) INSTALLING HANDLE To install handle 1. Place handle in recess (3) 2. Insert provided screws (1) 3. Use Phillips screwdriver to secure and tighten. (3) (3) INSTALLING CASTERS Use provided casters and insert into the bottom of caster dolly as shown in Figure (A). Strong pressure required and listen for the click to ensure locked in place.
The filter must always be in correct position to reduce the risk of leaks and possible damage to vac. Make sure that the filter is completely covering the filter cage and that the clamp ring is as close to the lid as possible. Make sure there are no gaps between the filter and the lid (See illustration). It is very important to assemble the filter to the cage without allowing any possible leaks or tears.
EMPTY THE TANK WARNING! To reduce the risk of injury from accidental starting, unplug power cord before emptying the dust tank. step 1 step 2 step 3 BLOWING OPERATION WARNING! Always wear safety eyewear complying with ANSI Z87.1 (or in Canada CSA Z94.3) when using as a blower. WARNING! To avoid injury to bystanders, keep them clear of blowing debris. CAUTION Wear a dust mask if blowing creates dust which might be inhaled.
CARE AND MAINTENANCE FILTER REPLACEMENT WARNING! To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter.Your filter should be cleaned often to maintain peak vacuum performance. IMPORTANT To avoid damage to the blower wheel and motor, always reinstall the reusable dry filter before using the vacuum for dry pickups and always reinstall the foam filter before using the vacuum for wet pickups.
TROUBLESHOOTING WARNING! TO REDUCE THE RISK OF INJURY FROM MOVING PARTS AND/OR ELECTRICAL SHOCK, TURN SWITCH OFF AND DISCONNECT GROUNDED PLUG FROM ELECTRICAL OUTLET BEFORE PERFORMING TROUBLESHOOTING CHECKS. Minor problems often can be fixed without calling customer service.
EXPANDED VIEW / PARTS LIST PART DESCRIPTION QTY PART DESCRIPTION QTY 1 Handle 1 10 Silencer sponge 1 2 Switch 1 11 Tray sealing strip 1 3 Top cover 1 12 Filter cage 1 Latch 2 1 4 Baffle 1 13 5 Crimp cap 1 14 Dust tank 6 Cord clamp 1 15 Vacuum port 1 7 Power cord 1 16 Caster dolly 1 8 Lid 1 17 Caster 4 9 Motor 1 13
Do not return to place of purchase. Smart Marketing Group Pty Ltd CUSTOMER SERVICE Australia: 1300 660 457 New Zealand: 0800 474 876 Operating times: Monday – Friday 8.00am - 5.00 pm Australian Eastern Standard Time (AEST) 33-35 Lionel Road, Mt. Waverley Victoria 3149, Australia. ©2020 Manufactured under license for Black & Decker Corporation by Alton Industry Ltd Group. Made in China. Product in this box may differ slightly from that pictured.