Installation manual

ManualsBrandsBlack Widow Security ManualsHome building and DecorBW 3 Channel

BW-2500

PREMIER

PLUS

INSTALLATION MANUAL

Please read this Manual carefully before attempting to install this system.

BEFORE INSTALLING THE BW-2500 PREMIER PLUS

• DO read through this installation manual.

• DO NOT install the alarm brain in an engine compartment.

• The alarm may arm itself when power is first connected.This is a normal condition.

ITEMS SUPPLIED WITH THE BW-2500

BWS-2502 Receiver and Control Module BWS-260 Valet Switch

BWS-385 2-Button, 3-channel, Code BWS-180 LED Status Indicator

Learning Transmitters (2)

BWS-12025 Wiring Harness, Fuseholder,

MTS-20W Programmable, Multi-tone, and Fuse

120 dB Siren

SPDT Relay

BWS-296 Dual Zone Electronic BRS-003 Relay Socket

Shock Sensor

OPTIONAL ACCESSORIES Backup Battery ..................................................BWS-500

Radar Field Sensor.........................................MAS-2 Remote Starting.................................................RAS-101

Window Rollup.............................................WRM-2 Leather Transmitter Case ...............................BWS-390

Power Door Lock........................................PDL-50 Trunk Release ........................................................TR-100

SPECIFICATIONS

Operating voltage...............+12 VDC Neg. Ground

Code Learning ......................................3 Codes Max.

Current consumption.........5 mA (max) disarmed.

Siren output drive ......................................3 Amperes

Automatic reset........................................60 seconds.

Door Lock/Unlock Output ...................(-) 500 mA.

Channel 2 Output Drive........................(-) 500 mA.

Channel 3 Output Drive..................(-) 500 mA, variable.

Remote control transmit freq.............................310 mHz.

Passive arming delay............................30 Seconds approx.

Auxiliary output drive..........................250 mA maximum.

Flashing output drive............................10 Amp maximum.

Trigger inputs..............................................1) Neg. pnswtch.

1) Pos. pnswtch. 1) Neg. sensor or aux. pnswtch.

Dome light output.....................................500 mA ground.

Summary of content (8 pages)

PAGE 1
INSTALLATION MANUAL BW-2500 PREMIER PLUS Please read this Manual carefully before attempting to install this system. BEFORE INSTALLING THE BW-2500 PREMIER PLUS • DO read through this installation manual. • DO NOT install the alarm brain in an engine compartment. • The alarm may arm itself when power is first connected.This is a normal condition.
PAGE 2
-1INSTALLATION INSTRUCTIONS IMPORTANT: Make all wiring connections to the vehicle before connecting the main 14-pin and auxiliary 2-pin connector harnesses to the receiver and control module. 1. Before mounting the BWS-2502 Receiver and Control Module, you must set the PROGRAMMING DIPSWITCHES for the kind of operation the customer wants. These are the switch settings available; Standard (Default) settings are in “BOLD” type: Switch #1 Door Lock and Unlock Pulse Time: ON = 3/4 seconds. OFF = 3 seconds.
PAGE 3
-210. Complete the general wiring of the main harness by connecting... A. The RED wire to a source of CONSTANT +12vdc. IMPORTANT: Remove the 15 amp fuse from the harness before connection. B. The BLACK wire to a good chassis GROUND point. C. The WHITE wire for POSITIVE pinswitches. or... The BLUE/WHITE wire for NEGATIVE pinswitches. (NOTE: If your installation requires BOTH inputs, they can both be used on the same installation) D. The GREEN wire to a source of TRUE IGNITION. E.
PAGE 4
-3- CONNECTOR PIN NUMBERS AND WIRE COLOR CODES 14-PIN HARNESS # COLOR FUNCTION 1) Red +12 VDC 2) Wht/Org 3) Orange Parking Light (+) Siren (+) 4) Grn/Blk 5) Yellow 6) Gray 7) 8) Red/Blk Wht/Yel 9) Blue (–) Trip 10) Violet Valet (–) 11) Green Ignition 12) Black Ground 13) White 14) Blu/Wht Positive Door (+) Negative Door (–) Door Lock (–) Door Unlock (–) Starter Interrupt (–) LED (–) Dome Light (–) NOTES Main Power.
PAGE 5
-4TROUBLESHOOTING WIRING DIAGRAM TRUNK RELEASE, REMOTE START 2nd/3rd Channel Molex Ignition +12V MUST NOT DROP OUT during starting of vehicle.
PAGE 6
-5- POWER DOOR LOCK INSTRUCTIONS: POSITIVE TRIGGER DOOR LOCK CIRCUIT: TO DOOR LOCK RELAY The BW-2500 comes equipped to handle ground door lock installations.The Yellow and Green wires from the Receiver Module are ready to tap into grounding door lock systems. The following instructions require two SPDT Relays, not included in the BW2500.These Relays must be ordered separately.
PAGE 7
-6TROUBLESHOOTING PROBABLE CAUSE SUGGESTED CORRECTION Unit is triggered any time it is armed. BLUE wire is shorted to ground or the BWS-296 or optional sensor is not correctly adjusted. Disconnect the wire to see if the symptom stops. If so, check the wire for shorts or readjust sensor fittings. Alarm will not rearm or will not passively arm. WHITE wire is connected to positive voltage, BLU/WHT wire is connected to ground, GREEN wire is connected to permanent positive voltage, or pinswitch is bad.
PAGE 8
LIMITED LIFETIME WARRANTY The Black Widow Division of DLC, Inc. warrants to the original purchaser that the vehicle alarm system purchased will be free from defects in workmanship. If it is determined that a defect exists, at our option, we will repair defective parts or replace the system. If product is defective within one (1) year from date of purchase, item will be repaired or replaced at no cost to original purchaser.