VEC1093DBD Fu||y Automatic Smart Battery E|ectro.
VECI093DBD Manual 050205 5/5/05 iMPORTANT IS NO£MAL BAT[ERY GAS MIXTURES -- WORKING DANGEROUS. 3. BATEERIES G£NERAT£ FOR R£ASON, OPERATION. This equipmer_ THIS USING YOUR £XAC_Y. To reduce risk of bakery the battery manufacturer vicinity of battery. Page ii SAFETY iNSTRUCTiONS THAT EACH TIM£ BEFORE FOLLOW THE INSTRUCTIONS 2. PM F12ure WARNINGS I.
VECI093DBDManual 5 6 050205 For negative-grounded (POS, P +) ungrounded engine block paris¸ Connect For away from batter_ body When vehicle¸ parts¸ Connect clamp battery 8 Do not charge the 9 See operating instructions clip iv to carburetor, or sheet-meal body (BLACK) clamp AC metal part cord, remove from of the frame clamp battery or engEne from charger Io block¸ vehicle while for the el_gine lenglh chassis¸ and then information¸ has been To reduce remov
VECI093DBDManual 050205 5/5/05 6:32 PM Page 2 Stage TMZO -- Absorption Charge maintains the maximum possible charge at a constant, safe, predetermined voltage. During this phase, the charging voltage remains constant, while the actual charging current is reduced to allow for the maximum proper internal chemical energy transfel. At the end of Stage 2, the charger will automatically move into Stage 3 charge mode.
VECI093DBDManual 050205 5/5/05 6:32 PM Page 4 OPERATING INDICATOR: Large (.375") 3-Character Digital indicates the various conditions and/or St_mJsCodes are described Display in the upper left of the control panel status codes: in the following chart and on the back of charger. iNSTRUCTIONS Ensure that all installation and operating instructions and safety precautions are understood and carefully followed by anyone installing or using the charger.
Pressing the4/10/20/40AMPbutton repeatedly advances tostandby mode; theunitsounds a beep, displays "000"andstops charging. 4.Thebattery charger displays thecharge current. Toviewtilebattery voltage, press BATTERY VOLTAGE button. Thecharger willsound a beepanddisplay the battery voltage for3seconds, thenreturns todisplaying thecharge current. B.Thedisplay shows "FUL" whenthebattery isfullycharged. 6.Follow thesteps outlined in"Important Safety Instructions" atthefrontofthis manual todisconnect.
BATTERY RECONDITION MODE should only be used with 10 Amp Hour (Ah) or larger capacity lead-acid batteries, Charge the battery to be treated for 20 minutes, before using RECONDITION Mode. Observe the Digital Display tar any codes. This initial charge will check the battery for shorted cells (F01), open cells (FO3) or battery too low to accept a charge (FO2), and to ensure the battery carl take a charge. If code (FO3) is displayed, change to the BATTERY RECONDITION MODE.
TROUBLESHOOTING Display Indications/Common Problems/Possible Solutions No Far.lions • Check and make sure the charger • Follow the steps outlined F01 -- Internal is plugged in the Operating Shorted into a live 1 ! 0/! 20 volt AC outlet, Instructions section. Celt Battery If the battery being charged has an internal shorted cell, tile F01 wil! show, We recommend taking your battery to a certified automotive service center for evaluation.
FIVE YEAR LIMITRD WARRANTY PROGRAM This limited warranty progr.Rm is the only one that applies to INs producl, and il sets futth _ill the responsibilities of Vector Manu_cluringr reoz_rding this product¸ There is no olher warrant_L o_her than th_ de_ribed helein This Vector Manu_c[urirlg produc[ is warranted.
