Instruction Manual Book Item code: BH143 Glow and EP ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED. 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 1,750 mm (68.90 in). - Length: 1,280 mm (50.39 in). - Weight: 4.2 - 4.5 kg (9.25 - 9.92 lbs). - Wing area: 48.9dm2. - Wing loading: 92.04g/dm2. - Servo mount: size (29 x 13 x 30) mm. - Wing type: Naca airfoil. - Gear type: Electric retract gear, size: 81 x 44 x 29 mm (not included). Oleo struts (included).
Instruction manual HE-111 Item code: BH143 TABLE OF CONTENTS Introduction...............................................2 Installing the rudder linkages...................20 Warranty....................................................3 Installing the engine mount......................22 Disclaimer.................................................3 Installing the electric motor (ep version)..22 Safety precaution......................................3 Secure the wing to the fuselage...............
Instruction manual WARRANTY Black Horse Model guarantees the component parts in this kit to be free from defects in both material and workmanship at the date of purchase by the purchaser. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product.
Instruction manual FLIGHT WARNINGS When ready to fly, first extend the transmitter aerial. Switch on the transmitter. Switch on the receiver. Check that the wings are correctly fitted to the fuselage. Operate the control sticks on the transmitter and check that the control surfaces move freely and in the CORRECT directions. Check that the transmitter batteries have adequate power. ALWAYS take off into the wind.
Instruction manual HE-111 Item code: BH143 • Officially designated AMA Air Show Teams (AST) are authorized to use devices and practices as defined within the Team AMA Program Document. (AMA Document #718.) (j) Not operate a turbine-powered aircraft, unless in compliance with the AMA turbine regulations. (AMA Document #510-A.) 3.
Instruction manual HE-111 Item code: BH143 PARTS LISTING (NOT INCLUDED) Servo extension leads. 330mm .... 2 pcs. Engine: .25 ci glow... 2pcs 330mm .....3 pcs. 190mm .... 2 pcs. Propeller. Suit with your engine. LiPo. 3S - 3000- 4000mAh. 12AWG 200oC BATTERY 450mm ...... 2 pcs. 2 Packs MOTOR Motor: Admiral GP2 3520-950kV ..... 2 pcs. Servos size: (29.0 x 13.0 x 30.0)mm. Torque servos: 4.8V (3.02kg/cm), 6V (3.53kg/cm) ............ 7 pcs ESC ESC: 65A ....... 2 pcs.
Instruction manual HE-111 Item code: BH143 1 : Fuselage. 2 : Wing panel ( 2a, 2b ). 3 : Canopy fuselage ( 3a: front canopy, 3b: main canopy, 3c: top canopy, 3d: Bottom canopy, 3e: Pilot). 4 : Horizontal stabilizer ( 4a, 4b ). 14 : Landing gear mount. 5 : Rudder. 15 : Main gear struts. 6 : Cowling ( 6a, 6b). 7 8 9 10 11 3a 3e 3c 16 : Wheels. : Spinner ( 75mm ). : Aluminium wing dihedral brace. 17 : Fuel tank hatch plastic. : Aluminium elevator dihedral brace. : Tail gear set.
Instruction manual HE-111 Item code: BH143 INSTALLING THE AILERONS AND FLAPS Bottom view Aileron Flap 1) Test fit the aileron to the wing with the hinges. If the hinges dont’t remain centered, stick a pin through the middle of the hinge to hold it in position. 1 C.A Temporary pin to keep hinge centered 2) Apply drops of thin CA to the top and bottom of each hinge. Do not use CA accelerator. After the CA has fully hardened, test the hinges by pulling on the aileron. 2 C.
Instruction manual HE-111 Item code: BH143 Bottom view For Aileron Servo For Flap Servo 4 4 Aileron and flap servos. Flap Aileron 90 60 o o 2mm approx.16mm 2 For Flap. 1.5mm 2 For Flap For Aileron. 2x10mm TP Screw For Aileron TP Screw 2mm 1.5mm 2x10mm TP Screw - - - - - - - 16 1.5mm Warning! 2x10mm Bottom view Pay close attention here. Assemble left and right sides the same way. 2 The number of times the same way Assembly (in this case twice). Cut off shaded portion carefully.
Instruction manual HE-111 Item code: BH143 Bottom view INSTALLING THE AILERONS AND FLAPS LINKAGES 1) Working with the aileron linkage for now, thread one nylon clevis onto one of the threaded wires. 2) Attach the clevis to the outer hole in the control horn. 3) Locate one nylon servo arm, and using wire cutters, remove all but one of the arms. Using a 2mm drill bit, enlarge the third hole out from the center of the arm to accommodate the aileron pushrod wire.
Instruction manual HE-111 Item code: BH143 Nylon Clevis Pushrod 2 Horn Pushrod Flaslink 1.
Instruction manual HE-111 Item code: BH143 INSTALLING THE MAIN GEAR There are two options: 1. MAIN LANDING GEAR 2. ELECTRIC LANDING GEAR RETRACTS ELECTRIC GEAR DIMENSIONAL DETAIL (mm) 42 30 81 2.5 44 35 29 17 XWAVE RM400-90 REACT SHOWN ELECTRIC NOT INCLUDED. 5.1 4.20 3x15mm Tp Screw ----8 3 x 10mm Wheel Collar --- -----2 5x38mm Socket Head Cap Screw ------2 4x4mm Setscrew --- -----2 2 pcs. ONLY INCLUDING OLEO STRUTS. 4x4mm 3x10mm 5x38mm Landing gear mount. 75mm Wheels.
Instruction manual HE-111 Item code: BH143 OPTION 1: MAIN GAER STRUTS Drill holes using the stated. 2.5mm (in this case 1.5mm ). Apply instant glue C . A (C.A glue, super glue). Assemble left and right sides the same way. 3 x 15mm Screw C.A Bottom view 2.
Instruction manual HE-111 OPTION 2: ELECTRIC GEAR RETRACTS Screw 3 x 15mm C.A 2.
HE-111 Instruction manual Item code: BH143 HORIZONTAL STABILIZER INSTALLATION 1. Using a modeling knife, cut away the covering from the fuselage for the stabilizer and remove it. 2. Remove the covering from the stabilizer. When cutting through the covering to remove it, cut with only enough pressure to only cut through the covering it's self. Cutting into the balsa structure may weaken it. This could lead to possible failure during flight. 3. Attach the wing to the fuselage as picture. 4.
Instruction manual HE-111 Item code: BH143 Top view A = A’ B = B’ B A 16 A’ B’
Instruction manual HE-111 Item code: BH143 INSTALLING THE TAIL GEAR AND RUDDER 5mm Wheel Collar -----------1 4x4mm Setscrew 2mm Nylon Collar -----------1 3x12mm TP Screw ----------2 --- -----1 2mm 4 x 4mm 5mm Tail Gear . Bottom view A B C.A A C.A A B Apply epoxy glue. B Apply instant glue C . A (C.A glue, super glue). Cut off shaded portion carefully A B Secure nylon hinges with instant glue being careful vertical and rudder. Align the center line of vertical fin with rudder.
Instruction manual HE-111 Item code: BH143 3 x 12 mm Bottom view A B Take off the main wing after put a rudder. 90 Degree A B Apply epoxy glue. Pay close attention here. INSTALLATION THE ELEVATOR PUSHROD 1. Locate the pushrod exit slot on the right side and left side of the fuselage. It is located slightly ahead and below the horizontal stabilizer. 2. Carefully cut away the covering material from the slot. 3.
Instruction manual B 2 HE-111 Apply epoxy glue. Horn The number of times the same way Assembly (in this case twice). 2.5mm Item code: BH143 Push rod Nylon clevis Cut off excess. B Cut off shaded portion carefully. Pay close attention here. Horn 2 Must be purchased separately! Bottom view 1.7 x 8mm Cap Screw 2 Servo arm Push rod 6mm Flaslink Bend 90o 2 2mm approx.
Instruction manual HE-111 Elevator Servo INSTALLATION THE RUDDER LINKAGES 2mm approx.
Instruction manual Nylon Clevis 800mm Push rod Flaslink Horn -----1 -----1 -----1 -----1 HE-111 Item code: BH143 Nylon Clevis B Push rod 2.5mm Horn 1.7x8mm Cap Screw 1.7x8 mm Cap Screw -----1 Horn Top view 90 A B 2.5mm Apply epoxy glue. Drill holes using the stated. (in this case 2.5mm ).
Instruction manual HE-111 Item code: BH143 Top view Rudder Pushrod Rudder Servo INSTALLATION THE ENGINE MOUNT There are two options: 1. ELECTRIC MOTOR 2.
Instruction manual HE-111 Item code: BH143 Top view 4 x 16mm 10 x 40mm 4mm 4 x 60mm Top view Assemble left and right sides the same way.
Instruction manual HE-111 Item code: BH143 Top view 95mm . Assemble left and right sides the same way. SECURE THE WING TO THE FULSELAGE 512mm 19 Aluminium -----1 ●Attack the wings to the joiner tube and secure the wing panels to the fuse lage. ●Main wing must be inserted and attached completely before fixing with crew.
Instruction manual HE-111 Item code: BH143 Top view 4x15mm Top view 25
Instruction manual HE-111 INSTALLING THE RECEIVER AND BATTERY 1. Plug the servo leads and the switch lead into the receiver. You may want to plug an aileron extension into the receiver to make plugging in the aileron servo lead easier when you are installing the wing. Plug the battery pack lead into the switch. 2. Wrap the receiver and battery pack in the protective foam to protect them from vibration. Use a rubber band or masking tape to hold the foam in place.
Instruction manual HE-111 Item code: BH143 MOUNTING THE COWL 3 x 12mm TP Screw ----------8 Plastic Part B -----4 B Top view When rotating clock wise, change the connection of 2 wires. Motor Lead < Check the motor rotation > Assemble left and right sides the same way. B Apply epoxy glue.
Instruction manual HE-111 Item code: BH143 3 x 12mm Tp Screw Top view C.A 2.5mm C.A 2.5mm 48mm 16mm 205mm 100mm 3 x 12mm Tp Screw C.A C.A 2.5mm Bottom view 3 x 12mm Tp Screw 2.5mm C.A C.A 2.5mm 2.5mm C.A 2.5mm Apply instant glue C . A (C.A glue, super glue). 28 Assemble left and right sides the same way. 1.5mm Drill holes using the stated. (in this case 1.5mm ). Cut off shaded portion carefully.
Instruction manual HE-111 Item code: BH143 INSTALLATION THE STOPPER 30mm Screw Rubber Aluminium Rubber Aluminium 29
Instruction manual HE-111 Item code: BH143 Inflame ! 9mm Bend 400 degree Bend 400 degree WARNING Do not overheat, it may break. 12mm 400 40 degree bend 6mm 400 INSTALLING THE FUEL INSTALLATION THE TANK FUEL TANK 1) Using a modeling knife, cut one length of silicon fuel line (the length of silicon fuel line is calculated by how the weighted clunk should rest about 8mm away from the rear of the tank and move freely inside the tank).
Instruction manual HE-111 Item code: BH143 Clunks 3 x 12mm Tp Screw ----------1 ------4 Fuel tank hatch plastic ----------1 Fuel Tank 3 x 12mm -----2 ------2 Silicone Tube Fuel Tank Foam Ring 2 Bottom view 1.5mm 2 2 Bottom view Assemble left and right sides the same way. 2 The number of times the same way Assembly (in this case twice).
Instruction manual HE-111 Item code: BH143 INSTALLATION THE ENGINE 4mm Flat Washer ----------8 4mm Spring Washer ----------8 3 x 20mm Cap Screw -----8 4x30mm Cap Screw ----8 Size: 25 2 30mm 2 2 Top view . 4mm Flat Washer 4mm Spring Washer 4 x 30mm Cap Screw Assemble left and right sides the same way. Apply threadlocker (screw cement). The number of times same way Assembly 2 the (in this case twice).
Instruction manual HE-111 Item code: BH143 Top view 3x20mm Cap Screw Assemble left and right sides the same way.
Instruction manual HE-111 Item code: BH143 INSTALLING THE THROTTLE 1. Install one adjustable metal connector through the third hole out from the center of one servo arm, enlarge the hole in the servo arm using a 2mm drill bit to accommodate the servo connector. Remove the excess material from the arm. After installing the adjustable metal connector apply a small drop of thin C/A to the bottom nut. This will prevent the connector from loosening during flight. 2.
Instruction manual HE-111 Item code: BH143 MOUNTING THE COWL 1. Remove the muffler and needle valve assembly from the engine. Slide the fiberglass cowl over the engine. 4. While holding the cowl firmly in position, drill four 1,6mm pilot holes through both the cowl and the side edges of the firewall. 2. Measure and mark the locations to be cut out for engine head clearance, needle valve, muffler.
Instruction manual HE-111 Item code: BH143 Top view 3 x 12mm Tp Screw C.A 2.
Instruction manual HE-111 Item code: BH143 Top view 3 x 12mm Tp Screw C.A 2.5mm 3 x 12mm Tp Screw C.A 2.5mm C.A Bottom view 2.
Instruction manual HE-111 Item code: BH143 Bottom view INSTALLING CANOPY FUSELAGE Position the canopy so the rear frame on the canopy is aligned with the rear edge of the cockpit opening. Use canopy glue to secure the canopy to the canopy hatch. Use low-tack tape to hold the canopy in position until the glue fully cures. Wrap the tape completely around the canopy hatch. A B Top view A B 38 Apply epoxy glue.
Instruction manual HE-111 Item code: BH143 Top view Adhesive tape.
Instruction manual HE-111 Item code: BH143 Top view Open / Close Bottom view Bottom view 40
Instruction manual HE-111 Item code: BH143 Bottom view Adhesive tape. Bottom view INSTALLING THE SPINNER Install the spinner back-plate, propeller and spinner cone. ! The propeller should not touch any part of the spinner cone. If it dose, use a sharp modeling knife and carefully trim away the spinner cone where the propeller comes in contact with it.
Instruction manual Top view 3 x12 mm Tp Screw Must be purchased separately! 42 HE-111 Item code: BH143
Instruction manual HE-111 BALANCING 1) It is critical that your airplane be balanced correctly. Improper balance will cause your plane to lose control and crash. THE CENTER OF GRAVITY IS LOCATED 130MM BACK FROM THE LEADING EDGE OF THE WING. AT THE FUSELAGE. BALANCE A PLANE UPSIDE DOWN WITH THE FUEL TANK EMPTY. 2) Mount the wing to the fuselage. Using a couple of pieces of masking tape, place them on the top side of the wing 96mm back from the leading edge, at the fuselage sides.
Instruction manual HE-111 Item code: BH143 FOR YOUR RADIO INSTALLATION BASIC CONNECTION FOR AIRPLANE AND ADJUSTMENT OF SERVOS ● For more information, refer to radio system instruction manual. Example of connection ● Follow instruction manual of Engine and Battery.
Instruction manual HE-111 Item code: BH143 MAIN GEAR DIMENSIONAL DETAIL MAIN GEAR STRUTS LANDING GEAR MOUNT 5mm 40mm 51mm 41mm 31mm 125mm 44mm TAIL GEAR DIMENSIONAL DETAIL 8mm 12mm 21mm 75mm 37mm 1.5mm hold 5.
Instruction manual HE-111 Item code: BH143 DECORATION DECORATION < Top view > < Bottom view > < Side view > Left < Side view > Right 46
4x m 70m 47 4mm 4mm 0 4x3 4m mm m m 4m M3 d Blin 4x4mm Nut 2mm 2x10mm 3x12mm EXPLODED VIEW 0m 3x2 m 4x3 0 4m mm Nylon Clevis m 4m m 3x12mm 1.7x8mm 1.7x8mm m 0m 3x2 4x 70m m 2mm 2x10mm 4x4mm 4mm 4mm 3x12mm 4 x 15mm Nylon Clevis M3 ut dN Blin 1.7x8mm m 3x12m 4x4mm Nylon Clevis 1.7x8mm 3x10mm 5x35mm 3x15mm 1.7x8mm Nylon Clevis 1.7x8mm 1.
I/C FLYING WARNING Always operate in open areas, away from factories, hospitals, schools, buildings NEVER fly near power lines,aerials or other dangerous areas including airports, motorways etc. ALWAYS adjust the engine from behind the propeller, and do not allow any part of your body to be in line with the propeller. and houses etc. NEVER fly your aircraft close to people or built up areas. D O NO T di s po s e of em pty fu el containers on a fire, this can lead to an explosion.
I/C FLYING GUIDE When ready to fly, first extend the transmitter aerial. Operate the control sticks on the transmitter and check that the control surfaces move freely and in the CORRECT directions. ALWAYS land the model INTO th e wind , this en su res tha t th e model lands at the slowest possible speed. OFF - ON OFF - ON OFF - ON Switch on the transmitter. Check that the transmitter batteries have adequate power. Switch off the receiver . OFF - ON OFF - ON OFF - ON Switch on the receiver .
