Installation manual

ManualsBrandsBlack Widow Security ManualsHome building and DecorBW RAS 100

BEFORE INSTALLING THE STARTER DISABLE/KEYLESS ENTRY SYSTEM

•

DO read through this installation manual.

•

DO NOT install the control module in an engine compartment.

•

The alarm may arm itself when power is first connected.This is a normal condition.

ITEMS SUPPLIED WITH THE STARTER DISABLE/KEYLESS ENTRY SYSTEM

• Receiver and control module • Valet/override switch

• Two 2-Button or 3-button, code learning • LED status indicator

transmitters

• Wiring harness, fuseholder, & fuse

• Door lock harness

OPTIONAL ACCESSORIES

Backup battery...............................................BWS-500 Window roll up...........................................................WRM-2

Remote starter ..............................................RAS-101 Power door lock.........................................................PDL-50

Trunk release .....................................................TR-100 Relay ....................................................................................SPDT

Starter disable relay socket.........................BRS-003 5-wire door lock relay & socket ...............BRS-008P16

(+) door lock Inverter..............................BW-34516

SPECIFICATIONS

Operating voltage..................+12 VDC Neg. Ground

Code learning..........................................3 Codes Max.

Current consumption............5 mA (max) disarmed.

Door lock/unlock output .........................(-) 500 mA.

Channel 2 output drive.............(-) 500 mA variable.

Remote control transmit frequency.......................310 mHz.

Passive arming delay..................................30 Seconds approx.

Auxiliary output drive...............................250 mA maximum.

Flashing output drive .................................(-) 250 mA 30 sec.

Dome light output......................................(-) 250 mA 30 sec.

INSTALLATION MANUAL

STARTER

DISABLE/

KEYLESS

ENTRY

SYSTEM

INSTALLATION MANUAL

Summary of content (7 pages)

PAGE 1
I N S TA L L AT I O N M A N U A L STARTER DISABLE/ KEYLESS ENTRY SYSTEM BEFORE INSTALLING THE STARTER DISABLE/KEYLESS ENTRY SYSTEM • DO read through this installation manual. • DO NOT install the control module in an engine compartment. • The alarm may arm itself when power is first connected.This is a normal condition.
PAGE 2
-1INSTALLATION INSTRUCTIONS IMPORTANT: Make all wiring connections to the vehicle before connecting the main 6-pin harness and all plug-in connectors to the receiver control module. 1. Before mounting the Control Module, you must set the PROGRAMMING DIPSWITCHES for the kind of operation the customer wants. These are the switch settings available; Standard (Default) settings are in “BOLD” type: Switch #1 Door Lock and Unlock Pulse Time: ON = 3/4 seconds. OFF = 3 seconds.
PAGE 3
-211. Connect the Main 6-Pin Wiring Harness and all pin connectors to the Control Module. Install the fuse in the RED wire of the main wiring harness. 13. Code Learning Procedure: To add a new remote to the system, turn ignition key ON, OFF, ON, OFF, and leave on (3 times). Siren/Horn will chirp once. Press override/valet switch for 5 seconds, you will hear 3 chirps. You now have 5 seconds to press the arm buttons on the remotes that you want to operate the system.
PAGE 4
-3- CONNECTOR PIN NUMBERS AND WIRE COLOR CODES 6 PIN HARNESS PIN 1) Wire Color Red Function Main Power hook to constant 12v+ source 2) Brown Negative Output for siren or car horn 3) Yellow Ignition Input 12v+ (must not drop out while starting) 4) Black Ground 5) Gray 2nd Channel Output (negative output) 6) White Parking Light/Dome Light Output (negative output). Requires 2 relays for both outputs.
PAGE 5
-4- WIRING DIAGRAM LOCK (-) PULSE GREEN +12V CONSTANT OUTPUT RED UNLOCK (-) PULSE BLUE 1 2 3 4 DIPSWITCH (INSIDE OF MODULE) FUSE RED WIRING HARNESS RECEIVER MODULE (+)12V BROWN HORN/SIREN (-) OUTPUT YELLOW BLACK 12V IGNITION GROUND GRAY 2nd CHANNEL (-) OUTPUT (REQUIRES RELAY) WHITE } PARKING LIGHT (-)OUTPUT (REQUIRES RELAY) STARTER DISABLE INPUT/OUTPUTS BLUE VALET CONNECTOR VALET SWITCH RED LED CONNECTOR DIP SWITCH LED PROGRAMS: (1) Door lock/unlock pulse ON=.75 sec. OFF= 3 sec.
PAGE 6
-5- POWER DOOR LOCK DIAGRAMS: POSITIVE TRIGGER DOOR LOCK CIRCUIT*: TO DOOR LOCK RELAY The Starter Disable/Keyless Entry comes equipped to handle ground door lock installations.The Blue and Green wires from the Receiver Module are ready to tap into grounding door lock systems. The following door lock diagrams require two SPDT Relays or the appropriate accessories not included with the system.These items must be ordered separately.
PAGE 7
PROBABLE CAUSE SUGGESTED CORRECTION Keyless will not go into Code Learning Mode RED or YELLOW wire not connected to the correct power source. Code Learning sequence done to slow. RED wire should connect directly to the battery. Connect YELLOW wire to true ignition wire (Not at Fuse Block). Redo Code Learning sequence faster. Remote Control does not lock and unlock the vehicle. Defective Remote Control. Bad battery. Antenna wire is grounded. Replace Remote Control or its battery. Unground antenna.